网架吊装专项施工方案计划.doc

-/ 编号：编号：SJ1F.1703-11SJ1F.1703-11 创新中心续建工程（公共服务平台）项目创新中心续建工程（公共服务平台）项目 网架结构吊装专项施工方案网架结构吊装专项施工方案 编编 制制 人人 ： 审审 核核 人人 ： 批批 准准 人人 ： 日日 期期 : : -/ 目目 录录 一、编制依据一、编制依据.1 二、工程概况二、工程概况.2 三、施工准备三、施工准备.3 四、网架吊装部署四、网架吊装部署.3 五、网架单元计算五、网架单元计算.6 六、营业执照及税务登记证六、营业执照及税务登记证.41 -/ 一、编制依据一、编制依据 1.11.1 工程相关文件工程相关文件 创新中心续建工程（公共服务平台）项目网架工程建筑图 创新中心续建工程（公共服务平台）项目网架工程结构图 网架结构施工方案 二、工程概况二、工程概况 工程名称创新中心续建工程（公共服务平台）项目 质量标准符合现行的质量验收规范，达到合格标准。 工程简介 本工程为太原不锈钢产业园区创新中心续建工程整个研发中心的裙 房部分网架结构，该网架为正放四角锥焊接空心球结构，上弦多点 支承，网架短向跨26.0米，长向跨度35.7米,厚度1.5米。 两台吊车同时起吊，因网架面积35.7m*26m较大，所以要求吊车司 机配合度相当高。 本工程网架在室外地坪拼装完成，一次性吊到楼内指定位置。 吊装公司山西二牛吊装有限公司 -/ 三、施工准备三、施工准备 3.13.1组织架构组织架构 3.23.2机具准备机具准备 机具设备计划 机械或设备名称规格型号数量备注 汽车吊车260 吨两台吊装网架 交流或直流焊机4 台预埋板焊接 四、网架吊装四、网架吊装部署部署 4.14.1 整体安装部署整体安装部署 网架安装计划先在地面拼装完成除屋面以外，利用汽车吊吊装屋面上与屋面上预埋 板焊接施工方案。在距楼7m位置进行拼装完成，然后用260t的两辆吊车，共同起吊至 屋面。 现场平面图如下: -/ -/ 4.34.3 网架的提升网架的提升 4.3.1网架提升的机具选择 网架的提升计划采用两台260吨汽车吊，吊绳尺寸选用22#，吊点为网架下弦部位，出臂顺序为 222111，钢丝绳选取6分，经过计算汽车吊吊装网架为31吨，单台汽车吊乘以1.2倍系数负荷为18.6 吨。 具体性能表如下： 4.3.2网架提升示意图 -/ 五、网架单元计算五、网架单元计算 5.15.1 网架单元信息（单元号、截面、长度详见网架结构设计图纸）网架单元信息（单元号、截面、长度详见网架结构设计图纸） 网架单元信息表 单元号截面长度(m) 面积 (mm2) 最大轴力 (kN) 最小轴力 (kN) 强度稳定长细比结论 1060 x3.52.7006210.80.80.010.00108 满足 1160 x3.52.7506213.93.90.030.00110 满足 1260 x3.52.7506211.81.80.010.00110 满足 1660 x3.53.0006212.72.70.020.00120 满足 1760 x3.53.0006214.44.40.030.00120 满足 1860 x3.52.8006210.80.80.010.00112 满足 1960 x3.52.7006210.70.70.000.00108 满足 2060 x3.52.7506215.35.30.040.00110 满足 2660 x3.53.0006215.85.80.040.00120 满足 2760 x3.52.8006210.70.70.000.00112 满足 2860 x3.52.7006210.60.60.000.00108 满足 2960 x3.52.7506216.66.60.050.00110 满足 3660 x3.52.8006210.60.60.000.00112 满足 3760 x3.52.7006210.70.70.010.00108 满足 4560 x3.52.8006210.70.70.010.00112 满足 5560 x3.52.7006210.90.90.010.00108 满足 6360 x3.52.8006210.90.90.010.00112 满足 6460 x3.52.7006210.70.70.010.00108 满足 7260 x3.52.8006210.70.70.010.00112 满足 7360 x3.52.7006210.70.70.010.00108 满足 8160 x3.52.8006210.70.70.010.00112 满足 8260 x3.52.7006210.90.90.010.00108 满足 9060 x3.52.8006210.90.90.010.00112 满足 10060 x3.52.7006210.70.70.010.00108 满足 10860 x3.52.8006210.70.70.010.00112 满足 10960 x3.52.7006210.60.60.000.00108 满足 11060 x3.52.7506216.66.60.050.00110 满足 11760 x3.52.8006210.60.60.000.00112 满足 11860 x3.52.7006210.70.70.000.00108 满足 11960 x3.52.7506215.35.30.040.00110 满足 12560 x3.53.0006215.85.80.040.00120 满足 12660 x3.52.8006210.70.70.000.00112 满足 12760 x3.52.7006210.80.80.010.00108 满足 -/ 单元号截面长度(m) 面积 (mm2) 最大轴力 (kN) 最小轴力 (kN) 强度稳定长细比结论 12860 x3.52.7506213.93.90.030.00110 满足 12960 x3.52.7506211.81.80.010.00110 满足 13360 x3.53.0006212.72.70.020.00120 满足 13460 x3.53.0006214.44.40.030.00120 满足 13560 x3.52.8006210.80.80.010.00112 满足 14860 x3.52.370621-3.5-3.50.030.0495 满足 14960 x3.52.370621-7.5-7.50.060.1095 满足 15560 x3.52.370621-7.5-7.50.060.1095 满足 15660 x3.52.370621-3.5-3.50.030.0495 满足 16060 x3.52.3706210.50.50.000.0095 满足 16460 x3.52.370621-10.3-10.30.080.1395 满足 16560 x3.52.400621-18.0-18.00.140.2396 满足 16960 x3.52.400621-18.0-18.00.140.2396 满足 17060 x3.52.370621-10.3-10.30.080.1395 满足 17460 x3.52.3706210.50.50.000.0095 满足 17560 x3.52.3706210.50.50.000.0095 满足 17660 x3.52.3706212.82.80.020.0095 满足 18860 x3.52.3706212.82.80.020.0095 满足 18960 x3.52.3706210.50.50.000.0095 满足 20560 x3.52.3706210.40.40.000.0095 满足 21960 x3.52.3706210.40.40.000.0095 满足 22060 x3.52.3706210.40.40.000.0095 满足 23460 x3.52.3706210.40.40.000.0095 满足 25060 x3.52.3706210.50.50.000.0095 满足 25160 x3.52.3706213.43.40.030.0095 满足 26360 x3.52.3706213.43.40.030.0095 满足 26460 x3.52.3706210.50.50.000.0095 满足 26560 x3.52.3706210.50.50.000.0095 满足 26960 x3.52.370621-11.1-11.10.080.1495 满足 27060 x3.52.400621-18.7-18.70.140.2496 满足 27460 x3.52.400621-18.7-18.70.140.2496 满足 27560 x3.52.370621-11.1-11.10.080.1495 满足 27960 x3.52.3706210.50.50.000.0095 满足 28360 x3.52.370621-4.3-4.30.030.0595 满足 28460 x3.52.370621-8.7-8.70.070.1195 满足 29060 x3.52.370621-8.7-8.70.070.1195 满足 29160 x3.52.370621-4.3-4.30.030.0595 满足 -/ 单元号截面长度(m) 面积 (mm2) 最大轴力 (kN) 最小轴力 (kN) 强度稳定长细比结论 29560 x3.51.975621-2.0-2.00.010.0279 满足 29660 x3.52.750621-2.0-2.00.010.03110 满足 29860 x3.53.000621-2.7-2.70.020.05120 满足 29960 x3.53.000621-3.1-3.10.020.05120 满足 30160 x3.53.000621-3.2-3.20.020.06120 满足 30360 x3.51.975621-2.6-2.60.020.0379 满足 30460 x3.52.750621-9.1-9.10.070.16124 满足 30560 x3.52.875621-1.6-1.60.010.03129 满足 30960 x3.53.000621-10.2-10.20.080.21135 满足 31060 x3.52.200621-2.5-2.50.020.0388 满足 31160 x3.51.975621-1.9-1.90.010.0279 满足 31860 x3.52.200621-2.1-2.10.020.0288 满足 31960 x3.51.975621-3.2-3.20.020.0379 满足 32660 x3.52.200621-3.5-3.50.030.0488 满足 34360 x3.51.975621-0.3-0.30.000.0079 满足 35060 x3.52.2006210.30.30.000.0088 满足 35160 x3.51.975621-0.1-0.10.000.0079 满足 35860 x3.52.2006210.10.10.000.0088 满足 35960 x3.51.975621-0.3-0.30.000.0079 满足 36660 x3.52.2006210.30.30.000.0088 满足 38360 x3.51.975621-3.2-3.20.020.0379 满足 39060 x3.52.200621-3.5-3.50.030.0488 满足 39160 x3.51.975621-1.9-1.90.010.0279 满足 39860 x3.52.200621-2.1-2.10.020.0288 满足 39960 x3.51.975621-2.6-2.60.020.0379 满足 40060 x3.52.750621-9.1-9.10.070.16124 满足 40160 x3.52.875621-1.6-1.60.010.03129 满足 40560 x3.53.000621-10.2-10.20.080.21135 满足 40660 x3.52.200621-2.5-2.50.020.0388 满足 40760 x3.51.975621-2.0-2.00.010.0279 满足 40860 x3.52.750621-2.0-2.00.010.03110 满足 41060 x3.53.000621-2.7-2.70.020.05120 满足 41160 x3.53.000621-3.1-3.10.020.05120 满足 41360 x3.53.000621-3.2-3.20.020.06120 满足 41860 x3.52.3706213.63.60.030.0095 满足 42560 x3.52.3706213.63.60.030.0095 满足 42960 x3.52.250621-1.9-1.90.010.0290 满足 -/ 单元号截面长度(m) 面积 (mm2) 最大轴力 (kN) 最小轴力 (kN) 强度稳定长细比结论 43260 x3.52.3706212.22.20.020.0095 满足 43960 x3.52.3706212.22.20.020.0095 满足 44260 x3.52.250621-1.9-1.90.010.0290 满足 44360 x3.52.2506214.44.40.030.00101 满足 45660 x3.52.2506214.44.40.030.00101 满足 45760 x3.52.250621-3.7-3.70.030.0490 满足 47060 x3.52.250621-3.7-3.70.030.0490 满足 47160 x3.52.250621-4.5-4.50.030.0590 满足 48460 x3.52.250621-4.5-4.50.030.0590 满足 48560 x3.52.250621-4.1-4.10.030.0590 满足 49860 x3.52.250621-4.1-4.10.030.0590 满足 49960 x3.52.2506214.24.20.030.00101 满足 51260 x3.52.2506214.24.20.030.00101 满足 51360 x3.52.250621-2.2-2.20.020.0390 满足 52660 x3.52.250621-2.2-2.20.020.0390 满足 53060 x3.52.3706215.15.10.040.0095 满足 53760 x3.52.3706215.15.10.040.0095 满足 54260 x3.52.077621-1.3-1.30.010.0183 满足 54460 x3.51.9356213.23.20.020.0077 满足 54560 x3.52.4176210.60.60.000.0097 满足 54660 x3.52.417621-2.1-2.10.020.0397 满足 54760 x3.52.297621-0.2-0.20.000.0092 满足 54860 x3.52.2976212.42.40.020.0092 满足 55160 x3.52.297621-0.5-0.50.000.0192 满足 55260 x3.52.297621-3.2-3.20.020.0492 满足 55460 x3.52.4916211.61.60.010.00100 满足 55560 x3.52.3746214.64.60.030.0095 满足 55760 x3.52.491621-2.4-2.40.020.03100 满足 55860 x3.52.491621-1.9-1.90.010.03100 满足 55960 x3.52.3746212.42.40.020.0095 满足 56060 x3.52.3746212.62.60.020.0095 满足 56160 x3.52.4916211.21.20.010.00100 满足 56460 x3.52.3746215.35.30.040.0095 满足 56760 x3.52.374621-3.3-3.30.020.0495 满足 56860 x3.52.374621-0.3-0.30.000.0095 满足 56960 x3.52.491621-2.1-2.10.020.03100 满足 57060 x3.52.4916210.20.20.000.00100 满足 -/ 单元号截面长度(m) 面积 (mm2) 最大轴力 (kN) 最小轴力 (kN) 强度稳定长细比结论 57160 x3.52.3746212.92.90.020.0095 满足 57260 x3.52.374621-0.3-0.30.000.0095 满足 57360 x3.52.108621-1.0-1.00.010.0184 满足 57560 x3.51.9686213.33.30.030.0079 满足 57760 x3.52.840621-0.2-0.20.000.00114 满足 57860 x3.52.004621-0.7-0.70.010.0180 满足 57960 x3.52.840621-2.2-2.20.020.04114 满足 58060 x3.52.0046213.23.20.020.0080 满足 58160 x3.52.355621-3.8-3.80.030.0594 满足 58260 x3.52.355621-4.7-4.70.040.0694 满足 58360 x3.52.355621-1.3-1.30.010.0294 满足 58460 x3.52.35562110.810.80.080.0094 满足 58560 x3.52.3556211.91.90.010.00106 满足 58660 x3.52.3556215.05.00.040.00106 满足 58760 x3.52.35562113.613.60.100.00106 满足 58860 x3.52.35562112.212.20.090.00106 满足 58960 x3.52.430621-7.7-7.70.060.1097 满足 59060 x3.52.430621-1.2-1.20.010.0297 满足 59160 x3.52.43062111.811.80.090.0097 满足 59260 x3.52.430621-1.8-1.80.010.0297 满足 59360 x3.52.430621-2.2-2.20.020.0397 满足 59460 x3.52.430621-1.9-1.90.010.0397 满足 59560 x3.52.4306212.42.40.020.0097 满足 59660 x3.52.4306212.82.80.020.0097 满足 59760 x3.52.430621-1.4-1.40.010.0297 满足 59860 x3.52.430621-8.3-8.30.060.1197 满足 59960 x3.52.430621-2.5-2.50.020.0397 满足 60060 x3.52.43062113.313.30.100.0097 满足 60160 x3.52.4306214.84.80.040.00109 满足 60260 x3.52.4306211.31.30.010.00109 满足 60360 x3.52.43062111.011.00.080.00109 满足 60460 x3.52.43062113.613.60.100.00109 满足 60560 x3.52.430621-4.9-4.90.040.0697 满足 60660 x3.52.430621-4.0-4.00.030.0597 满足 60760 x3.52.43062111.611.60.090.0097 满足 60860 x3.52.430621-1.7-1.70.010.0297 满足 60960 x3.52.036621-0.6-0.60.000.0181 满足 -/ 单元号截面长度(m) 面积 (mm2) 最大轴力 (kN) 最小轴力 (kN) 强度稳定长细比结论 61060 x3.52.8406210.20.20.000.00114 满足 61160 x3.52.0366213.13.10.020.0081 满足 61260 x3.52.840621-2.5-2.50.020.04114 满足 61360 x3.52.8406211.31.30.010.00114 满足 61460 x3.52.0046210.90.90.010.0080 满足 61560 x3.52.840621-3.1-3.10.020.05114 满足 61660 x3.52.0046211.31.30.010.0080 满足 61760 x3.52.355621-4.5-4.50.030.0694 满足 61860 x3.52.3556212.82.80.020.0094 满足 61960 x3.52.355621-8.0-8.00.060.1094 满足 62060 x3.52.35562110.710.70.080.0094 满足 62160 x3.52.355621-28.2-28.20.210.41106 满足 62260 x3.52.355621-28.9-28.90.220.42106 满足 62360 x3.52.355621-45.7-45.70.340.66106 满足 62460 x3.52.355621-48.4-48.40.360.70106 满足 62560 x3.52.4306213.93.90.030.0097 满足 62660 x3.52.430621-3.6-3.60.030.0597 满足 62760 x3.52.43062112.112.10.090.0097 满足 62860 x3.52.430621-10.9-10.90.080.1497 满足 62960 x3.52.4306211.51.50.010.0097 满足 63060 x3.52.4306211.81.80.010.0097 满足 63160 x3.52.430621-0.7-0.70.010.0197 满足 63260 x3.52.430621-1.1-1.10.010.0197 满足 63360 x3.52.430621-3.7-3.70.030.0597 满足 63460 x3.52.4306214.24.20.030.0097 满足 63560 x3.52.430621-11.3-11.30.080.1597 满足 63660 x3.52.43062112.312.30.090.0097 满足 63760 x3.52.430621-30.3-30.30.230.46109 满足 63860 x3.52.430621-30.5-30.50.230.46109 满足 63960 x3.52.430621-51.5-51.50.390.78109 满足 64060 x3.52.430621-48.1-48.10.360.72109 满足 64160 x3.52.4306214.14.10.030.0097 满足 64260 x3.52.430621-4.4-4.40.030.0697 满足 64360 x3.52.4306219.99.90.070.0097 满足 64460 x3.52.430621-8.5-8.50.060.1197 满足 64560 x3.52.0366211.11.10.010.0081 满足 64660 x3.52.8406211.61.60.010.00114 满足 -/ 单元号截面长度(m) 面积 (mm2) 最大轴力 (kN) 最小轴力 (kN) 强度稳定长细比结论 64760 x3.52.0366211.11.10.010.0081 满足 64860 x3.52.840621-3.4-3.40.030.05114 满足 65260 x3.52.004621-1.1-1.10.010.0180 满足 65360 x3.52.3556210.60.60.000.0094 满足 65560 x3.52.355621-11.1-11.10.080.1494 满足 65660 x3.52.355621-3.6-3.60.030.0594 满足 65760 x3.52.35562118.518.50.140.0094 满足 65860 x3.52.35562117.517.50.130.0094 满足 65960 x3.52.355621-15.9-15.90.120.2094 满足 66060 x3.52.355621-18.5-18.50.140.2394 满足 66160 x3.52.43062117.917.90.130.0097 满足 66260 x3.52.4306212.12.10.020.0097 满足 66360 x3.52.430621-3.7-3.70.030.0597 满足 66460 x3.52.430621-14.2-14.20.110.1997 满足 66560 x3.52.4306217.37.30.050.0097 满足 66660 x3.52.4306217.57.50.060.0097 满足 66760 x3.52.430621-6.5-6.50.050.0897 满足 66860 x3.52.430621-6.1-6.10.050.0897 满足 66960 x3.52.4306212.62.60.020.0097 满足 67060 x3.52.43062118.218.20.140.0097 满足 67160 x3.52.430621-14.9-14.90.110.1997 满足 67260 x3.52.430621-3.8-3.80.030.0597 满足 67360 x3.52.43062119.119.10.140.0097 满足 67460 x3.52.43062121.121.10.160.0097 满足 67560 x3.52.430621-20.5-20.50.150.2797 满足 67660 x3.52.430621-17.9-17.90.130.2397 满足 67860 x3.52.4306210.90.90.010.0097 满足 67960 x3.52.430621-3.7-3.70.030.0597 满足 68060 x3.52.430621-11.5-11.50.090.1597 满足 68360 x3.52.036621-1.0-1.00.010.0181 满足 68860 x3.52.004621-2.8-2.80.020.0380 满足 69260 x3.52.355621-3.2-3.20.020.0494 满足 69360 x3.52.3556218.58.50.060.0094 满足 69460 x3.52.35562110.110.10.080.0094 满足 69560 x3.52.355621-7.5-7.50.060.0994 满足 69660 x3.52.355621-9.2-9.20.070.1294 满足 69760 x3.52.43062110.010.00.070.0097 满足 -/ 单元号截面长度(m) 面积 (mm2) 最大轴力 (kN) 最小轴力 (kN) 强度稳定长细比结论 69860 x3.52.4306218.38.30.060.0097 满足 69960 x3.52.430621-4.6-4.60.030.0697 满足 70060 x3.52.430621-11.2-11.20.080.1597 满足 70160 x3.52.43062110.010.00.080.0097 满足 70260 x3.52.43062110.110.10.080.0097 满足 70360 x3.52.430621-9.0-9.00.070.1297 满足 70460 x3.52.430621-8.6-8.60.060.1197 满足 70560 x3.52.4306218.38.30.060.0097 满足 70660 x3.52.43062110.710.70.080.0097 满足 70760 x3.52.430621-11.8-11.80.090.1597 满足 70860 x3.52.430621-4.6-4.60.030.0697 满足 70960 x3.52.43062111.311.30.080.0097 满足 71060 x3.52.4306219.89.80.070.0097 满足 71160 x3.52.430621-10.3-10.30.080.1397 满足 71260 x3.52.430621-8.6-8.60.060.1197 满足 71560 x3.52.430621-3.3-3.30.030.0497 满足 71960 x3.52.036621-2.4-2.40.020.0381 满足 72560 x3.52.3626211.11.10.010.0094 满足 72660 x3.52.3626215.15.10.040.0094 满足 72760 x3.52.362621-3.5-3.50.030.0494 满足 72960 x3.52.3626212.52.50.020.0094 满足 73060 x3.52.3626216.96.90.050.0094 满足 73160 x3.52.362621-3.7-3.70.030.0594 满足 73260 x3.52.362621-2.4-2.40.020.0394 满足 73360 x3.52.4376213.23.20.020.0097 满足 73460 x3.52.4376218.08.00.060.0097 满足 73560 x3.52.437621-1.3-1.30.010.0297 满足 73660 x3.52.437621-6.2-6.20.050.0897 满足 73760 x3.52.4376218.48.40.060.0097 满足 73860 x3.52.4376218.58.50.060.0097 满足 73960 x3.52.437621-6.6-6.60.050.0997 满足 74060 x3.52.437621-6.4-6.40.050.0897 满足 74160 x3.52.4376218.18.10.060.0097 满足 74260 x3.52.4376213.53.50.030.0097 满足 74360 x3.52.437621-6.5-6.50.050.0997 满足 74460 x3.52.437621-1.3-1.30.010.0297 满足 74560 x3.52.4376217.57.50.060.0097 满足 -/ 单元号截面长度(m) 面积 (mm2) 最大轴力 (kN) 最小轴力 (kN) 强度稳定长细比结论 74660 x3.52.4376213.53.50.030.0097 满足 74760 x3.52.437621-3.0-3.00.020.0497 满足 74860 x3.52.437621-4.5-4.50.030.0697 满足 74960 x3.52.4376215.05.00.040.0097 满足 75060 x3.52.4376210.60.60.000.0097 满足 75260 x3.52.437621-2.7-2.70.020.0497 满足 75860 x3.52.0126213.03.00.020.0080 满足 76260 x3.52.3626211.01.00.010.0094 满足 76360 x3.52.362621-0.8-0.80.010.0194 满足 76560 x3.52.3626211.41.40.010.0094 满足 76760 x3.52.362621-0.0-0.00.000.0094 满足 76860 x3.52.362621-0.6-0.60.000.0194 满足 76960 x3.52.4376210.10.10.000.0097 满足 77060 x3.52.4376216.06.00.050.0097 满足 77160 x3.52.437621-1.2-1.20.010.0297 满足 77260 x3.52.437621-2.7-2.70.020.0497 满足 77360 x3.52.4376213.43.40.030.0097 满足 77460 x3.52.4376213.43.40.030.0097 满足 77560 x3.52.437621-2.2-2.20.020.0397 满足 77660 x3.52.437621-2.1-2.10.020.0397 满足 77760 x3.52.4376216.26.20.050.0097 满足 77860 x3.52.4376210.10.10.000.0097 满足 77960 x3.52.437621-2.9-2.90.020.0497 满足 78060 x3.52.437621-1.2-1.20.010.0297 满足 78260 x3.52.4376211.91.90.010.0097 满足 78360 x3.52.437621-0.8-0.80.010.0197 满足 78460 x3.52.437621-0.6-0.60.000.0197 满足 78860 x3.52.437621-0.5-0.50.000.0197 满足 78960 x3.52.0456213.23.20.020.0082 满足 79360 x3.52.8466210.20.20.000.00114 满足 79460 x3.52.0126210.50.50.000.0080 满足 79560 x3.52.8466210.20.20.000.00114 满足 79660 x3.52.0126210.50.50.000.0080 满足 79760 x3.52.3626211.21.20.010.0094 满足 79860 x3.52.362621-0.5-0.50.000.0194 满足 79960 x3.52.36262