最新H3C路由器配置命令17399.doc

精品资料H3C路由器配置命令17399.H3C路由器配置命令一、路由器基本配置命令1、system-view   进入系统视图模式2、sysname R1   为设备命名为R3、display ip routing-table 显示当前路由表4、language-mode Chinese|English 中英文切换5、interface Ethernet 0/0 进入以太网端口视图6、ip address 192.168.1.1 255.255.255.0   配置IP地址和子网掩码7、undo shutdown   打开以太网端口8、shutdown   关闭以太网端口9、quit     退出当前视图模式10、ip route-static 192.168.2.0 255.255.255.0 192.168.12.2 description To.R2 配置静态路由11、ip route-static 0.0.0.0 0.0.0.0 192.168.12.2 description To.R2 配置默认的路由基本配置案例Quidwaydisplay version                          显示版本信息Quidwaydisplay current-configuration            显示当前配置Quidwaydisplay interfaces                       显示接口信息Quidwaydisplay ip route                         显示路由信息Quidwaysysname aabbcc                           更改主机名Quidwaysuper passwrod 123456                    设置口令  Quidwayinterface serial0                        进入接口Quidway-serial0ip address <ip><mask>Quidway-serial0undo shutdown                    激活端口Quidwaylink-protocol hdlc                       绑定hdlc协议Quidwayuser-interface vty 0 4Quidway-ui-vty0-4authentication-mode passwordQuidway-ui-vty0-4set authentication-mode password simple 2Quidway-ui-vty0-4user privilege level 3Quidway-ui-vty0-4quitQuidwaydebugging hdlc all serial0               显示所有信息Quidwaydebugging hdlc event serial0             调试事件信息Quidwaydebugging hdlc packet serial0            显示包的信息静态路由配置案例：Quidwayip route-static <ip><mask>interface number|nexthopvaluereject|blackhole例如：Quidwayip route-static 129.1.0.0 16 10.0.0.Quidwayip route-static 129.1.0.0 255.255.0.0 10.0.0.Quidwayip route-static 129.1.0.0 16 SerialQuidwayip route-static 0.0.0.0 0.0.0.0  10.0.0.动态路由配置案例（RIP）：QuidwayripQuidwayrip workQuidwayrip inputQuidwayrip outputQuidway-ripnetwork 1.0.0.0                       可以allQuidway-ripnetwork 2.0.0.0Quidway-rippeer ip-addressQuidway-ripsummaryQuidwayrip versionQuidwayrip version 2 multicastQuidway-Ethernet0rip split-horizon             ;水平分隔动态路由配置案例（OSPF）：Quidwayrouter id A.B.C.D                       配置路由器的IDQuidwayospf enable                             启动OSPF协议Quidway-ospfimport-route direct                引入直联路由Quidway-Serial0ospf enable area <area_id>      配置OSPF区域标准访问列表命令格式如下：acl <acl-number> match-order config|auto       默认前者顺序匹配。rule normal|specialpermit|deny source source-addr source-wildcard|any例：Quidwayacl 10Quidway-acl-10rule normal permit source 10.0.0.0 0.0.0.25Quidway-acl-10rule normal deny source any二、ACL配置扩展访问控制列表配置命令1.配置TCP/UDP协议的扩展访问列表：rule normal|specialpermit|denytcp|udpsource <ip wild>|anydestination <ip wild>|anyoperate2.配置ICMP协议的扩展访问列表：rule normal|specialpermit|denyicmp source <ip wild>|anydestination <ip wild>|anyicmp-code logging扩展访问控制列表操作符的含义equal portnumber             等于greater-than portnumber       大于less-than portnumber             小于not-equal portnumber             不等range portnumber1 portnumber 区间3.扩展访问控制列表案例Quidwayacl 10Quidway-acl-101rule deny souce any destination anyQuidway-acl-101rule permit icmp source any destination any icmp-type echoQuidway-acl-101rule permit icmp source any destination any icmp-type echo-replyQuidwayacl 10Quidway-acl-102rule permit ip source 10.0.0.1 0.0.0.0 destination 202.0.0.1 0.0.0.0Quidway-acl-102rule deny ip source any destination anyQuidwayacl 103Quidway-acl-103rule permit tcp source any destination 10.0.0.1 0.0.0.0 destination-port equal ftpQuidway-acl-103rule permit tcp source any destination 10.0.0.2 0.0.0.0 destination-port equal wwwQuidwayfirewall enableQuidwayfirewall default permit|denyQuidwayint e0Quidway-Ethernet0firewall packet-filter 101 inbound|outbound4. NAT的配置地址转换配置案例Quidwayfirewall enableQuidwayfirewall default permitQuidwayacl 10Quidway-acl-101rule deny ip source any destination anyQuidway-acl-101rule permit ip source 129.38.1.4 0 destination anyQuidway-acl-101rule permit ip source 129.38.1.1 0 destination anyQuidway-acl-101rule permit ip source 129.38.1.2 0 destination anyQuidway-acl-101rule permit ip source 129.38.1.3 0 destination anyQuidwayacl 10Quidway-acl-102rule permit tcp source 202.39.2.3 0 destination 202.38.160.1 0Quidway-acl-102rule permit tcp source any destination 202.38.160.1 0 destination-port great-than1024Quidway-Ethernet0firewall packet-filter 101 inboundQuidway-Serial0firewall packet-filter 102 inboundQuidwaynat address-group 202.38.160.101 202.38.160.103 poolQuidwayaclQuidway-acl-1rule permit source 10.110.10.0 0.0.0.25Quidway-acl-1rule deny source anyQuidway-acl-1int serial 0Quidway-Serial0nat outbound 1 address-group poolQuidway-Serial0nat server global 202.38.160.101 inside 10.110.10.1 ftp tcpQuidway-Serial0nat server global 202.38.160.102 inside 10.110.10.2 www tcpQuidway-Serial0nat server global 202.38.160.102 8080 inside 10.110.10.3 www tcpQuidway-Serial0nat server global 202.38.160.103 inside 10.110.10.4 smtp udp5. PPP验证配置：主验方：pap|chapQuidwaylocal-user u2 password simple|cipher aaaQuidwayinterface serial 0Quidway-serial0ppp authentication-mode pap|chapQuidway-serial0ppp chap user u1        /pap时，不用此句 pap被验方：Quidwayinterface serial 0Quidway-serial0ppp pap local-user u2 password simple|cipher aaachap被验方：Quidwayinterface serial 0Quidway-serial0ppp chap user u1        Quidway-serial0local-user u2 password simple|cipher aaa