MIPI协约详细介绍.ppt

,MIPI Protocol Introduction,MIPI Development Team 2010-9-2,What is MIPI?,MIPI stands for Mobile Industry Processor Interface MIPI Alliance is a collaboration of mobile industry leaders. Objective to promote open standards for interfaces to mobile application processors. Intends to speed deployment of new services to mobile users by establishing Spec. Board Members in MIPI Alliance Intel, Motorola, Nokia, NXP,Samsung, ST, TI,What is MIPI?,MIPI Alliance Specification for display DCS (Display Command Set) DCS is a standardized command set intended for command mode display modules. DBI, DPI (Display Bus Interface, Display Pixel Interface) DBI：Parallel interfaces to display modules having display controllers and frame buffers. DPI：Parallel interfaces to display modules without on-panel display controller or frame buffer. DSI, CSI (Display Serial Interface, Camera Serial Interface) DSI specifies a high-speed serial interface between a host processor and display module. CSI specifies a high-speed serial interface between a host processor and camera module. D-PHY D-PHY provides the physical layer definition for DSI and CSI.,DSI Layers,DCS spec,DSI spec,D-PHY spec,Outline,D-PHY Introduction Lane Module, State and Line levels Operating Modes Escape Mode System Power States Electrical Characteristics Summary,Introduction for D-PHY,D-PHY describes a source synchronous, high speed, low power, low cost PHY A PHY configuration contains A Clock Lane One or more Data Lanes Three main lane types Unidirectional Clock Lane Unidirectional Data Lane Bi-directional Data Lane Transmission Mode Low-Power signaling mode for control purpose：10MHz (max) High-Speed signaling mode for fast-data traffic：80Mbps 1Gbps per Lane D-PHY low-level protocol specifies a minimum data unit of one byte A transmitter shall send data LSB first, MSB last. D-PHY suited for mobile applications DSI：Display Serial Interface A clock lane, One to four data lanes. CSI：Camera Serial Interface,Two Data Lane PHY Configuration,Lane Module,PHY consists of D-PHY (Lane Module) D-PHY may contain Low-Power Transmitter (LP-TX) Low-Power Receiver (LP-RX) High-Speed Transmitter (HS-TX) High-Speed Receiver (HS-RX) Low-Power Contention Detector (LP-CD) Three main lane types Unidirectional Clock Lane Master：HS-TX, LP-TX Slave：HS-RX, LP-RX Unidirectional Data Lane Master：HS-TX, LP-TX Slave：HS-RX, LP-RX Bi-directional Data Lane Master, Slave：HS-TX, HS-RX,LP-TX, LP-RX, LP-CD,Universal Lane Module Architecture,Lane States and Line Levels,The two LP-TXs drive the two Lines of a Lane independently and single-ended. Four possible Low-Power Lane states (LP-00, LP-01, LP-10, LP-11) A HS-TX drives the Lane differentially. Two possible High Speed Lane states (HS-0, HS-1) During HS transmission the LP Receivers observe LP-00 on the Lines Line Levels (typical) LP：01.2V HS：100300mV (Swing：200mV) Lane States LP-00, LP-01, LP-10, LP-11 HS-0, HS-1,Operating Modes,There are three operating modes in Data Lane Escape mode, High-Speed (Burst) mode and Control mode Possible events starting from the Stop State of control mode Escape mode request (LP-11LP-10LP-00LP-01LP-00) High-Speed mode request (LP-11LP-01LP-00) Turnaround request (LP-11LP-10LP-00LP-10LP-00),Escape Mode,Escape mode is a special operation for Data Lanes using LP states. With this mode some additional functionality becomes available：LPDT, ULPS, Trigger A Data Lane shall enter Escape mode via LP-11LP-10LP-00LP-01LP-00 Once Escape mode is entered, the transmitter shall send an 8-bit entry command to indicate the requested action. Escape mode uses Spaced-One-Hot Encoding. means each Mark State is interleaved with a Space State (LP-00). Send Mark-0/1 followed by a Space to transmit a zero-bit/ one-bit A Data Lane shall exit Escape mode via LP-10LP-11 Ultra-Low Power State During this state, the Lines are in the Space state (LP-00) Exited by means of a Mark-1 state with a length TWAKEUP(1ms) followed by a Stop state.,Escape Mode,Clock Lane Ultra-Low Power State,A Clock Lane shall enter ULPS via LP-11LP-10LP-00 exited by means of a Mark-1 with a length TWAKEUP followed by a Stop State LP-10 TWAKEUP LP-11 The minimum value of TWAKEUP is 1ms,High-Speed Data Transmission,The action of sending high-speed serial data is called HS transmission or burst. Start-of-Transmission LP-11LP-01LP-00SoT(0001_1101) HS Data Transmission Burst All Lanes will start synchronously But may end at different times The clock Lane shall be in High-Speed mode, providing a DDR Clock to the Slave side End-of-Transmission H Toggles differential state immediately after last payload data bit and keeps that state for a time THS-TRAIL,High-Speed Clock Transmission,Switching the Clock Lane between Clock Transmission and LP Mode A Clock Lane is a unidirectional Lane from Master to Slave In HS mode, the clock Lane provides a low-swing, differential DDR clock signal. the Clock Burst always starts and ends with an HS-0 state. the Clock Burst always contains an even number of transitions,Summary for D-PHY,Lane Module, Lane State and Line Levels Lane Module：LP-TX, LP-RX, HS-TX, HS-RX, LP-CD Lane States：LP-00, LP-01, LP-10, LP-11, HS-0, HS-1 Line Levels (typical)：LP：01.2V, HS：100300mV (Swing：200mV) Operating Modes Escape Mode entry procedure ：LP-11LP-10LP-00LP-01LP-00Entry Code LPD (10MHz) Escape Mode exit procedure：LP-10LP-11 High Speed Mode entry procedure：LP-11LP-01LP-00SoT(00011101) HSD (80Mbps 1Gbps) High Speed Mode exit procedure：EoTLP-11 Control Mode - BTA transmission procedure：LP-11LP-10LP-00LP-10LP-00 Control Mode - BTA receive procedure：LP-00LP-10LP-11 System Power States Low-Power mode, High-Speed mode, Ultra-Low Power mode Fault Detection Contention Detection (LP-CD), Watchdog Timer, Sequence Error Detection (Error Report) Global Operation Timing Parameter Clock Lane Timing, Data Lane Timing Other Timing Initialization, BTA, Wake-Up from ULPS Electrical Characteristics HS-RX, LP-RX, LP-TX, LP-CD, Pin characteristic, Clock signal, Data-Clock timing DC and AC characteristic,Outline,DSI Introduction Lane Distributor/Merger Conceptual Packet Structure Data Transmission Way Processor-Sourced Packets Peripheral-Sourced Packets Reverse-Direction LP Transmission Video Mode Summary,Introduction for DSI,DSI is a Lane-scalable interface for increased performance. One Clock Lane / One to Four Data Lanes DSI-compliant peripherals support either of two basic modes of operation Command Mode (Similar to MPU IF) Data Lane 0：bidirectional For returning data, ACK or error report to host Additional Data Lanes：unidirectional. Video Mode (Similar to RGB IF) Data Lane 0：bidirectional or unidirectional; Additional Data Lanes：unidirectional. Video data should only be transmitted using HS mode. Transmission Mode High-Speed signaling mode Low-Power signaling mode Forward/Reverse direction LP transmissions shall use Data Lane 0 only For returning data, DSI-compliant systems shall only use Data Lane 0 in LP Mode Packet Types Short Packet：4 bytes (fixed length) Long Packet：665541 bytes (variable length),Two Data Lanes HS Transmission Example,Data Transmission Way,Separate Transmissions,Separate Transmissions,KEY: LPS Low Power State SP Short Packet SoT Start of Transmission LgP Long Packet EoT End of Transmission,Short Packet Structure,Packet Header (4 bytes) Data Identifier (DI) * 1byte： Contains the Virtual Channel7:6 and Data Type5:0. Packet Data * 2byte：Length is fixed at two bytes Error Correction Code (ECC) * 1byte：allows single-bit errors to be corrected and 2-bit errors to be detected. Packet Size Fixed length 4 bytes The first byte of any packet is the DI (Data Identifier) byte. DI7:6：These two bits identify the data as directed to one of four virtual channels. DI5:0：These six bits specify the Data Type.,Long Packet Structure,Packet Header (4 bytes) Data Identifier (DI) * 1byte：Contains the Virtual Channel7:6 and Data Type5:0. Word Count (WC) * 2byte：defines the number of bytes in the Data Payload. Error Correction Code (ECC) * 1byte：allows single-bit errors to be corrected and 2-bit errors to be detected. Data Payload (065535 bytes) Length = WC bytes Packet Footer (2 bytes)：Checksum If the payload has length 0, then the Checksum calculation results in FFFFh If the Checksum isnt calculated, the Checksum value is 0000h Packet Size 4 + (065535) + 2 = 6 65541 bytes,Data Types for Processor-sourced Packets,Error Correction Code,P7 = 0 P6 = 0 P5 = D10D11D12D13D14D15D16D17D18D19D21D22D23 P4 = D4D5D6D7D8D9D16D17D18D19D20D22D23 P3 = D1D2D3D7D8D9D13D14D15D19D20D21D23 P2 = D0D2D3D5D6D9D11D12D15D18D20D21D22 P1 = D0D1D3D4D6D8D10D12D14D17D20D21D22D23 P0 = D0D1D2D4D5D7D10D11D13D16D20D21D22D23,Checksum,unsigned char xx = 0 x01,0 x5a,0 x5a,0 x03,0 x08,0 x2A, 0 x00,0 x01 ,0 x00,0 xF8,0 x00,0 xF6,0 x57,0 x00,0X00,0 xE5; typedef unsigned short U16; typedef unsigned char U8; U16 CRC_test; U16 crc16_update(U16 crc, U8 a); int main() U16 crc,i; crc = 0 xFFFF; for (i=0; i<1; i+) crc = crc16_update(crc, xxi); CRC_test = crc; ,U16 crc16_update(U16 crc, U8 a) int i; crc =a; for (i = 0; i 1) 0 x8408; else crc = (crc 1); return crc; ,Peripheral-to-Processor LP Transmissions,Detailed format description Packet structure for peripheral-to-processor transactions is the same as for the processor-to-peripheral direction For a single-byte read response, valid data shall be returned in the first byte The second byte shall be sent as 00h If the peripheral does not support Checksum it shall return 0000h,Peripheral-to-Processor LP Transmissions,Peripheral-to-processor transactions are of four basic types Tearing Effect (TE)：trigger message (BAh) Acknowledge：trigger message (84h) Acknowledge and Error Report：short packet (Data Type is 02h) Response to Read Request：short packet or long packet Generic Read Response、DCS Read Response（1byte, 2byte, multi byte） Feature BTA shall take place after every peripheral-to-processor transaction Multi-Lane systems shall use Lane 0 for all peripheral-to-processor transmissions Reverse-direction signaling shall only use LP mode of transmission,Video Mode,DSI supports three formats for Video Mode data transmission Non-Burst Mode with Sync Pulses Non-Burst Mode with Sync Events Burst Mode,Summary for DSI,DSI is a Lane-scalable interface. One Clock Lane One to Four Data Lanes Transmission Mode High-Speed signaling mode (differential signal) (100mV300mV) Low-Power signaling mode (single-ended signal) (0V1.2V) For returning data, only use Data Lane 0 in LP Mode Packet Types Short Packet：4 bytes (fixed length) Data ID (1byte) + Data0 (1byte) + Data1 (1byte) + ECC (1byte) Long Packet：665541 bytes (variable length) Packet Header (4 bytes) + Data Payload (065535 bytes) + Packet Footer (2 bytes) Operation Mode Command Mode (Similar to MPU IF) Video Mode (Similar to RGB IF) Non-Burst Mode with Sync Pulses Non-Burst Mode with Sync Events Burst Mode,Thank you!,