已转化最新版国际标准的实施效果调研表.docx
已转化最新版国际标准的实施效果调研表填报单位： 委员签字或盖单位公章：序号国际标准编号英文名称国内标准编号中文名称对应程度如修改采用，与国际标准的技术差异实施效果实施良好（举例说明）不适用（说明原因）建议改进（改进理由和内容）1ISO 1307:2006Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hosesGB/T 9575-2013橡胶和塑料软管 软管规格和最大最小内径及切割长度公差IDT2ISO 1436:2020Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids SpecificationGB/T 3683-2011橡胶软管及软管组合件 油基或水基流体适用的钢丝编织增强液压型 规范IDT3ISO 1823:2015Rubber hose and hose assemblies for oil suction and discharge service SpecificationHG/T 3038-2008岸上排吸油橡胶软管IDT4ISO 2929:2021Rubber hoses and hose assemblies for bulk fuel delivery by truck SpecificationHG/T 3041-2009油槽车输送燃油用橡胶软管和软管组合件IDT5ISO 3862:2020Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids SpecificationGB/T 10544-2022橡胶软管及软管组合件 油基或水基流体适用的钢丝缠绕增强外覆橡胶液压型 规范IDT6ISO 4023:2009Rubber hoses and hose assemblies for steam Test methodsGB/T 18425-2014蒸汽橡胶软管和软管组合件 试验方法IDT7ISO 4080:2009Rubber and plastics hoses and hose assemblies Determination of permeability to gasGB/T 18422-2013橡胶和塑料软管及软管组合件 透气性的测定IDT8ISO 4642-2:2015Rubber and plastics hoses, non-collapsible, for fire-fighting service Part 2: Semi-rigid hoses (and hose assemblies) for pumps and vehicles2020-0654T-HG消防用不可折叠型橡胶和塑料软管 第2部分：消防泵和消防车用半硬性软管（和软管组合件）IDT9ISO 5771:2008Rubber hoses and hose assemblies for transferring anhydrous ammonia SpecificationGB/T 16591-2013输送无水氨用橡胶软管及软管组合件 规范IDT10ISO 5772:2015Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems SpecificationHG/T 3037-2019计量分配燃油用橡胶和塑料软管及软管组合件MOD1.表1中公称内径由21修改为22。2.表1中公称内径删除了35。3.表1中公称内径由50修改为45。4.附录增加了方法B，适用于4型软管。5.修改了附录I和附录J中项目排序。11ISO 6803:2017Rubber or plastics hoses and hose assemblies Hydraulic-pressure impulse test without flexingGB/T 5568-202X橡胶或塑料软管及软管组合件 无曲挠液压脉冲试验IDT12ISO 6806:2017Rubber hoses and hose assemblies for use in oil burners SpecificationGB/T 24146-2022用于油燃烧器的橡胶软管和软管组合件 规范IDT13ISO 6807:2003Rubber hoses and hose assemblies for rotary drilling and vibration applications SpecificationGB/T 24145-2009旋转钻探和减震用橡胶软管和软管组合件 规范MOD1.表1增加了F级、G级两个级别和对应的压力值。2.表2内径增加了4个规格，细化了最小弯曲半径，增加了各个内径的压力等级。3.表3内径相应增加了4个规格。4.表5增加了F级、G级两个级别。5.6.1.3增加了软管外部连接件、螺纹连接等的压力要求等。6.6.1.4增加了焊接连接的要求。7.8.3增加了f)项。14ISO 7662:1988Rubber and plastics hoses Determination of abrasion of liningGB/T 20026-2005橡胶和塑料软管 内衬层耐磨性测定IDT15ISO 7751:2016Rubber and plastics hoses and hose assemblies Ratios of proof and burst pressure to maximum working pressureGB/T 9574-2017橡胶和塑料软管及软管组合件 验证压力、爆破压力与最大工作压力的比率IDT16ISO 8032:1997Rubber and plastics hose assemblies Flexing combined with hydraulic impulse test (half-omega test)GB/T 12722-2008橡胶和塑料软管组合件 液压脉冲曲挠试验（半试验）IDT17ISO 8033:2016Rubber and plastics hoses Determination of adhesion between componentsGB/T 14905-2020橡胶和塑料软管 各层间粘合强度的测定IDT18ISO 8066-2:2001Rubber and plastics hoses and hose assemblies for automotive air conditioning Specification Part 2: Refrigerant 134aGB/T 20025.2-2005汽车空调用橡胶和塑料软管及软管组合件 耐制冷剂134aIDT19ISO 8331:2016Rubber and plastics hoses and hose assemblies Guidelines for selection, storage, use and maintenanceGB/T 9576-2019橡胶和塑料软管及软管组合件 选择、贮存、使用和维护指南IDT20ISO 10619-3:2011Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 3: Bending tests at high and low temperaturesGB/T 5565.3-2017橡胶和塑料软管及非增强软管 柔性及挺性的测量 第3部分：高温和低温弯曲试验IDT21ISO 11237:2017Rubber hoses and hose assemblies Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids SpecificationGB/T 39313-2020橡胶软管及软管组合件 输送石油基或水基流体用致密钢丝编织增强液压型 规范IDT22ISO/TR 11340:1994Rubber and rubber products Hydraulic hose assemblies External leakage classification for hydraulic systemsGB/Z 18427-2001液压软管组合件 液压系统外部泄漏分级IDT23ISO 11759:1999Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) SpecificationGB/T 20689-2006分配液化石油气（LPGs)用橡胶软管及软管组合件规范IDT24ISO 13363:2016Rubber and plastics hoses for marine-engine wet-exhaust systems SpecificationGB/T 39327-2020船用发动机湿式排气系统用橡胶和塑料软管 规范IDT25ISO 13774:1998Rubber and plastics hoses for fuels for internal-combustion engines Method of test for flammabilityGB/T 20024-2005内燃机用橡胶和塑料燃油软管 可燃性试验方法IDT26ISO 17324:2014Rubber hoses for automotive turbochargers SpecificationGB/T 33381-2016汽车涡轮增压器用橡胶软管 规范MOD国家标准中增加了异型软管的耐真空性能和验证压力的要求。27ISO/TR 17784:2003Rubber and plastics hoses and hose assemblies Guide for use by purchasers, assemblers, installers and operating personnelGB/T 24126-2009橡胶和塑料软管及软管组合件 采购者、组装者、安装者和操作者使用指南IDT28ISO 19013-2:2016Rubber hoses and tubing for fuel circuits for internal combustion engines Specification Part 2: Gasoline fuelsGB/T 24141.2-2022内燃机燃油管路用橡胶软管和纯胶管 规范 第2部分：汽油燃料IDT29ISO 23297:2017Thermoplastic hoses and hose assemblies Wire or synthetic yarn reinforced single-pressure types for hydraulic applications SpecificationGB/T 39311-2020热塑性软管和软管组合件 液压用钢丝或合成纱线增强单一压力型 规范IDT30ISO 28017:2018Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications SpecificationHG/T 2490-2011疏浚工程用 钢丝或织物增强的橡胶软管及软管组合件 规范MOD1.修改了最低适用温度范围，由“-10”改为“-20”。2.增加了公称内径为1300规格的软管。3.修改了软管组合件长度公差，由“±2%”改为“±1%”。4.增加了内衬层、外覆层材料的物理机械性能。31ISO 28702:2008Rubber and plastics hoses and tubing Textile-reinforced types Sub-ambient temperature crush testGB/T 39249-2020橡胶和塑料软管及非增强软管 织物增强型 低温压扁试验IDT32ISO 30013:2011Rubber and plastics hoses Methods of exposure to laboratory light sources Determination of changes in colour, appearance and other physical properties20214107-T-606橡胶和塑料软管 实验室光源暴露试验法 颜色、外观和其它物理特性变化的测定IDT33ISO 3996:1995Road vehicles Brake hose assemblies for hydraulic braking systems used with non-petroleum-base brake fluidGB/T 7127.1-2000使用非石油基制动液的道路车辆 液压制动系统用制动软管组合件IDT34ISO 6120:1995Road vehicles Brake hose assemblies for hydraulic braking systems used with petroleum-base brake fluidGB/T 7127.2-2000使用石油基制动液的道路车辆 液压制动系统用制动软管组合件IDT5
