3020贴片LED灯珠规格书.pdf

TechnicalTechnicalTechnicalTechnicalDataDataDataDataSheetSheetSheetSheetProductProductProductProduct NameNameNameName：PLCCPLCCPLCCPLCC 3020302030203020 HighHighHighHigh BrightBrightBrightBright WhiteWhiteWhiteWhite LEDLEDLEDLEDP P P Partartartart NumberNumberNumberNumber：CustomerCustomerCustomerCustomer：CustomerCustomerCustomerCustomer PNPNPNPN：VersionVersionVersionVersion：A.A.A.A.2 2 2 2DateDateDateDate：InstitutedInstitutedInstitutedInstituted ByByByBy：CheckedCheckedCheckedChecked By:By:By:By:ApprovedApprovedApprovedApproved ByByByBy：CustomerCustomerCustomerCustomer ApprovalApprovalApprovalApprovalMJG01-30W13Z2010.01.011.1.1.1.FeaturesFeaturesFeaturesFeaturesPackage(L/W/H):3.0 2.0 1.3 mmColor:Ultra Bright Standard WhiteLens:Yellow Diffuse Flat MoldEIA STD PackageMeet ROHS,Green ProductCompatible With SMT Automatic EquipmentCompatible With Infrared Reflow Solder AndWave Solder Process2 2 2 2.PackagePackagePackagePackageProfileProfileProfileProfile&SolderingSolderingSolderingSolderingPADPADPADPADSuggestedSuggestedSuggestedSuggestedNotes:1.All dimensions are in millimeters;2.Tolerance is 0.10 mm unless otherwise noted.SolderingSolderingSolderingSoldering PADPADPADPADSuggestedSuggestedSuggestedSuggested：PolarityCathode Mark3.3.3.3.SolderingSolderingSolderingSoldering ProfileProfileProfileProfileSuggestedSuggestedSuggestedSuggested3.1、For Lead Solder3.2、For Lead Free Solder4.4.4.4.AbsoluteAbsoluteAbsoluteAbsoluteMaximumMaximumMaximumMaximum RatingsRatingsRatingsRatingsAtAtAtAtTa=25Ta=25Ta=25Ta=25ParameterParameterParameterParameterSymbolSymbolSymbolSymbolRatingRatingRatingRatingUnitUnitUnitUnitPower DissipationPd90mWPeak Forward Current(1/10 Duty Cycle,0.1ms Pulse Width)IFP100mADC Forward CurrentIF30mAReverse VoltageVR5V V V VOperating Temperature RangeTopr-30C+85CStorage Temperature RangeTstg-40C+90CSoldering ConditionTsolReflow soldering:260C For 5 SecondsHand soldering:300C For 3 Seconds5.5.5.5.ElectricalElectricalElectricalElectricalOpticalOpticalOpticalOptical CharacteristicsCharacteristicsCharacteristicsCharacteristicsAtAtAtAtTa=25Ta=25Ta=25Ta=25Notes:1.Luminous intensity is measured with a light sensor and filter combination that approximates theCIE eye-response curve.2.1/2 is the off-axis angle at which the luminous intensityishalf the axial luminous intensity.3.The dominant wavelength,d is derived from the CIE chromaticity diagram and represents thesingle wavelength which defines the color of the device.ParameterParameterParameterParameterSymbolSymbolSymbolSymbolMin.Min.Min.Min.Typ.Typ.Typ.Typ.Max.Max.Max.Max.UnitUnitUnitUnitTestTestTestTest ConditionConditionConditionConditionLuminous IntensityIV-1200-mcdIF=20mAViewing Angle21/2-120-degIF=20mACIE 1931 CoordinateX/Y-X:0.29Y:0.29-IF=20mAForward VoltageVF2.8-3.6VIF=20mAReverse CurrentIR-10uAVR=5V6.6.6.6.TypicalTypicalTypicalTypical Electrical-OpticalElectrical-OpticalElectrical-OpticalElectrical-OpticalCharacteristicsCharacteristicsCharacteristicsCharacteristics CurvesCurvesCurvesCurves7.7.7.7.LabelLabelLabelLabelExplanationExplanationExplanationExplanationCAT：Luminous Intensity Rank（unit:mcd）HUE：CIE 1931 Coordinate RankREF：Forward Voltage Rank（unit:V）Rank Tolerance:a.Luminous Intensity:15%b.HUE:0.01c.ForwardVoltage:0.1V8.Reel8.Reel8.Reel8.ReelAndAndAndAndTapeTapeTapeTapeDimensionsDimensionsDimensionsDimensions：Notes:1.All dimensions are in millimeters;2.Tolerance is 0.1 mm unless otherwise noted.6013.0PolarityUser Direction9.9.9.9.TapeTapeTapeTapeLeaderLeaderLeaderLeader&TrailerTrailerTrailerTrailerDimensionsDimensionsDimensionsDimensionsAndAndAndAndReelReelReelReel10.10.10.10.PackagingPackagingPackagingPackaging：LabelAluminum moisture-proofbagDesiccantLabelReelVacuum10 bags/carton5 cartons/box11.11.11.11.ReliabilityReliabilityReliabilityReliabilityTestTestTestTestClassificationTestItemTest ConditionReference StandardReferenceStandardEnduranceTestOperation LifeTa=Under Room TemperatureAsPerData Sheet Maximum Rating1000HRS(-24HRS,+72HRS)*20mAMIL-STD-750D:1026MIL-STD-883D:1005JIS C 7021:B-1High Temperature,HighHumidity StorageIR-Reflow In-Board,2 TimesTa=655,RH=9095%240HRS2HRSMIL-STD-202F:103BJIS C 7021:B-11High TemperatureStorageTa=10551000HRS(-24HRS,+72HRS)MIL-STD-883D:1008JIS C 7021:B-10Low TemperatureStorageTa=-5551000HRS(-24HRS,+72H RS)JIS C 7021:B-12EnvironmentalTestTemperatureCycling105 25 -55 2530mins5mins30mins5mins10 CyclesMIL-STD-202F:107DMIL-STD-750D:1051MIL-STD-883D:1010JIS C 7021:A-4ThermalShockIR-Reflow In-Board,2 Times85 5 -40 510mins10mins10 CyclesMIL-STD-202F:107DMIL-STD-750D:1051MIL-STD-883D:1011SolderResistanceT.sol=260 510 1secsMIL-STD-202F:210AMIL-STD-750D:2031JIS C 7021:A-1IR-ReflowNormal ProcessRamp-up rate(183 to Peak)+3/second maxTemp.maintain at 125(25)120 seconds maxTemp.maintain above 183 60-150 secondsPeak temperature range 235+5/-0Time within 5C of actual Peak Temperature(tp)10-30 secondsRamp-down rate+6/second max-MIL-STD-750D:2031.2J-STD-020CIR-ReflowPb Free ProcessRamp-up rate(217 to Peak)+3/second maxTemp.maintain at 175(25)180 seconds maxTemp.maintain above 217 60-150 secondsPeak temperature range 260+0/-5Time within 5C of actual Peak Temperature(tp)20-40 secondsRamp-down rate+6/second max-MIL-STD-750D:2031.2J-STD-020CSolderabilityT.sol=235 5Immersion rate252.5 mm/secCoverage 95%of thedipped surfaceImmersion time 20.5secMIL-STD-202F:208DMIL-STD-750D:2026MIL-STD-883D:2003IEC 68 Part 2-20JIS C 7021:A-212.12.12.12.CautionsCautionsCautionsCautionsApplicationApplicationApplicationApplication1.ALED is a current-operated device.The slight shift of voltage will cause big change of current,whichwill damage LEDs.Customer should use resistors in series for the Over-Current-Proof.2.In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application,it isrecommended to use individual resistor separately,as shown in CircuitAbelow.The brightness of eachLED shown in Circuit B might appear difference due to the differences in the I-V characteristics of thoseLEDs.CircuitCircuitCircuitCircuit modelmodelmodelmodelA A A ACircuitCircuitCircuitCircuit modelmodelmodelmodel B B B B3.High temperature may reduce LEDsintensity and other performances,so keeping it away from heatsource to get good performance is necessary.StorageStorageStorageStorage1.Before opening original package,it is recommended to store them in the following environment:Temperature:530Humidity:85%RH max.2.After opening original package,the storage ambient forthe LEDs should be in 530C temperature and60%or less relative humidity.3.In order to avoid moisture absorption,itisrecommended that the LEDs that out of the original packageshould be stored in a sealed container with appropriate desiccant,or in desiccators with nitrogen ambient.4.The LEDs should be used within 168hrs(7 days)afteropening the package.Once been mounted,solderingshould be quick.5.If the moisture absorbent material(silica gel)has faded away or the LEDs stored out of original packageformore than 168hrs(7 days),baking treatment should be performed using the conditions:60at least24 hours.ESDESDESDESD(ElectrostaticElectrostaticElectrostaticElectrostatic DischargeDischargeDischargeDischarge)-Protection-Protection-Protection-ProtectionALED(especially the Blue、White and Green product)isan ESD sensitive component,and static electricityor powersurge will damage the LED.ESD-damaged LEDs will exhibit abnormal characteristics such ashigh reverse leakage current,low forward voltage,or“no light-up”at low currents,etc.Some advice as below should be noticed:1.Aconductive wrist strap oranti-electrostatic glove should be worn when handling these LEDs.2.All devices,equipment,machinery,work tables and storage racks,etc.must be properly grounded.3.Use anti-static package or boxes to carry and storage LEDs.And ordinary plastic package or boxes is forbidden to use.4.Use ionizer to neutralize the static charge during handling or operating.5.All surfaces and objects within 1 ft close to LEDs measure less than 100V.CleaningCleaningCleaningCleaningUse alcohol-based cleaning solvents such asIPA(isopropyl alcohol)to clean LEDsif necessary.SolderingSolderingSolderingSoldering1.Soldering condition refer to the draft“Soldering Profile Suggested”on page 1.2.Reflow soldering should not be donemore than 2 times.3.Manual solderingisonly suggested on repair and rework.The maximum soldering temperature shouldnot exceed 300C within 3 sec.And the maximum capacity of soldering ironis30W in power.4.During the soldering process,do not touch the lens at high temperature.5.Aftersoldering,any mechanical force on the lens or any excessive vibration shall not be accepted to apply,also thecircuit boardshall not be bent as well.OthersOthersOthersOthers1.The LEDs described here are intended to be used for ordinary electronic equipment(such as officeequipment,communication equipment and household applications).Consult HarvateksSales inadvance forthe applications in which exceptional reliabilityisrequired,particularly when the failure ormalfunction of the LEDs may directly jeopardize life or health.(such as in aviation,transportation,traffic controlequipment,medical and life support systems and safety devices).2.The light output from the high luminousintensity LEDs may cause injury to human eyes when vieweddirectly.3.The appearance and specifications of the product may be modified forimprovement without prior notice.