华威调光调色温LED球泡灯规格书(英文).pdf
ShenZhen hawinopto Co,;Ltd Diamond light 2.4G LED Bulb with Remote Control System Color temperature and brightness adjustable 1.1.Features and Functions It is a high-performance remote control LED bulb,adopting the wireless remote to control the switch and adjust the brightness.No extra wiring installation,simple and convenient.Adopting imported LED light sourceRefond 5730,so the power consumption is 20%of the traditional incandescent lamp,but the life span is over 10 times longer than the fluorescent lamp.Easy to install and use,safe and stable.The intelligent bulb help us to achieve the energy saving and environmental protection.Using the forging and stamping aluminum lamp body and increasing more fins to cycle air at same time,it helps us to successfully solve the heat sink trouble.The cover of LED Bulbs is made of imported high polymer nanometer material.The light transmittance is over 85%and very even.With the technology of the 2.4G high frequency for the wireless remote controller,it has the characteristics of low power consumption,long distance transmission,and strong anti-interference ability,high speed telecommunications,etc.The remote looks fashionable and elegant,with the function of night light mode and memory(that is to say,the previous settings will be resumed after the power on again).LED bulbs with lamp base E27 are widely used in living room,kitchen,hallway,etc.2.2.Technical Data Remote Dimension 1155220mm Working voltage 3V AAA Radio frequency 24002483.5MHz Modulation mode GFSK Emission power 6db Standby power consumption 5uA Material ABS Fabrication processing Multicolor printing&UV varnish Bulb Dimension 124x65mm Working voltage 85V265V 50/60HZ LED Quantity 24PCS LED Power 6W LED Type Refond 5730 Power factor 0.65 CRI 75 LED light effect 100 lm/W Color Temperature 3000K-6500K Maximum Luminous Flux in Total 600LM Telecontrol distance 2030 meters Working Temp-4060 Lamp base E27 3：Functions of Keys:4.Basic Function and Operation:1.Code matching and Code Clearing:the remote can work only after code matched with the LED bulb,the method is as follows:Please confirm the bulb installation and power connection first and choose the bulbs which you want to program with the remote,then switch off the power,after 10 seconds switch on the power again,please press this key on the upper side(channel-on)once(within 3 seconds),the moment you see the light is on and also the bulb blinks three time when its done.Please just repeat the above steps to program more bulbs with the remote as needed.Note:One bulb can only be programmed to one group of the same remote controller,and one remote can program the countless bulbs,but one bulb can only programmed with four remotes in max.2.Code clearing&Group Division：If the room layout change,or use methods change,you may need to change the previous group setting.You also need to clear the address code of the bulb before regrouping the bulbs.The method is as follows:please choose the bulb that you want to clear the code,switch off the power and press the“all-on”-button or“channel-on”button 5 times within 3 seconds when you switch the power on again after 10 seconds.If the light blinks 6 times,it indicates the code clearing is successful.You can match the code and regroup the bulbs as the code matching above.3.Night Light Mode：Press“all off”button,all bulbs are switched into night light mode at the same time.Press“channel-off”button of each group ,all bulbs of this group are switched into night light mode at the same time.Night light brightness is as2 of the highest brightness.5.Spectrum&Distribution Curve（6000-6500K）6.Attention 6.Attention 1.Please check whether the type of the lamp base is in accordance with the product before fixing.Please dont operate with the power on.2.Please do not put the bulb in the place with widely range metal area or with strong electromagnetic wave nearby,otherwise,the remote distance will be seriously affected.
