深圳市智炫显示科技有限公司高亮液晶屏规格书ZXXS065-L02.pdf

1/26 ZXXS065-L02 ()Preliminary Specifications (V)Final Specifications Module 6.5 Inch Color TFT-LCD Model Name ZXXS065-L02 Customer Date _ Checked&Approved by _ Note:This Specification is subject to change without notice.Approved by Date Debbie Chiu 2009/9/29 _ Prepared by David Hsing 2009/9/29 _ General Display Business Division/AU Optronics corporation ZXXS065-L02 2/26 ZXXS065-L02Contents 1.Operating Precautions.4 2.General Description.5 2.1 Display Characteristics.5 2.2 Optical Characteristics.6 3.Functional Block Diagram.9 4.Absolute Maximum Ratings.9 4.1 Absolute Ratings of TFT-LCD Module.9 4.2 Absolute Ratings of Environment.9 5.Electrical Characteristics.10 5.1 TFT-LCD Driving.10 5.2 Backlight Unit.12 6.Signal Characteristic.14 6.1 Pixel Format Image.14 6.2 Scanning Direction.14 6.3 The Input Data Format.15 6.4 TFT-LCD Interface Signal Description.16 6.5 TFT-LCD Interface Timing.17 6.6 CCFL Backlight Unit Interface.19 6.7 Power ON/OFF Sequence.19 7.Connector&Pin Assignment.21 7.1 TFT-LCD Signal(CN1):LCD Connector.21 7.2 Backlight Unit(CN2):Backlight Connector.21 7.3 PIN 1 Definition of CN1 and CN2.22 8.Reliability Test Criteria.23 9.Mechanical Characteristics.24 10.Label and Packaging.25 10.1 Shipping Label(on the rear side of TFT-LCD display).25 10.2 Carton Package.25 11 Safety.26 11.1 Sharp Edge Requirements.26 11.2 Materials.26 11.3 Capacitors.26 11.4 National Test Lab Requirement.26 3/26 ZXXS065-L02Record of Revision Version and Date Page Old description New Description Remark 0.1 July 17,2006 All First edition final specifications to all customers 0.2 Mar 10,2007 4 Revision&add 15,16,17,18 Section 1 5 Temperature Range Operating:-10 to+70 Temperature Range Operating:-20 to+70 Section 2.1 10 Absolute Ratings of Environment Operating Temperature:Min-10 Absolute Ratings of Environment Operating Temperature:Min-20 Section 4.2 5 Support color:16.2M(RGB 8-bit)Support color:16.2M(RGB 6-bits+FRC)Section 2 5 No description The most suitable view angle:6 oclock Section 2.1 9 No description Absolute Ratings of TFT-LCD Module CCFL Current:6.5 mA(rms)Section 4.1 11 No description Add Input Voltage Characteristics for DPS and SEL68 Section 5.1.2 12 Revise Parameter Guideline for CCFL Section 5.2.1 12,13 Revise Note 1,Note 4 Section 5.2.1 17 No description Add H/V mode timing characteristics Section 6.5.1 17 No description Add Note 2,Note 3 Section 6.5.1 18 No description Add H/V mode input timing diagram Section 6.5.2 19 No description Add CCFL Backlight Unit Interface Section 6.6 21 Revise PIN 1 definition of CN1 and CN2 Section 7.3 22 Cold Start Test:-10?Cold Start Test:-20?Section 8 22 No description Add Note 2 Section 8 0.3 Jan 18,2008 23 Revise 2D drawing Section 9 1.0 Oct 06,2008 24 Use V0 on shipping lable.Use V.0 on shipping label.Section 10.1 6 View angle(Typ.):70/70/60/60 View angle(Min.):60/60/50/50 View angle(Typ.):80/80/70/70 View angle(Min.):70/70/60/60 Section 2.2 1.1 Dec 17,2008 10 Power Specification IDD:Max.=No definition PDD:Max.=No definition Power Specification IDD:Max.=265 mA PDD:Max.=0.87 W Section 5.1.1 9 Absolute Ratings of Environment Add Note 2 Section 4.2 1.2 Sep 29,2009 23 Mechanical Characteristics Note1:Self-taping Screw Mechanical Characteristics Note1:User mounting hole.Section 9 4/26 ZXXS065-L02 1.Operating Precautions 1)Display area(Polarizer)of TFT-LCD Module is easily to be damaged,please be cautious and not to scratch it.2)Be sure to power off your machine before connecting or disconnecting your signal cable to TFT-LCD Module.3)Wipe off water drop on display area immediately.Long contact with water may cause discoloration or spots.4)When the panel surface is soiled,wipe it with absorbent cotton or soft cloth.5)Display area(Glass)of TFT-LCD Module may be broken or cracked if bump Module against hard object.6)To avoid ESD(Electro Static Discharde)damage,be sure to ground yourself before handling TFT-LCD Module.7)Do not open nor modify the TFT-LCD Module assembly.8)Do not press the reflector sheet at the back of the module to any direction.9)In case if a TFT-LCD Module has to be put back into the packing container slot after it was taken out from the container,do not press the center of the CCFL Reflector edge.Instead,press at the far ends of the CCFL Reflector edge softly.Otherwise the TFT-LCD Module may be damaged.10)When inserting or removing of your signal cable to TFT-LCD Module,be sure not to apply abnormal force(rotate,tiltetc.)to the Connector of the TFT-LCD Module.11)TFT-LCD Module is not allowed to be twisted&bent even force is added on module in a very short time.Please design your display product well to avoid external force applying to module by end-user directly.12)Cold cathode fluorescent lamp(CCFL)in TFT-LCD Module contains a small amount of mercury.Please follow local ordinances or regulations for disposal.13)Small amount of materials having no flammability grade is used in the TFT-LCD Module.The TFT-LCD Module should be supplied by power complied with requirements of Limited Power Source(IEC60950 or UL1950),or be applied exemption.14)The CCFL in TFT-LCD Module should be supplied by inverter complied with Limited Current Circuit(IEC60950 or UL1950).Do not connect the CCFL with Hazardous Voltage Circuit.15)Severe temperature condition may result in different luminance,response time and lamp ignition voltage.16)Continuous operating TFT-LCD Module under low temperature environment may accelerate lamp exhaustion and reduce luminance dramatically.17)The data on this specification sheet is applicable when TFT-LCD Module is placed in landscape position.18)Continuous displaying fixed pattern may induce image sticking.Its recommended to use screen saver or moving content periodically if fixed pattern is displayed on the screen.5/26 ZXXS065-L02 2.General Description ZXXS065-L02is designed for industrial display applications with VGA(640 x RGB x 480)resolution and 16.2M(RGB 6-bits+FRC)or 262k colors(RGB 6-bits).It is composed of a TFT-LCD panel,driver ICs,control and power supply circuits and a backlight unit.G065VN01 V0 offers LVDS interface for display signal input.Inverter board of backlight is not included.2.1 Display Characteristics The following items are G065VN01 V0 characteristics summary at25?condition.Items Unit Specifications Screen Diagonal inch 6.5 Active Area mm 132.48(H)x 99.36(V)Pixels H x V 640 x3(RGB)x 480 Pixel Pitch mm 0.207 x 0.207 Pixel Arrangement R.G.B.Vertical Stripe Display Mode TN,Normally White Nominal Input Voltage VDD V 3.3 typ.Typical Power Consumption W 9W(IRCFL=5mA)All black pattern Weight Grams 200g(typ.)Physical Size mm 153.0(H)x 118.0(V)x 10.7(D)(typ.)Electrical Interface 1 channel LVDS Surface Treatment Anti-glare,Hardness 3H Support Color 16.2M/262K colors The most suitable view angle 6 oclock Temperature Range Operating Storage(Non-Operating)oC oC -20 to+70-20 to+80 RoHS Compliance RoHS Compliance 6/26 ZXXS065-L022.2 Optical Characteristics Theopticalcharacteristicsaremeasuredunderstableconditionsat25(RoomTemperature).Item Unit Conditions Min.Typ.Max.Note IRCFL=5.0mA(center point)400 1200-White Luminance cd/m2 1 5 Points-1.25 Uniformity%13 Points-1.67 1,2,3,4 Contrast Ratio 300 600-5 msec Rising-15 20 msec Falling-10 15 Response Time msec Raising+Falling-25 35 6 degree degree Horizontal (Right)CR=10 (Left)70 70 80 80-Viewing Angle degree degree Vertical (Upper)CR=10 (Lower)60 60 70 70-7 Red x 0.590 0.620 0.650 Red y 0.320 0.350 0.380 Green x 0.275 0.305 0.335 Green y 0.550 0.580 0.610 Blue x 0.115 0.145 0.175 Blue y 0.085 0.115 0.145 White x 0.283 0.313 0.343 Color/Chromaticity Coordinates (CIE 1931)White y 0.299 0.329 0.359 Color Gamut%50 55-Note 1:Measurement method Equipment Pattern Generator,Power Supply,Digital Voltmeter,Luminance meter(SR_3 or equivalent)Aperture 1with50cmviewingdistance Test Point Center Environment 5.5 mA)shortens lamp life time dramatically.Note 5:The display is with dual lamp design,and the CCFL operation current in above table is for each lamp.14/26 ZXXS065-L026.Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship between input signal and LCD pixel format.6.2 Scanning Direction The following figures show the image seen from the front view.The arrow indicates the direction of scan.Fig.1 Normal scan(Pin8,DPS=Low or NC)Fig.2 Reverse scan(Pin8,DPS=High)Note 1:TFT-LCD interface signal description is shown in section 6.4.15/26 ZXXS065-L026.3 The Input Data Format SEL68=”High”or“NC”for 6 bits LVDS Input G0R5R4R3R2 R1R0DEVSHSB5B4 B3B2B1B0G5G4G3 G2G1RxCLKINRxIN1RxIN2RxIN3 SEL68=“Low”for 8 bits LVDS Input G0R5R4R3R2 R1R0RSVB7B6G7G6 R7R6DEVSHSB5B4 B3B2B1B0G5G4G3 G2G1RxCLKINRxIN1RxIN2RxIN3RxIN4 Signal Name Description Remark R7 R6 R5 R4 R3 R2 R1 R0 Red Data 7 Red Data 6 Red Data 5 Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0 Red-pixel Data For 8Bits LVDS input MSB:R7;LSB:R0 For 6Bits LVDS input MSB:R5;LSB:R0 G7 G6 G5 G4 G3 G2 G1 G0 Green Data 7 Green Data 6 Green Data 5 Green Data 4 Green Data 3 Green Data 2 Green Data 1 Green Data 0 Green-pixel Data For 8Bits LVDS input MSB:G7;LSB:G0 For 6Bits LVDS input MSB:G5;LSB:G0 B7 B6 B5 B4 B3 B2 B1 B0 Blue Data 7 Blue Data 6 Blue Data 5 Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0 Blue-pixel Data For 8Bits LVDS input MSB:B7;LSB:B0 For 6Bits LVDS input MSB:B5;LSB:B0 RxCLKIN LVDS Data Clock DE Data Enable Signal When the signal is high,the pixel data shall be valid to be displayed.VS Vertical Synchronous Signal HS Horizontal Synchronous Signal RSV Reserved Signal“High”or“Low”is acceptable Note 1:Output signals from any system shall be low or Hi-Z state when VDD is off.16/26 ZXXS065-L026.4 TFT-LCD Interface Signal Description G065VN01 V0 TFT-LCD module includes LVDS receiver.LVDS is a differential signal technology for high-speed data transfer LCD interface.LVDS Transmitter shall be THC63LVDM83A(THINE)or equivalent.Note 1:Input signals shall be in low status when VDD is off.Pin No.Symbol Pin Description 1 GND Ground 2 GND Ground 3 RxIN4+LVDS differential input(Red 6-Red 7,Green 6-Green 7,Blue 6-Blue 7,RSV)NC for 6bit LVDS input.4 NC No connection 5 RxIN4-LVDS differential input(Red 6-Red 7,Green 6-Green 7,Blue 6-Blue 7,RSV)NC for 6bit LVDS input.6 NC No connection 7 GND Ground 8 DPS Selection of scan direction DPS=Low or NC,normal scan.DPS=High,reverse scan.9 RxCLKIN+LVDS differential clock input 10 NC No connection 11 RxCLKIN-LVDS differential clock input 12 NC No connection 13 GND Ground 14 GND Ground 15 RxIN3+LVDS differential input(Blue2-Blue5,Hsync,Vsync,DE)16 GND Ground 17 RxIN3-LVDS differential input(Blue2-Blue5,Hsync,Vsync,DE)18 NC No connection 19 GND Ground 20 NC No connection 21 RxIN2+LVDS differential input(Green1-Green5,Blue0-Blue1)22 NC No connection 23 RxIN2-LVDS differential input(Green1-Green5,Blue0-Blue1)24 NC No connection 25 GND Ground 26 SEL68 Selection for either 6bit or 8bit LVDS input:SEL68=”High”or“NC”,accepts 6bit LVDS data input;SEL68=”Low”,accepts 8bit LVDS data input.27 RxIN1+LVDS differential input(Red0-Red5,Green0)28 VDD Power supply,3.3V(typical)29 RxIN1-LVDS differential input(Red0-Red5,Green0)30 VDD Power supply,3.3V(typical)31 GND Ground 17/26 ZXXS065-L026.5 TFT-LCD Interface Timing 6.5.1 Timing Characteristics DE mode Signal Parameter Symbol Min.Typ.Max.Unit Remark Clock Timing Clock frequency(DOTCLK)1/TCLOCK 20 25.2 50 MHz Note1,2 Period TH 770 800 1070 Active THD 640 640 640 Hsync Timing Horizontal Section Blanking THB 130 160 430 TCLOCK Note1,2 Period TV 520 525 622 Active TVD 480 480 480 Vsync Timing Vertical Section Blanking TVB 40 45 142 TLINE Note1,2 H/V mode Signal Parameter Symbol Min.Typ.Max.Unit Remark Clock Timing Clock frequency(DOTCLK)1/TCLOCK 20 25.2 50 MHz Note 3 Display period THSD 640 Front porch THSF 30 60 330 Hsync pulse width+Back porch THSW+THSB 100 Hsync Timing Horizontal Section Hsync Period THS 770 800 1070 TCLOCK Note 3 Display period TVSD 480 Front porch TVSF 5 10 107 Vsync pulse width+Back porch TVSW+TVSB 35 Vsync Timing Vertical Section Vsync Period TVS 520 525 622 TLINE Note 3 Note 1:Recommended frame rate is 60 Hz.Note 2:G065VN01 V0 TFT-LCD Module can support DE&H/V mode.When DE and H/V signal are existed simultaneously,G065VN01 V0 TFT-LCD Module is operated in DE mode only.Note 3:H/V mode is negative polarity.18/26 ZXXS065-L026.5.2 DE&H/V Mode Input Timing Diagram DOTCLKDE TH THB THD DE TV TVB TVD Input Timing Definition(DE Mode)TCLOCK InputDataPixel1Pixel2Pixel3PixelN-1PixelNInvaildDataInvaildDataPixel1 19/26 ZXXS065-L02 6.6 CCFL Backlight Unit Interface Pin No.Cable color Symbol Pin Description 1 Pink Hot1 Lamp High Voltage 2 Pink Hot2 Lamp High Voltage 3 NC No Connection 4 White Cold1 Lamp Low Voltage 6.7 Power ON/OFF Sequence VDD power,LCD interface signals and backlight on/off sequence are shown in the following chart.Signals from any system shall be Hi-Z state or low level when VDD is off.Power ON/OFF sequence timing Value Parameter Min.Typ.Max.Units T1 0.5-10 ms T2 0-50 ms T3 180-ms T4 180-ms T5 0-50 ms T6 0-10 ms T7 500-ms ON/OFF sequence should be applied to avoid abnormal function in the display.Please make sure to turn off the power when T7 T5 T2 T3 VALID DATA T1 1090%10%90%T4 T6 Power Supply VDD LVDS Signal Backlight On 20/26 ZXXS065-L02you plug the cable into the input connector or pull the cable out of the connector.21/26 ZXXS065-L027.Connector&Pin Assignment 7.1 TFT-LCD Signal(CN1):LCD Connector Connector Name/Designation Signal Connector Manufacturer Hirose or compatible Connector Model Number DF9B-31P-1V or compatible Mating Connecter Model Number DF9B-31S-1V or compatible Pin#Symbol Pin#Symbol Pin#Symbol 1 GND 12 NC 23 RxIN2-2 GND 13 GND 24 NC 3 RxIN4+14 GND 25 GND 4 NC 15 RxIN3+26 SEL68 5 RxIN4-16 GND 27 RxIN1+6 NC 17 RxIN3-28 VDD 7 GND 18 NC 29 RxIN1-8 DPS 19 GND 30 VDD 9 RxCLKIN+20 NC 31 GND 10 NC 21 RxIN2+11 RxCLKIN-22 NC 7.2 Backlight Unit(CN2):Backlight Connector Connector Name/Designation Lamp Connector Manufacturer JST or compatible Connector Model Number BHR-04VS-1 or compatible Mating Connecter Model Number SM04(4.0)B-BHS-1-TB or compatible Pin No.Symbol 1 Hot1 2 Hot2 3 NC 4 Cold1 22/26 ZXXS065-L027.3 PIN 1 Definition of CN1 and CN2 23/26 ZXXS065-L028.Reliability Test Criteria Items Required Condition Note Temperature Humidity Bias 40T/90%,300Hr Note 2 High Temperature Operation 70T,300Hr Note 2 Low Temperature Operation-20T,300Hr Note 2 High Temperature Storage 80T,300hours Note 2 Low Temperature Storage-20T,300hours Note 2 Thermal Shock Test-20T/30min,60T/30min,100cycles Note 2 Hot Start Test 70T/1Hr(min.),power on/off per 5 minutes,repeat 5 times Note 2 Cold Start Test-20T/1Hr(min.),power on/off per 5 minutes,repeat 5 times Note 2 Shock Test (Non-Operating)50G,11ms,Half-sine wave,(X,Y,Z)Note 2 Vibration Test(Non-Operating)1.5G,5050050Hz,Sine wave,30mins/axis,3 direction(X,Y,Z)Note 2 ESD Contact Discharge:8KV,150pF(330)1sec,8 points,25 times/point Air Discharge:15KV,150pF(330)1sec,8 points,25 times/point Note 1,2 Attitude Test