富士康~群创7寸TN92模组规格书AT070TN92 P(V01)_20091.pdf

The copyright belongs to InnoLux.Any unauthorized use is prohibited.INNOLUX DISPLAY CORPORATION LCD MODULE SPECIFICATION Customer:Model Name:AT070TN92 SPEC NO.:A070-92-TT-01 Date:2009/01/12 Version:01 Preliminary Specification Final Specification For Customers Acceptance Approved by Comment Approved by Reviewed by Prepared by Joe Lin 2009/02/12 James Yu Jack Huang Charlie Chou 2009/02/12 David Lee 2009/02/11 The copyright belongs to InnoLux.Any unauthorized use is prohibited.InnoLux copyright 2004 All rights reserved,Copying forbidden.Record of Revision Version Revise Date Page Content Pre-Spec.01 2009/01/12 Initial Release INNOLUX The copyright belongs to InnoLux.Any unauthorized use is prohibited.Contents 1.General Specifications.1 2.Pin Assignment.2 3.Operation Specifications.5 3.1.Absolute Maximum Rating.5 3.1.1.Typical Operation Conditions.6 3.1.2.Current Consumption.7 3.1.3.Backlight Driving Conditions.7 3.2.Power Sequence.8 3.3.Timing Characteristics.9 3.3.1.AC Electrical Characteristics.9 3.3.2.Data Input Format.10 3.3.3.Timing.11 4.Optical Specifications.12 5.Reliability Test Items.16 6.General Precautions.17 6.1.Safety.17 6.2.Handling.17 6.3.Static Electricity.17 6.4.Storage.17 6.5.Cleaning.17 7.Mechanical Drawing.18 8.Package Drawing.19 8.1 Packaging Material Table.19 8.2 Packaging Quantity.19 8.3 Packaging Drawing.20 INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:1/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.1.General Specifications No.Item Specification Remark 1 LCD size 7.0 inch(Diagonal)2 Driver element a-Si TFT active matrix 3 Resolution 800 3(RGB)480 4 Display mode Normally White,Transmissive 5 Dot pitch 0.0642(W)0.1790(H)mm 6 Active area 154.08(W)85.92(H)mm 7 Module size 164.9(W)100.0(H)5.7(D)mm Note 1 8 Surface treatment Anti-Glare 9 Color arrangement RGB-stripe 10 Interface Digital 11 Backlight power consumption TBD 12 Panel power consumption TBD 13 Weight TBD Note 1:Refer to Mechanical Drawing.INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:2/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.2.Pin Assignment TFT LCD Panel Driving Section FPC Connector is used for the module electronics interface.The recommended model is FH12A-50S-0.5SH manufactured by Hirose.Pin No.Symbol I/O Function Remark 1 VLED+P Power for LED backlight(Anode)2 VLED+P Power for LED backlight(Anode)3 VLED-P Power for LED backlight(Cathode)4 VLED-P Power for LED backlight(Cathode)5 GND P Power ground 6 VCOM I Common voltage 7 DVDD P Power for Digital Circuit 8 MODE I DE/SYNC mode select Note 1 9 DE I Data Input Enable 10 VS I Vertical Sync Input 11 HS I Horizontal Sync Input 12 B7 I Blue data(MSB)13 B6 I Blue data 14 B5 I Blue data 15 B4 I Blue data 16 B3 I Blue data 17 B2 I Blue data 18 B1 I Blue data Note 2 19 B0 I Blue data(LSB)Note 2 20 G7 I Green data(MSB)21 G6 I Green data 22 G5 I Green data 23 G4 I Green data 24 G3 I Green data 25 G2 I Green data INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:3/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.26 G1 I Green data Note 2 27 G0 I Green data(LSB)Note 2 28 R7 I Red data(MSB)29 R6 I Red data 30 R5 I Red data 31 R4 I Red data 32 R3 I Red data 33 R2 I Red data 34 R1 I Red data Note 2 35 R0 I Red data(LSB)Note 2 36 GND P Power Ground 37 DCLK I Sample clock Note 3 38 GND P Power Ground 39 L/R I Left/right selection Note 4,5 40 U/D I Up/down selection Note 4,5 41 VGH P Gate ON Voltage 42 VGL P Gate OFF Voltage 43 AVDD P Power for Analog Circuit 44 RESET I Global reset pin.Note 6 45 NC-No connection 46 VCOM I Common Voltage 47 DITHB I Dithering function Note 7 48 GND P Power Ground 49 NC-No connection 50 NC-No connection I:input,O:output,P:Power Note 1:DE/SYNC mode select.Normally pull high.When select DE mode,MODE=”1”,VS and HS must pull high.When select SYNC mode,MODE=”0”,DE must be grounded.Note 2:When input 18 bits RGB data,the two low bits of R,G and B data must be grounded.Note 3:Data shall be latched at the falling edge of DCLK.INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:4/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.Note 4:Selection of scanning mode Setting of scan control input U/D L/R Scanning direction GND DVDD Up to down,left to right DVDD GND Down to up,right to left GND GND Up to down,right to left DVDD DVDD Down to up,left to right Note 5:Definition of scanning direction.Refer to the figure as below:Note 6:Global reset pin.Active low to enter reset state.Suggest to connect with an RC reset circuit for stability.Normally pull high.Note 7:Dithering function enable control,normally pull high.When DITHB=”1”,Disable internal dithering function,When DITHB=”0”,Enable internal dithering function,Right Left Down Up INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:5/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.3.Operation Specifications 3.1.Absolute Maximum Ratings (Note 1)Values Item Symbol Min.Max.Unit Remark DVDD-0.3 5.0 V AVDD 6.5 13.5 V VGH-0.3 40.0 V VGL-20.0 0.3 V Power voltage VGH-VGL-40.0 V Operation Temperature TOP-20 70 Storage Temperature TST-30 80 LED Reverse Voltage VR-1.2 V Each LED Note 2 LED Forward Current IF-25 mA Each LED Note 1:The absolute maximum rating values of this product are not allowed to be exceeded at any times.Should a module be used with any of the absolute maximum ratings exceeded,the characteristics of the module may not be recovered,or in an extreme case,the module may be permanently destroyed.Note 2:VR Conditions:Zener Diode 20mA INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:6/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.3.1.1.Typical Operation Conditions (Note 1)Values Item Symbol Min.Typ.Max.Unit Remark DVDD 3.0 3.3 3.6 V Note 2 AVDD(10.2)(10.4)(10.6)V VGH(15.3)(16.0)(16.7)V Power voltage VGL(-7.7)(-7.0)(-6.3)V Input signal voltage VCOM-TBD-V Input logic high voltage VIH 0.7 DVDD-DVDD V Input logic low voltage VIL 0-0.3 DVDD V Note 3 Note 1:Be sure to apply DVDD and VGL to the LCD first,and then apply VGH.Note 2:DVDD setting should match the signals output voltage(refer to Note 3)of customers system board.Note 3:DCLK,HS,VS,RESET,U/D,L/R,DE,R0R7,G0G7,B0B7,MODE,DITHB.INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:7/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.3.1.2.Current Consumption Values Item Symbol Min.Typ.Max.Unit Remark IGH-TBD-mA VGH=17.0V IGL-TBD-mA VGL=-5.0V IDVDD-TBD-mA DVDD=3.3V Current for Driver IAVDD-TBD-mA AVDD=10.4V 3.1.3.Backlight Driving Conditions Values Item Symbol Min.Typ.Max.Unit Remark Voltage for LED backlight VL(9.3)(9.9)(10.5)V Note 1 Current for LED backlight IL(170)(180)(200)mA LED life time-20,000-Hr Note 2 Note 1:The LED Supply Voltage is defined by the number of LED at Ta=25 and IL=180mA.Note 2:The“LED life time”is defined as the module brightness decrease to 50%original brightness at Ta=25 and IL=180mA.The LED lifetime could be decreased if operating IL is lager than 180mA.INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:8/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.3.2.Power Sequence a.Power on:b.Power off:Note:Data include R0R7,B0B7,GOG7,U/D,L/R,DCLK,HS,VS,DE.DVDDVGLVGHDataB/L B/LDataVGHVGLDVDD INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:9/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.3.3.Timing Characteristics 3.3.1.AC Electrical Characteristics Values Item Symbol Min.Typ.Max.Unit Remark HS setup time Thst 8-ns HS hold time Thhd 8-ns VS setup time Tvst 8-ns VS hold time Tvhd 8-ns Data setup time Tdsu 8-ns Data hole time Tdhd 8-ns DE setup time Tesu 8-ns DE hole time Tehd 8-ns DVDD Power On Slew rate TPOR-20 ms From 0 to 90%DVDD RESET pulse width TRst 1-ms DCLK cycle time Tcoh 20-ns DCLK pulse duty Tcwh 40 50 60%INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:10/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.3.3.2.Data Input Format INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:11/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.3.3.3.Timing Values Item Symbol Min.Typ.Max.Unit Remark Horizontal Display Area thd-800-DCLK DCLK Frequency fclk 26.4 33.3 46.8 MHz One Horizontal Line th 862 1056 1200 DCLK HS pulse width thpw 1-40 DCLK HS Blanking thb 46 46 46 DCLK HS Front Porch thfp 16 210 354 DCLK Values Item Symbol Min.Typ.Max.Unit Remark Vertical Display Area tvd-480-TH VS period time tv 510 525 650 TH VS pulse width tvpw 1-20 TH VS Blanking tvb 23 23 23 TH VS Front Porch tvfp 7 22 147 TH INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:12/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.4.Optical Specifications Values Item Symbol Condition Min.Typ.Max.Unit Remark L=180(9 oclock)60 70-R=0(3 oclock)60 70-T=90(12 oclock)40 50-Viewing angle(CR 10)B=270(6 oclock)60 70-degree Note 1 TON-10 20 msec Note 3 Response time TOFF-15 30 msec Note 3 Contrast ratio CR 400 500-Note 4 WX 0.26 0.31 0.36-Color chromaticity WY 0.28 0.33 0.38-Note 2 Note 5 Note 6 Luminance L 200 250-cd/m Note 6 Luminance uniformity YU Normal=0 70 75-%Note 7 Test Conditions:1.DVDD=3.3V,IL=180mA(Backlight current),the ambient temperature is 25.2.The test systems refer to Note 2.INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:13/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.Note 1:Definition of viewing angle range Fig.4-1 Definition of viewing angle Note 2:Definition of optical measurement system.The optical characteristics should be measured in dark room.After 30 minutes operation,the optical properties are measured at the center point of the LCD screen.(Response time is measured by Photo detector TOPCON BM-7,other items are measured by BM-5A/Field of view:1/Height:500mm.)Fig.4-2 Optical measurement system setup Normal line=0 Photo detector=90 12 oclock direction=270 6 oclock direction=0=180 Active Area 500mm LCM Normal line=0=90 12 oclock direction=270 6 oclock direction=0=180 Active Area L T B R LCM INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:14/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.Note 3:Definition of Response time The response time is defined as the LCD optical switching time interval between“White”state and“Black”state.Rise time(TON)is the time between photo detector output intensity changed from 90%to 10%.And fall time(TOFF)is the time between photo detector output intensity changed from 10%to 90%.Fig.4-3 Definition of response time Note 4:Definition of contrast ratio state Black the on LCD whenmeasured Luminancestate White the on LCD whenmeasured Luminance(CR)ratio Contrast=Note 5:Definition of color chromaticity(CIE1931)Color coordinates measured at center point of LCD.Note 6:All input terminals LCD panel must be ground while measuring the center area of the panel.The LED driving condition is IL=180mA.100%90%10%0%Photo detector output(Relative value)TON TOFF White(TFT OFF)Black(TFT ON)White(TFT OFF)INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:15/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.Note 7:Definition of Luminance Uniformity Active area is divided into 9 measuring areas(Refer to Fig.4-4).Every measuring point is placed at the center of each measuring area.maxminBB(Yu)Uniformity Luminance=L-Active area length W-Active area width WW/3W/3W/6L/3L/3L/6L Fig.4-4 Definition of measuring points Bmax:The measured maximum luminance of all measurement position.Bmin:The measured minimum luminance of all measurement position.INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:16/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.5.Reliability Test Items(Note3)Item Test Conditions Remark High Temperature Storage Ta=80 240hrs Note 1，Note 4 Low Temperature Storage Ta=-30 240hrs Note 1，Note 4 High Temperature Operation Ts=70 240hrs Note 2，Note 4 Low Temperature Operation Ta=-20 240hrs Note 1，Note 4 Operate at High Temperature and Humidity+60,90%RH 240hrs Note 4 Thermal Shock-30/30 min +80/30 min for a total 100 cycles,Start with cold temperature and end with high temperature.Note 4 Vibration Test Frequency range:1055Hz Stroke:1.5mm Sweep:10Hz55Hz10Hz 2 hours for each direction of X.Y.Z.(6 hours for total)Mechanical Shock 100G 6ms,X,Y,Z 3 times for each direction Package Vibration Test Random Vibration:0.015G*G/Hz from 5-200HZ,-6dB/Octave from 200-500HZ 2 hours for each direction of X.Y.Z.(6 hours for total)Package Drop Test Height:60 cm 1 corner,3 edges,6 surfaces Electro Static Discharge 2KV,Human Body Mode,100pF/1500 Note 1:Ta is the ambient temperature of samples.Note 2:Ts is the temperature of panels surface.Note 3:In the standard condition,there shall be no practical problem that may affect the display function.After the reliability test,the product only guarantees operation,but dont guarantee all of the cosmetic specification.Note 4:Before cosmetic and function test,the product must have enough recovery time,at least 2 hours at room temperature.INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:17/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.6.General Precautions 6.1.Safety Liquid crystal is poisonous.Do not put it in your mouth.If liquid crystal touches your skin or clothes,wash it off immediately by using soap and water.6.2.Handling 1.The LCD panel is plate glass.Do not subject the panel to mechanical shock or to excessive force on its surface.2.The polarizer attached to the display is easily damaged.Please handle it carefully to avoid scratch or other damages.3.To avoid contamination on the display surface,do not touch the module surface with bare hands.4.Keep a space so that the LCD panels do not touch other components.5.Put cover board such as acrylic board on the surface of LCD panel to protect panel from damages.6.Transparent electrodes may be disconnected if you use the LCD panel under environmental conditions where the condensation of dew occurs.7.Do not leave module in direct sunlight to avoid malfunction of the ICs.6.3.Static Electricity 1.Be sure to ground module before turning on power or operating module.2.Do not apply voltage which exceeds the absolute maximum rating value.6.4.Storage 1.Store the module in a dark room where must keep at 2510 and 65%RH or less.2.Do not store the module in surroundings containing organic solvent or corrosive gas.3.Store the module in an anti-electrostatic container or bag.6.5.Cleaning 1.Do not wipe the polarizer with dry cloth.It might cause scratch.2.Only use a soft sloth with IPA to wipe the polarizer,other chemicals might permanent damage to the polarizer.INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:18/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.7.Mechanical Drawing INNOLUX SPEC NO.:A070-92-TT-01 Date:2009/01/12 Page:19/20 The copyright belongs to InnoLux.Any unauthorized use is prohibited.8.Package Drawing 8.1.Packaging Material Table No.Item Model(Material)Dime