台虎钳使用说明书-中英文.pdf

精品文档 1欢迎下载 台虎钳使用说明书 Bench vice operati ng in structi on 1、用途 application:台虎钳是用来加持工件的通用夹具。装置在工作台上，用以夹稳 加工工件，为钳工车间必备工具。转盘式的钳体可旋转，使工件旋转 到合适的工作位置。钳工的大部分工作都是 在台钳上完成的，比如锯，锂，錾，以及零件的装配和拆卸。台虎钳的规格以钳口的宽度表示，本次提供台虎钳规格为 200mm Bench vice is used to clamp workpieces.It is in stalled on the work stati ons to clamp the workpieces.It is an necessary tool in the schlosserei.Rotating disc type clamp body can revolve so that make the workpiece rotate to the suitable place.Most work of fitter are fini shed on the bench vice.For example the saw,the file,the chisel and comp onents in stalli ng and disma ntl ing.The specification of bench vice is expressed by the width 精品文档 2欢迎下载 of jaw.The bench vice we supplied is 200mm.2、使用方法 operating instruction 台虎钳在钳台上安装时，必须使固定钳身的工作面处于钳台 边缘 台虎钳 以外，以保证夹持长条形工件时，工件的下端不受钳台边缘的阻 碍。Whe n the bench vice is in stalled on the vice sta nd,you n eed make the work ing face on the vice sta nd outside edge.So that when the bench vice clamps the long workpiece,it will be not hampered by vice sta nd.在钳桌装上台虎钳后操作者工作时的高度比较合适，一般多 以钳口高度恰好与肘齐平为宜，即肘放在台虎钳最高点半握拳，拳刚好抵下颚，钳桌的长度和宽度则随工作而定。The height of operator working will be suitable because the bench vice is in stalled on the work ben ch.Usually the jaw height is flushed with elbow just right.This is ok.精品文档 3欢迎下载 Put the elbow on the bench vice peak and half clenched fists精品文档 4欢迎下载 that the fist just support the man dible.Len gth and width of work bench will be decided by the work.3、注意事项 cautions（1）夹紧工件时要松紧适当，只能用手板紧手柄，不得借 助其他工具加力。Appropriate degree of tight ness whe n clamp the workpiece.Just tight the hand sha nk by the hand only.Do not add strength with the help of other tools.（2）强力作业时，应尽量使力朝向固定钳身。Whe n work stron gly,you n eed try your best to make stre ngth facing to clamp body.（3）不许在活动钳身和光滑平面上敲击作业。Do not knocking on the clamp body and smooth surface.（4）对丝杠、螺母等活动表面应经常清洗、润滑，以防生 锈。Clea n and lubricate the surface of lead screw and nut.So that it will not rust.精品文档 5欢迎下载 欢迎您的下载，资料仅供参考!致力为企业和个人提供合同协议，策划案计划书，学习资料等等 打造全网一站式需求