电梯专业英语词汇.docx

电梯专业英语词汇  abbreviation 缩语  abnormal "不正常的,反常的"  abnormality monitoring 异常监听  abrasion 磨损  abrasion resistant 耐磨性  abrasive cloth 砂布  absorb 吸收  absorber 减振器  AC drive 交流拖动  AC feedback control 交流反馈控制  AC motor 交流电机  AC servo 交流伺服  AC servo motor 交流伺服电机  AC single speed 交流单速  AC two speed 交流双速  AC two speed motor 交流双速电动机  AC variale speed 交流调速  AC(alternating current) 交流电  acanning cycle 扫描周期，扫描循环  acceleration control system 加速度控制系统  acceleration(accel)rate 加速器  accelerator 加速器  acceptance of lift 电梯验收  acceptance period 验收阶段  acceptance test 验收试验  acceptanec certificate 验收证书  access door 检修门  access forbidden 禁止入内  access lift 通道电梯  access security 通道防卫  access switch "通道开关,维修用开关"  access way 进出通道  accessibility "可通达性,接近的,难易程度"  accessible 允许进入  accessible space 允许进入的场地  accessory "配件,附件"  accident 事故  accident insurance 事故保险  accident prevention 事故预防  accidental contact 触电  accidental operation 误操作  accordion door 折叠门  accumulation 累积  accumulator 蓄电池  AC-GL machine 交流无齿曳引机  acoustic "听觉的,声音的"  acrew die 板牙  activate "启动,触发"  active mode 主动模式  actual condition "实际状况,实际条件"  actual load 实际载荷  actual state 实际状况  actual value 实际值  actuate "开动,操作,激励"  actuating linkege 操作连杆  actuating magnet 操作磁铁  actuation time 动作时间  actuator "操纵机构,激励器,螺线管"  actuator bracket 调节器支架 actuator plate 调节板  ACVF drive 交流调频拖动  ACVF system 交流调频系统  ACVF(AC varible frequency) 交流调速  ACVV dirve 交流调压拖动  ACVV system 交流调压系统  ACVV(AC varible voltage) 交流调压  adaptation "适应,匹配"  adapter PCB 选通脉冲印刷电路板  adapter(adapator) 适配器  adapting 选配  adaptive control system 自适应能力控制系统  addendum "齿顶高,附录"  addendum circle 外圆  adding working drawing 附加加工图  addition "附加物,加法"  additional materials 附加材料  address 地址  adhesion "胶,粘合胶"  adhesion protective oil 防粘油  adhesive foil 胶粘薄膜  adhesive tape 胶带  adjacent 邻近的  adjacent car "相邻轿厢,相邻电梯"  adjacent entrance 相邻出入口  adjusment 调试  adjustable condensor 可变电容器  adjustable resistance 可调电阻  adjustable spanner 可调扳手  adjustable speed electric drive 调速电力拖动  adjustable wrench "活动扳手,可调扳手"  adjusting screw 调节螺丝  adjustor 调试员  administation overjhead rate 管理费用标准  administration cost 管理成本  administration expenses 管理费用  advance door opening 提前开门  advance payment 预付款  advanced "提前的,先进的"  advanced carriage 超前拖板(选层器)  advancing position reference value 超前位置参考值  aerial cableway "空中缆车,架空索道"  aerial ropeway "空中缆车,架空索道"  aerial tramway "空中缆车,架空索道"  aesthetic 美观  after sales service 售后服务  agency 代理  agenda 议程  air cord (门机用)航空钢丝绳  air purifier 空气滤清剂  air ventilator 通风管  air-bleed 空气分泄器  airborne noise 空气传播噪声  air-condition 空调  air-gap 气隙  alarm 警报  alarm bell 警铃  alarm button 警铃按钮  alarm buzzer 警报蜂鸣器  alarm circuit 警报电路  alarm system 警报系统 ALC(autoclaved light-weight concrete) 蒸压轻质混凝土  alcove arrangement 电梯U型排列法  algorithm 算法规则系统  align 校正  aligning template 校正样板  alignment 校正  alignment gauge 校正量规  alkali 碱  all-computer-controlled 计算机全控的  allocation "分配,分派"  allocation of landing call 层站呼梯指令分配  allowance "允用误差,加工余量"  allowble stress for temporary load 允许暂时应力值  alloy 合金  alloy steel 合金钢  alteration 改进  alternate floor 隔层  alumina 氧化铝  aluminum 铝  aluminum alloy 铝合金  aluminum bronze 铝青铜  aluminum cladding 铝制包层  alumite 防蚀铝  alundum 氧化铝  ambient 环境的  ambient noise 环境噪音  ambient temperature 环境温度  ammeter 安培计  ammonia 氨  amperage 电流强度  ampere 安培  amplification 放大  amplification stage 放大等级  amplifier 放大器  amplifying tube 放大管  amplitude 幅度  analog adder 模拟加法器  analog computer 模拟计算机  analog speed card 模拟曲线板  analog-digital converter 模拟-数字转换器  analogue(analog) 模拟  analysis 分析  analysis mode 分析模拟  anchor bolt 地脚螺栓  anchorage "锚具,锚定"  angle bar 角钢  angle guide 角铁导轨  angle iron 角铁  angle iron frame 角铁框架  angle of contact 接触角  angle of deflection 导向角  angle of inclination 倾斜角  angle of lead 导程角  angle of traction 曳引机包角  angle of wrap 包角  angle steel 角钢  angular contact ball bearing 向心推力球轴承  angular contact bearing 角面接触滚动轴承  angular gear 斜齿轮  angular retardationg 角减速度  angular velocity 角速度  anneal 退火  annealing 退火  annual inspection 年检  annual report 年度报告  annunciator "报音器,声音合成器"  anode 阳极  anodize 氧极氧化  ANSI(America Nationa Standard Instirute) 美国国家标准协会  anti-clockwise 逆时钟方向  anti-corrosive paint 防腐蚀漆  anti-creep 防蠕动  anti-friction bearing 抗摩擦轴承  anti-nuisance 防干扰  anti-nuisance device 防捣乱装置  anti-phase braking 反向制动  anti-phase current 反相电流  anti-rebound of compensation rope device 补偿绳防跳装置  anti-residual 防剩磁  anti-resonance 抗谐振  anti-reversion device 防反转装置  anti-rust 防锈  anti-stall 防空转  anti-vibralion pad 防震垫  APM(automatic people mover) 自动人员运输机  apparen power 视在功率  apparent output 视在输出  applicant 申请人 application 申请  application guide 应用指南  aprons 裙板  arbour "轴,杆"  arc chamber 电弧隔离室  arc protection 防电弧  arc quenching 熄焊弧  arc shield 电弧屏蔽  arc suppressor 灭焊器  architect 设计单位  architecture 建筑学  architrave 门框  area 面积  arm "臂,支路"  armature 电驱  armature coil 电驱线圈  armature current 电驱电流  armature lamination 电驱铁芯片  armature shaft 电驱轴  armature spider 星形轮  armature winding 电驱绕组  armoured 蛇皮管的  armoured cable 蛇皮管电缆  armoured conduit 导线管  arrangement 布置  arrival bell 到站铃  arrival buzer 到站蜂鸣器  arrival floor 到达楼层  arrival gong 到站钟  arrival rate 到站率  article of consumption 消耗品  artificial intelligence 人工智能  artistic 工艺  artistic face 工艺表面  asbestos packing 石棉盘根  ascending 上升  ASIC(application specific integrated circuit) 专用集成电路  assemble 装配  assembler language 汇编语言  assembly of hinge 铰链组装  assign 分配  astragal 装饰镶条  atmospheric influence 大气影响  attachment 附件  attendant control 有司机控制  attendant control compartment 有司机控制盒  attendant operation 有司机操作  audible signal 音响信号  audio tape recording 磁带录音  authority "当局,核准部门"  authority of lift acceptance 电梯验收部门  authorized "授权的,核准的"  authorized user 核准使用者  auto-adaptation 自适用  AutoCAD 自动计算机辅助设计  autographic recoder 自动记录仪  automatic 自动的  automatic allocator 自动分派器  automatic by-pass 自动直驶  automatic center opening sliding door 自动中分式滑动门  automatic closer 自动关闭门  automatic dispatch 自动调度  automatic door 自动门  automatic homing 自动回基层  automatic landing 自动停站  automatic landing system by spare battery 靠备用蓄电池的自动停站设备  automatic leveling 自动平层  automatic lubricator 自动润滑装置  automatic parking garage 自动停车库  automatic parking system 自动停车系统  automatic relevelling 自动平层校正  automatic rescue device 应急救助装置  automatic return 自动返回  automatic telescopic center opening sliding door 自动中分式折叠滑动门  automatic telescopic sliding door 自动折叠式滑动门  automobile lift 汽车电梯  autowalk 自动人行道  auxiliary apparatus 辅助装置  auxiliary brake 辅助制动器  auxiliary cicuit 辅助电路  auxiliary contact 辅助触点  auxiliary drive 辅助驱动  auxiliary lock 辅助锁  auxiliary materials 辅助量  auxiliary value 辅助材料  auxiliary winding 辅助绕组  available area 有效面积  average 平均  average car load 平均轿厢负载  average dispatching interval 平均调度间隔时间  average interval 平均调度间隔时间  average passenger waiting time 平均乘客侯梯时间  average response time 平均应答时间  average waiting quest 平均乘客量  average waiting time 平均乘客侯梯时间  axial flow fan 轴流式风扇  axis 轴线  axle 轴 babbit 巴氏合金  babbit lined bearing 巴氏合金衬里轴承  babbit melter 巴氏合金熔化器  babbit metal 巴氏合金  babbit rope socket 灌注式巴氏合金绳头  back current 反向电流  back e.m.f 反电动势  back lash 轮齿隙  back plunger type 后部柱塞式(液压梯)  back side "后侧,后边"  back type governor 轴流式限速器  back wall 后壁  baked enamel 烤漆  balace weight 平衡器  balance 平衡  balance chain 平衡链  balance coefficient 平衡系数  balanced traffic 平衡交通  ball bearing 滚珠轴承  ball cup 球形碗  ball pin 球形硝  ball stop valve 球形断流器  ball type bearing 滚珠轴承  ballast 镇流器  balustrade deching 外侧盖板  balustrade exterior panelling 外装饰板  balustrade lighting 扶手照明  balustrade panel 扶手板  balustrade skirting 扶手群板  balustrades 扶手装置  bandsaw 带锯  bank "银行,群组,排"  bar "条,棒"  bar code 条形码  bar lock 杆式锁  bare wire 裸线  barricade "防护墙,隔墙"  barrier "隔板,栅栏"  base "基座,基础"  base plate 基板  basement 地下室  basement service 底下室服务  basement type 底吊式  basic logic element 基础逻辑元件  basic logic function 基础逻辑功能  batch production 批量生产  battery 电池  battery- backed 电池支持的  battery box 蓄电池箱  battery charger 电池充电器  baud rate 波特率  BCD(binary coded decimal) 二进制编码的十进制  beam 梁  beam pad 井道内电缆保护垫片  beam pulley 抗绳轮  bearing 轴承  bearing bracket 轴承支架  bearing cap 轴承盖  bearing load 轴承负荷  bearing plate 承重板  bearing play 轴承间隙  bearing sleeve 轴承衬套  bearing stand 轴承座  bed lift 病床电梯  bed plate 底座  bell 铃  belt 胶带  belt drive 胶带传动  belt grinder 胶带磨床  belt pulley 胶带轮  belt type moving walk 带式自动人行道  bending 弯曲  bending stress 弯曲应力  benzine 轻汽油  bevel gear 伞(斜)齿轮  beveled washer 斜垫圈  BGM (background music) 背景音乐  BGM speaker 背景音乐扬声器  bias "偏置,偏移"  bid "投标,报价"  bid table 报价单  bidder 投标  bidding cycle 投标有效期限  bidding procedure 投标(报价)程序  bil of delivery 发货单  bil of lading 海运提单  bill of expenses 费用帐单  bill of materials 材料单  billing 开发票  binary 二进制  binder 装订册  bi-parting 对开式(上下开启)  bi-parting door 垂直中分门  bipartite light transistor 双分式光电管  bistable magnetic swich 双稳态磁开关  bistable switch 双稳态磁开关 bitumen 沥青  blade "叶片,刀片,锯片"  blade connector 刀形连接器  bleed-off circuit 泄放电路  blind hoistway 盲(无门)井道  block chart 方框图  block diagram 方框图线路  block of flats 住宅楼区  blocking of control circuit 控制电路闭锁  blower 鼓风机  blower coil 吹弧线圈  blower motor 风机电动机  blue print 蓝图  boading floor 登梯楼层  boading time 登梯时间  boarding 登梯  boarding landing 登梯层站  boarding passenger 登梯乘客boarding rate 登梯率  boarding stop 登梯停站  boarding zone 登梯区域  bobbing 绕线管  boldface type 粗字体  bolt 螺杆  booster 升压机  border condition 边界条件  bore hole "钻孔,镗孔"  boring 镗  boring lathe 镗床  boring machine 镗床  boring miller 镗铣床  bottom 底部  bottom car clearance 轿底安全高度间隙  bottom car overtravel 底部轿厢越程  bottom car runby 底部轿厢越程  bottom clearances for car 轿底间隙  bottom counterweight clearance 轿底对重间隙  bottom counterweight overtravel 轿底对重越程  bottom counterweight runby 轿底对重越程  bottom door retainer 门下角  bottom floor 底部楼层  bottom runby 底部越程  bottom slow down switch 底部减速开关  bottom stop 底部停战  bottom terminal floor 底部楼层  bottom terminal landing 底部端站  bottom terminal stop 底端停站  box "盒,箱"  box counterweight 箱式对重  Braille 盲文字符  brake 制动器  brake arm 制动器臂  brake contact 制动器触点  brake coutact 制动器联轴器  brake dish 制动盘  brake drum 制动轮  brake energy 制动力  brake level 制动器杠杆  brake lever 制动器手柄  brake lining 制动器衬套  brake linkage 制动器连杆  brake operater switch 制动操纵开关  brake pin 制动器悄  brake press "折弯机,压弯机"  brake pulley 制动轮  brake release lever 制动器松闸手柄  brake release magnet 制动器送闸磁铁  brake release time 制动器松闸时间 brake shoe 制动靴  brake spacing 制动器间距  brake spring 制动弹簧  brake tension 制动器张紧力  brake torque 制动器力矩  brake wrench 制动器板手  braking 制动  braking distance 制动距离  braking force 制动力  branch circuit 分支电路  brass founder 铸铜  break "切断,破断"  break-down 故障  breaking load 破断负荷  breaking strength 破断强度  breaking test 破坏实验  breather 通气管  brick 砖  brick-layer 砖砌工  bridge circuit 桥式电路  bridge connector 桥接器  bridge jumper 桥接片  bridge rectifier 桥式整流器  bright controlling 光度控制  broach 拉力  broaching machine 拉床  brochure 手册  broken chain contact 断链触点  broken circuit 断路  broken drive chain contact 主驱动链保护装置  broken drive-chain safety device 驱动链条保护装置  broken rope contact 驱动链条列断安全装置  broken step chain contact 断绳触点  broken step chain device 断绳开关  broken step chain safety device 梯级链断列触点  broken step safety device 梯级破列安全装置  broken tape sweitch 短带开关  bronze 铜  brunching "成组,成群"  brush finished stainless steel 哑光不锈钢  brush holder "刷握,滑环"  brush yoke 刷架  budget 预算  buffer 缓冲器  buffer base 缓冲器底座  buffer plate 缓冲器板  buffer plunger 缓冲器柱塞  buffer return spring 缓冲器复位弹簧  buffer stand 缓冲器台  buffer striking plate 缓冲器撞板  buffer stroke 缓冲器冲程  buffer support 缓冲器支承  buffer switch 缓冲器开关  buider's work drawing 土建图纸  buiding facility 大楼设施  buiding supervision center 大楼监管中心  builder 建筑单位  building 建筑  building area 建筑面积  building contractor 建筑承包商  building manager 大楼管理者  building monitoring and security system 大楼监管和安全系统  building population 大楼居住人口  built=in 内装  built-in escalator 组合式自动扶梯  bumper 弹簧式缓冲器  bumper rail 防撞板  bumpy ride 颠簸振动的运行  buried 埋入的  burn in (程序)灌入  burr "毛刺,毛边"  burr free 去毛刺  bus 总线  bus bar 汇流条  bush 衬套  bushed bearing 加衬轴套  bushing "衬套,轴套,套筒"  butt joint "平接,对焊"  button 按钮  button switch 按钮开关  buyer 买方  buzzer 蜂鸣器  buzzer switch 蜂鸣器开关  bypass 直驶  by-pass button 直驶按钮  by-pass valve 溢流阀  bypassed floor 直驶不停楼层  bypassed stop 直驶不停层站 C$F 到岸价  cab "轿厢,座舱"  cab interior 轿厢内部  cabin "轿厢,座舱"  cabinet "柜,厢"  cable 电缆  cable box 电缆箱  cable car 缆车  cable cleat 电缆夹具  cable conductor 电缆导线  cable entry 电缆引入  cable hanger 电缆吊架  cable hole 电缆孔  cable joint 电缆接头  cable termination 电缆末端  cable trunk 电缆接头  CAD 计算机辅助设计  cage 轿厢  cage door 轿厢门  calculation 计算机辅助设计  calibrate 校准  call "呼梯,呼叫"  call acceptance 呼梯接收  call accepted 接受呼梯  call accepted indicator 接受呼梯指示灯  call accepted signal 接受呼梯信号  call allocation 呼梯分派  call assignment 呼梯指令分配  call band 呼梯信号带  call button 呼梯按钮  call cancel 呼梯取消  call canceling 呼梯取消  call coincidence 呼梯重合  call conmting system 呼梯计数系统  call contrl 呼梯指令控制  call emitter 呼梯指令发送器  call input 呼梯输入  call input capacity 呼梯输入内容  call input device 呼梯输入装置  call load 呼梯输入  call memory 呼梯记忆  call registered 登陆的呼梯  call registered signal 登陆的呼梯信号  call registration indicator 呼梯登陆信号  call sequence 呼梯顺序  call tegistration 呼梯登陆  call-back 召修  call-back message 召修信息  callinfg board 召唤盒  calling floor 呼体楼层  calling landing 呼梯  call-out response time 维修召唤应答时间  call-out service 急修服务  CAM 计算机辅助制造  cam 凸轮  cam for positive operation 强制操纵凸轮  cam lever 偏心柄  cam shaft 偏心轴  cam tape control 偏心带控制  cam-gear 凸轮传动装置  cam-operated switch 凸轮(碰铁)操纵开关  cancel "撤消,取消"  cancelingof call signal 呼梯信号消除  cancellation "撤消,取消"  canopy "顶盖,大蓬"  canvas 帆布  canvas hose 帆布软管  cap "帽,盖子"  cap nut 螺母  capacitance "电容,电容量"  capacitor 电容  capacitor motor 电容器电机  capacity "载重,容量,定员"  capacity plate 载量标牌  capstan 绞盘  captive roller safety gear 滚柱式安全钳  car 轿厢  car annunciator 轿厢报警器  car approaching gong 轿厢到站预报钟  car apron 轿厢入口群板  car assignment "轿厢调度,轿厢分配"  car automatic switch landing 轿厢开关自动停站  car axis 轿厢中心线  car back wall 轿厢后壁  car botom clearance 轿厢安全高度  car