阀门标准-MSS SP6-2001(天选打工人).pdf

STD-MSS SP-b-ENGL 2001=5770b40 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings Standard Practice Developed and Approved by the Manufacturers Standardization Society of the Valve and Fittings Industry,Inc.I27 Park Street,NE Vienna,Virginia 22180(703)281-661 3 COPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesCOPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesSTD-MSS SP-b-ENGL 2001 E 5770b40 OSUL427 524 E MSS STANDARD PRACTICE SP-6 This MSS Standard Practice was developed under the consensus of MSS Technical Committees 102,1 1 O,201,and the MSS Coordinating Committee.The content of this Standard Practice is the result of the efforts of competent and concerned volunteers to provide an effective,clear,and non-exclusive specification that will benefit the industry as a whole.This MSS Standard Practice is intended as a basis for common practice by the manufacturer,the user,and the general public.The existence of an MSS Standard Practice does not in itselfpreclude the manufacture,sale or use of products not conforming to the Standard Practice Mandatory conformance is established only by reference in a code,specification,sales contract,or public law,as applicable.I Substantive changes in this 2001 edition are“flagged”by parallel bars as shown on the margins of this paragraph.The specific detail of the change may be determined by comparing the material flagged with that in the previous edition.U.S.customary units in this SP are the standard;the metric(SI)units are only for reference.Unless otherwise specifically noted in this MSS SP,any standard referred to herein is identified by the date of issue that was applicable to the referenced standard(s)at the date of issue ofthis MSS SP.(See Annex A).Any part o f this standard may be quoted.Credit lines should read Extractedfrom MSSSP-6,2001 with permission o f the publisher,the Manufacturers Standardization Socieg.Reproduction prohibited under copyright convention unless written permission is granted by the Manufacturers Standardization Socieg o f the Valve and Fittings Indus-try,Inc.Originally Approved December 1929 Copyright O,1985 by Manufacturers Standardization Society of the Valve and Fittings Industry,Inc.Printed in U.S.A.1 COPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesCOPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesSTD-MSS SP-b-ENGL 2001 I 5770bl10 050/1i30?Yb W MSS STANDARD PRACTICE SP-6 STANDARD FINISHES FOR CONTACT FACES OF PIPE FLANGES AND CONNECTING END FLANGES OF VALVES AND FITTINGS 1.SCOPE 1.1 This standard pertains to the finish of gasket contact faces of pipe flanges and end flanges of valves and fittings.1.2 It is intended for application to products for which ASME B 16 Standards do not contain com-plete facing finish requirements or for which there are no such Standards.2.DEFINITIONS 2.1 Roughness Average.The term Ra(rough-ness average)is expressed in micro-inches(pin)micro-meters(pm).2.2 Flange Facing Finish.The surface finish on the flange contact face,see Figure 1,that comes I in contact with a gasket upon flange assembly.3.REQUIREMENTS 3.1 Flange facing finish shall be judged by visual comparison with Ra standards(see ASME B46.1)and not by instniments having stylus tracers and elec-tronic amplification.The finishes required are given in Table 1.Other finishes may be furnished by agree-ment between purchaser and manufacturer.3.2 Dimensions shown(in Table 1)shall not be cause for rejection by depth gage measurement or precision instrument measurements.4.LIMITATIONS 4.1 timum for all gasket types of materials.Surface finishes listed are not necessarily op-4.2 On flat faces,serrations need not extend be-yond corresponding raised face diameter.I FLAT I l l 6 RAISED 114 RAISED RING FACE FACE FACE JOINT SMALL MALE IL LARGE MALE&SMALL TONGUE&LARGE TONGUE&FEMALE FEMALE GROOVE GROOVE FIGURE 1 Types of Contact Faces for Flanges 1 COPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesCOPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesSTDOMSS SP-b-ENGL 2001 5770b4ll O50143L 192 E MSS STANDARD PRACTICE SP-6 STANDARD FINISHES FOR CONTACT FACES OF PIPE FLANGES AND TABLE 1 CONNECTING-END FLANGES OF VALVES AND FITTINGS Type of Contact Faces Flat or 1/16”(1.6 mm)Raised Face and 1/4”(6.4 mm)Raised and Large Male&Female Small Male&Female,Large&Small Tongue&3roove Ring Joint-Side Walls of Groove Steel Serrated(a):spiral or concentric,45 to 55 per inch(18 to 21 per cm)recommended.The resultant surface finish shall have a 125 to 250 pin(3.2 to 6.3 pm)Ra.Serrated(as above)(4 or Non-serrated:125 pin.(3.2 pm)Ra max.Non-serrated:63 pin.(1.6 clm)Ra max.Ductile Iron Non-serrated(b):250 pin(6.3 pm)Ra max.,or Serrated(a):sprial or concentric,11 to 50 per in.(5 to 19 per cm).Depth approx.0.003 to 0.020 in.(0.075 to 0.51 mm)Non-serrated:63 pin.(1.6 um)Ra max.Gray Iron Non-serrated(b):250 pin(6.3 pm)Ra max.,or Serrated(a):spiral,1 1 to 50 per in.(5 to 19 per cm)or concentric,8 or more per in.(4 or more per cm).Depth approx.0.003 to 0.020 in.(0.075 Bronze Non-serrated(b):125 pin(3.2 pm)Ra max.,or Serrated(a):sprial or concentric,30 to 80 per in.(12 to 31 cm).Depth approx.0.003 to 0.020 in.(0.075 to 0.5 1 mm)NOTES:(ahless otherwise specified,the manufacturer may supply either spiral or concentric grooves for serrations.The spiral machining operation is commonly accomplished with the cutting tool having 0.06 in.(1.6 mm)or larger tip radius.(b)Unless otherwise specified,the manufacturer may supply either the serrated(commonlv accomplished with the cutting tool having 0.06 in.Il.6 mm)or larger tip radius)or smooth finish.2 COPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesCOPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling Services-STD*MSS SP-b-ENGL 2001 m 577b10 flC0143?1111 m MSS STANDARD PRGCTICE SP-6 ANNEX A REFERENCED STANDARDS AND APPLICABLE DATES This Annex is an integral part of this Standard Practice and is placed after the main text for convenience.Standard Name or Designation ASME,ANSUASME,ANSI,ASME/ANSI I B46.1-1995 Surface Texture(Surface Roughness,Waviness,and Lay)The following organizations publish the above standard:ANSI American National Standards Institute,Inc.11 West 42nd Street,New York,NY 10036 I ASME The American Society of Mechanical Engineers Three Park Avenue,New York,NY 10016-5990 3 COPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesCOPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesSTD.MSS SP-b-ENGL 2001=577b40.0501Y33 6 List of MSS Standard Practices(Price List Available Upon Request)Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings Spot Facing for Bronze,Iron and Steel Flanges Standard Marking System For Valves,Fittings,Flanges and Unions Class 150 Corrosion Resistant Gate,Globe,Angle and Check Valves with Flanged and Butt Weld Ends(R 01)Wrought Stainless Steel Butt-welding Fiings Steel Pipeline Flanges Bypass and Drain Connections Class 150LW Corrosion Resistant Cast Flanges and Flanged Fittings Quality Standard for Steel Castings and Forgings for Valves.Flanges and Fittings and Other Piping Componets-Magnetic Particle Number SP-6-2001 SP-9-2001 SP-25-1998 SP-42-1999 SP43-1991 SP44-1996 SP-45-1998 SP-51-2000 SP-53-1999 SP-54-1999 SP-55-1996 SP-58-1993 SP-60-1999 SP-61-1999 SP-65-I999 SP-67-1995 SP-68-1997 SP-69-1996 SP-70-1998 SP-71-1997 SP-72-1999 SP-73-1991 SP-75-1998 SP-77-I995 SP-78-1998 SP-79-1999a SP-80-1997 SP-81-2000 SP-82-1992 SP-83-1995 SP-85-1994 SP-86-1997 SP-87-1991 SP-88-1993 SP-89-1998 SP-90-2000 SP-91-1992 SP-92-1999 SP-93-1999 SP-94-1999 SP-95-2000 SP-96-1996 SP-97-1995 SP-98-1996 SP-99-1994 SP-100-1997 SP-101-1989 SP-I 02-1 989 SP-103-1995 SP-104-1995 SP-I o51 996 SP-I 06-1 990 SP-I 07-1 991 SP-108-1996 SP-109-1997 SP-l10-1996 SP-111-1996 SP-112-1999 SP-113-2M)l SP-I 14-1 995 SP-115-1999 SP-116-1996 SP-117-1996 SP-118-1996 SP-119-1996 SP-120-1997 SP-121-1997 SP-122-1997 SP-123-1998 SP-124-2001 SP-I 25-2000 SP-126-2000 Examination Method Qualitv Standard for Steel Castings for Valves,Flanges,and Fittings and Other Piping Components-Radiographic Examination Method Qualit;Standard for Steel Castings for Valves,Flanks and Ftngg and Other Piping Components-Visual Method for Evaluation Of Sutface Irregularities Pipe Hangers and Supports-Materials,Design and Manufacture Connecting Flange Joint Between Tapping Sleeves and Tapping Valves Pressure Testing of Steel Valves High Pressure Chemical Industry Flanges and Threaded Stubs for Use with Lens Gaskets Butte Valves High Pressure Butterfly Valves with Offset Design Pipe Hangers and Supports-Selection and Application Cast Iron Gate Valves,Flanged and Threaded Ends Gray Iron Swing Check Valves,Flanged and Threaded Ends Ball Valves with Flanged or Butt Welding Ends for General Service(R 96)Brazing Joints for Wrought and Cast Copper Alloy Solder Joint Pressure Fittings Specification for High Test Wrought Butt Welding Fittings(R 00)Guidelines for Pipe Support Contractual Relationships Cast Iron Plug Valves,Flanged and Threaded Ends Swket-Welding Reducer Inserts Bronze Gate,Globe,Angle and Check Valves Stainless Steel,Bonnetless,Flanged,Knife Gate Valves Valve Pressure Testing Methods Class 3000 Steel Pipe Unions,Socket-Welding and Threaded Cast Iron Globe&Angle Valves,Flanged and Threaded Ends Guidelines for Metric Data in Standards for Valves,Flanges,Fittings and Actuators(R 96)Factory-Made Butt-welding Fittings for Class 1 Nuclear Piping Applications Diaphragm Type Valves Pipe Hangars and Supports-Fabrication and Installation Practices Guidelines on Terminology for Pipe Hangers and Supports(R 96)Guidelines for Manual Operations of Valves MSS Valve User Guide Quality Standard for Steel Castings and Forgings for Valves,Flanges,and Fittings and Other Piping Components-Liquid Penetrant Examination Method Quality Std for Ferritic and Martensitlc Steel Castings for Valves,Flanges,and Fittings and Other Piping Components-Ultrasonic Examination Method Swage(d)Nipples and Bull Plugs Guidelines on Terminology for Valves and Fittings Integrally Reinforced Forged Branch Outlet Fittings-Socket Welding,Threaded and Buttwelding Ends Protective Coatings for the Interior of Valves,Hydrants,and Fittings Instrument Valves Qualification Requirements for Elastomer Diaphragms for Nuclear Diaphragm Type Valves Part-Turn Valve Actuator Attachment-Flange and Driving Component Dimensions and Performance Characteristics Multi-Turn Valve Actuator Attachment-Flange and Driving Component Dimensions and Performance Characteristics(R 00)Wrought Copper and Copper Alloy Insert Fittings for Polybutylene Systems Wrought Copper Solder Joint Pressure Fittings Instrument Valves for Code Applications(R 96)Cast Copper Alloy Flanges and Flanged Fittings,Class 125,150 and 300(R 00)Transition Union Fittings for Joining Metal and Plastic Products Resillent-Seated Cast Iron-Eccentric Plug Valves Welded Fabricated Copper Solder Joint Pressure Fittings Ball Valves Threaded,Socket-Welding,Solder Joint,Grooved and Flared Ends Gray-Iron and Ductile-Iron Tapping Sleeves Quality Standard for Evaluation of Cast Surface Finishes-Visual and Tactile Method.This SP must be sold with a IO-surface,three dimensional Cast Surfa-Comparator.which is a necessary pari o the Standard.Additional comparators may be sold separately at$25.00 each.Same quantity discounts apply on total order.Connecting Joint between Tapping Machines and Tapping Valves Corrosion Resistant Pipe Fittings Threaded and Socket Welding,Class 150 and 1000 Excess Flow Valves for Natural Gas Service Service Line Valves and Fittings for Drinking Water Systems Bellows Seals for Globe and Gate Valves Compact Steel Globe&Check Valves-Flanged,Flangeless,Threaded&Welding Ends(Chemical&Petroleum Refinery Service)Belled End Socket Welding Fittings,Stainless Steel and Copper Nickel Flexible Graphite Packing System for Rising Stem Steel Valves(Design Requirements)Qualification Testing Methods for Stem Packing for Rising Stem Steel Valves Plastic Industrial Ball Valves Non-Ferrous Threaded and Solder-Joint Unions for Use with Copper Water Tube Fabricated Tapping Sleeves Gray Iron and Ductile Iron In-Line,Spring-Loaded,Center-Guided Check Valves Steel In-Line Spring-Assisted Center Guided Check Valves(R YEAR)Indicates year standard reaffimied without substantive changes A large number of former MSS Practices have been approved by the ANSI or ANSI Standards,published by others.In order to maintain a single source of authoritative information,the MSS withdraws its Standard Practice in such cases.Manufacturers Standardization Society of the Valve and Fittings Industry,Inc.127 Parkstreet,N.E.,Vienna,VA22180-4620.(703)281-6613 Fax#(703)281-6671 COPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling ServicesCOPYRIGHT Manufacturers Standardization Society of the Valve and FittingsLicensed by Information Handling Services