55度管螺纹尺寸(共5页).doc

《55度管螺纹尺寸(共5页).doc》由会员分享，可在线阅读，更多相关《55度管螺纹尺寸(共5页).doc（5页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上55圆柱管螺纹的型式和尺寸螺纹代号基本尺寸大径mmd=D螺距mmp每英寸牙数tpi中径mmd2=D2小径外螺纹d3牙型高度H1底孔尺寸mmG 1/8 1/89.7280.907289.1478.5660.5818.7G 1/4 1/413.1571.3371912.30111.4450.85611.6G 3/8 3/816.6621.3371915.80614.950.85615G 1/2 1/220.9551.8141419.79318.6311.16219G 5/8 5/822.9111.8141421.74920.5871.16220.75G 3/4 3/426

2、.4411.8141425.27924.1171.16224.5G 7/8 7/830.2011.8141429.03927.8771.16228G 1 133.2492.3091131.7730.2911.47930.5G 1 1/8 1 1/837.8972.3091136.41834.9391.47935G 1 1/4 1 1/441.912.3091140.43138.9521.47939.5G 1 3/8 1 3/8 44.3232.3091142.84441.3651.47941.5G 1 1/2 1 1/247.8032.3091146.32444.8451.47945G 1 3

3、/4 1 3/453.7462.3091152.26750.7881.47951G 2 259.6142.3091158.13556.6561.47957G 2 1/4 2 1/465.712.3091164.23162.7521.47963G 2 1/2 2 1/275.1842.3091173.70572.2261.47972.5G 2 3/4 2 3/481.5342.3091180.05578.5761.47979G 3 387.8842.3091186.40584.9261.47985.G 3 1/4 3 1/493.982.3091192.50191.0221.47991G 3 1

4、/2 3 1/2100.332.3091198.35197.3721.47997.75G 3 3/4 3 3/4106.682.30911105.201103.7221.479104G 4 4113.032.30911111.55110.0721.479110.5G 4 1/2 4 1/2125.732.30911124.251122.7721.479123G 55138.432.30911136.951135.4721.479136G 5 1/2 5 1/2151.132.30911149.651148.1721.479148.5G 6 6163.832.30911162.351160.87

5、21.479161.555圆锥管螺纹的型式和尺寸螺纹代号基本尺寸大径mmd=D螺距mmp每英寸牙数tpi中径mmd2=D2小径外螺纹d3牙型高度H1圆弧尺寸 r底孔尺寸 mmR 1/161/167.7230.907287.1426.5610.5810.1256.4R 1/81/89.7280.907289.1478.5660.5810.1258.4R 1/41/413.1571.3371912.30111.4450.8560.18411.2R 3/83/816.6621.3371915.80614.9500.8560.18414.75R 1/21/220.9551.8141419.79318.

6、6311.1620.24918.25R 3/43/426.4411.8141425.27924.1171.1620.24923.75R 1133.2492.3091131.7730.2911.4790.31730R 1 1/41 1/441.9102.3091140.43138.9521.4790.31738.5R 1 1/21 1/247.8032.3091146.32444.8451.4790.31744.5R 2259.6142.3091158.13556.6561.4790.31756R 2 1/22 1/275.1842.3091173.70572.2261.4790.31771R

7、3387.8842.3091186.40584.9261.4790.31785.5R 44113.0302.30911111.551110.0721.4790.317110.5R 55138.4302.30911136.951135.4721.4790.317136R 66163.8302.30911162.351160.8721.4790.317161.51、密封管螺纹（R）密封管螺纹不加填料或密封质就能防止渗漏。用密封管螺纹内螺纹有圆锥、圆柱两种形式，外螺纹只有圆锥一种形式。配合方式：英制密封管螺纹有两种配合方式：圆柱内螺纹与圆锥外螺纹组成“柱/锥”配合；圆锥内螺纹与圆锥外螺纹组成“锥/锥

8、”配合。欧洲国家主要采用“柱/锥”配合螺纹；而欧洲以外国家则主要采用“锥/锥”配合螺纹。标记：英制密封圆柱内螺纹的特征代号为：RP； 英制密封圆锥内螺纹的特征代号为：RC； 英制密封圆锥外螺纹的特征代号为： R1（与英制密封圆柱内螺纹配合使用）； R2（与英制密封圆锥内螺纹配合使用）；对密封管螺纹，利用RP/R1，RC/R2分别表示“柱/锥”和“锥/锥”螺纹副。2、非密封管螺纹非密封管螺纹主要用于压力较低的水管、煤气管道，连接时就加填料或密封质（麻丝、铅丹、聚四氟乙烯胶带等），以防止渗漏标记。非密封管螺纹不论内外螺纹都只有圆柱螺纹一种形式。英制非密封圆柱螺纹的特征代号为：G（例G1/4）当表示英制非密封管螺纹的螺纹副时，仅标注外螺纹的标记代号。加工内孔螺纹的是管螺纹丝锥，加工外螺纹的有板牙。注意：两种管螺纹部分规格的公差不同（密封管螺纹精度更高）。 非螺纹密封的圆柱内螺纹可以和用螺纹密封的圆锥外螺纹相连接，但非螺纹密封的圆柱外螺纹却不可以和用螺纹密封的圆锥内螺纹形成用螺纹密封的连接。专心-专注-专业