汽车常用术语英汉词典(共290页).doc

《汽车常用术语英汉词典(共290页).doc》由会员分享，可在线阅读，更多相关《汽车常用术语英汉词典(共290页).doc（290页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上汽车词典 轮椅升降机 Wheel chair lift 图例 legend 工位 station 吊运装置 overhead hoist 更衣室 restroom 1号厂房工艺布置方案图 proposal of the Plant I layout 合笼 mate 底盘平移台 chassis shuttle 车辆转移台 bus transfer 前围角板 front wall angle cover 后围侧板 rear wall side cover 保险杠 bumper 三类底盘 three type chassis 左侧围应力蒙皮 R/S stretching s

2、kin (road side) 中涂 floating coat 拼装台 collector 切割轮口 wheel -arch cutting 内饰 trim 线束 harness 返工 re-doing 轮罩护板 wheel house 发车前准备 pre-delivery 举升 hoist 小批量产品 be pilot 2 套 two kits 配电站 power transformer substation 裙板 skirt 发动机托架 engine holding frame 诊断报警系统 diagnosis and alarming system 互换性 interchangeabi

3、lity 缩微图纸 microfiche files 总装 final assembly 磷化 phosphating 仪表板 dash board 切齐 trimming 结构完整性 structure integrity 自动愈合的防腐材料 self-healing corrosion preventative material 长途客车 inter-city bus 改装厂 refitting factory 遮阳板 sun visor 随车工具 tool box 钢化玻璃 toughened grass 异形钢管 special steel pipe 全天候空调系统 full rang

4、e A/C 强制通风 ram-air ventilation 停机时间 downtime 无公害柴油 clean diesel 宽敞悬臂式座椅 roomy cantilevered seat 防滑地板 no-skid floor 织物纹里铝合金 textured aluminum extrution 爬坡能力 grade ability 排水阀 drain valve 除湿器 moisture ejector 怠速时 at idle 琴式驱动桥 banjo type drive axle 通风口 duct 恒温控制 thermostatic control 平衡水箱 surge tank 变光

5、开关 simmer switch 消音器 muffler 防破坏 vandal resistant 聚碳化透镜 poly-carbonate lens 镀锌板 galvanized plate 搭接 lap 亮丽的外表 smart appearance 隐藏式固定 concealed fastening 水洼 ponding 发动机中置式客车 bus with under floor engine 组合式客车车身 modular bus body 薄壳式结构 shell construction 衬垫 pad 空气导流板 air deflector 搁梁 shelf beam 腰梁 waist

6、 rail 梭梁 stabilizing beam 腰带式安全带 diagonal safety belt 压条 trim strip 嵌条 insertion strip 翼板 fender 斜撑 bracing piece 转向盘回正性试验 test of steering wheel returnability 转向盘转角脉冲试验 steering wheel impulse input test 转向盘转角阶跃输入试验 steering wheel step input or transient state yaw response test 极限侧向加速度试验 limiting la

7、teral acceleration test 汽车平顺性随机输入行驶试验 automobile ride random input running test 汽车平顺性单脉冲输入行驶试验 automobile ride single pulse input running test 汽车悬挂系统固有频率与阻尼比的测定试验 measurement of natural frequency and damping ratio of suspension 功率突然变化影响试验 test of effect of sudden power change 收油门后控制试验 test of contro

8、l at breakway 横风稳定性试验 test of crosswind stability 反冲试验 kick-back test 轮胎爆破响应时间试验 test of burst response of tyre 绕过障碍物试验 obstacle avoidance test 移线试验 lane change test J型转弯试验 test of J turn 频率响应时间试验 frequency response test 瞬态响应时间试验 transient response test 阶路响应时间试验 step response test 脉冲响应试验 pulse respo

9、nse test 静态操舵力试验 static steering effort test 悬架举升试验 jack-up test of suspension 耐翻倾试验 test of overturning immunity 轮辋错动试验 rim slip test 风洞试验 wind tunnel test 制动稳定性试验 test of braking stability 最小转弯直径试验 minimum turning diameter test 操舵力试验 steering effort test 汽车发动机 类型 engine 内燃机 internal combustion eng

10、ine 内燃机power unit 动力机装置gasoline engine 汽油机gasoline-injection engine 汽油喷射式汽油机spark ignition engine 火花点火式发动机compression ignition engine 压燃式发动机reciprocating internal combustion engine 往复式内燃机化油器式发动机 carburetor engine 化油器式发动机diesel engine 柴油机rotary engine 转子发动机rotary trochoidal engine 旋轮线转子发动机two-stroke

11、engine 二冲程发动机four-stroke engine 四冲程发动机direct injection engine 直接喷射式柴油机indirect injection engine 间接喷射式柴油机supercharged engine 增压式发动机air-cooled engine 风冷式发动机oil-cooled engine 油冷式发动机water-cooled engine 水冷式发动机naturally aspirated engine 自然进气式发动机gas engine 煤气机liquified petroleum gas engine 液化石油气发动机diesel g

12、as engine 柴油煤气机multifuel engine 多种燃料发动机石油发动机 hydrocarbon engine 石油发动机duel fuel engine 双燃料发动机hot bulb engine 热球式发动机multiple cylinder engine 多气缸发动机opposed piston engine 对置活塞发动机opposed-cylinder engine 对置气缸式发动机cross head engine 十字头型发动机in-line engine 直列式发动机radial engine 星型发动机trunk-piston engine 筒状活塞发动机st

13、irling engine 斯特林发动机knight engine 套阀式发动机port-scavenged engine 气孔扫气式发动机slant engine 倾斜式发动机front-engine 前置式发动机rear-engine 后置式发动机central engine 中置式发动机left-hand engine 左侧发动机right-hand engine 右侧发动机oversquare engine 短冲程发动机undersquare engine 长冲程发动机square engine 等径程发动机overhead camshaft engine 顶置凸轮轴发动机dual o

14、verhead camshaft engine 双顶置凸轮轴发动机V-engine V形发动机valve in-head engine 顶置气门发动机side valve engine 侧置气门发动机valveless engine 无气门发动机multi-valve engine 多气门发动机horizontal engine 卧式发动机inclined engine 斜置式发动机vertical engine 立式发动机w-engineW形发动机 I-engine I形发动机L-engine L形发动机机 F-engine F形发动performance 性能two-stroke cycl

15、e 二冲程循环four-stroke cycle 四冲程循环diesel cycle 狄塞尔循环otto cycle 奥托循环mixed cycle 混合循环定容循环 constant volume cycle 工作循环 working cycle等压循环 constant pressure cycle 理想循环 ideal cycle 热力循环 thermodynamic cycle 冲程 stroke 活塞行程 piston stroke长行程 long stroke 上行程 up stroke 下行程 down stroke 进气行程 intake stroke 充气行程 chargin

16、g stroke压缩行程 compression stroke 爆炸行程 explosion stroke 膨胀行程 expansion stroke 动力行程 power stroke 排气行程 exhaust stroke 膨胀换气行程 expansion-exchange stroke 换气压缩行程 exchange-compression stroke 止点 dead center 上止点 top dead center(upper dead center) 下止点 lower dead center(bottom dead center) 上止点前 budc(before upper

17、 dead center) 上止点后atdc(after top dead cetner) 下止点前 bbdc(before bottom dead center) 下止点后 abdc(after bottom dead center) 缸径 cylinder bore 缸径与行程 bore and stroke 空气室 energy chamber 气缸余隙容积 cylinder clearance volume 燃烧室容积 combustion chamber volume 气缸最大容积 maximum cylinder volume 压缩室 compression chamber 排气量

18、 displacement 发动机排量 engine displacement 活塞排量 piston swept volume 气缸容量 cylinder capacity 单室容量 single-chamber capacity 容积法 volumetry 压缩比 compression ratio 临界压缩比 critical compression ratio 膨胀比 expansion ratio 面容比 surface to volume ratio 行程缸径比 stroke-bore ratio混合比 mixture ratio压缩压力 compression pressure

19、制动平均有效压力 brake mean effective pressure(bmep) 空燃比 air fuel ratio 燃空比 fuel air ratio 燃料当量比 fuel equivalence ratio 扭矩 torque 单缸功率 power per cylinder 升功率 power per liter 升扭矩 torque per liter 升质量 mass per liter 减额功率 derating power 输出马力 shaft horsepower 马力小时，马力时 horsepower-hour 总马力 gross horse power 总功率 g

20、ross power 净功率 net power 燃油消耗量 fuel consumption 比燃料消耗率 specific fuel consumption 空气消耗率 air consumption 机油消耗量 oil consumption 有效马力 net horse power 额定马力 rated horse power 马力重量系数 horsepower-weight factor 制动功率 brake horse power 制动热效率 brake thermal efficiency 总效率 overall efficiency 排烟极限功率 smoke limiting

21、horsepower 功率曲线 power curve 机械损失 mechanical loss 机械效率 mechanical efficiency 有效热效率 effective thermal efficiency 充气系数 volumetric efficiency 过量空气系数 coefficient of excess air 适应性系数 adaptive coefficient 扭矩适应性系数 coefficient of torque adaptibility 转速适应性系数 speed adaptive coefficient 强化系数 coefficient of inte

22、nsification 校正系数 correction factor 换算系数 conversion factor 活塞平均速度 mean piston speed 发动机转速 engine speed (rotational frequency) 怠速转速 idling speed 经济转速 economic speed 起动转速 starting speed 最低稳定工作转速 lowest continuous speed with load 最大扭矩转速 speed at maximum torque 最高空转转速 maximum no load governed speed 调速 sp

23、eed governing 超速 overspeed 怠速 idling 转速波动率 speed fluctuation rate 工况 working condition(operating mode) 额定工况 declared working condition 变工况 variable working condition 稳定工况 steady working condition 空载 no-load 全负荷 full load 超负荷 overload 部分负荷 part load 充量（进气） charge 旋转方向 direction of rotation 顺时针 clockw

24、ise 逆时针 counter-clockwise 左转 left-hand rotation 右转 right-hand rotation 外径 major diameter 中径 pitch diameter 内径 minor diameter 径向间隙 radial clearance 发动机性能 engine performance 加载性能 loading performance 起动性能 starting performance 加速性能 acceleration performance 动力性能 power performance 排放性能 emission performanc

25、e 空转特性 no load characteristics 负荷特性 part throttle characteristics 调速特性 governor control characteristics 万有特性 mapping characteristics 稳定调速率 steady state speed governing rate 气缸体和气缸盖 cylinder block and head 气缸体 cylinder block 整体铸造 cast inblock (cast enblock) 发动机罩 engine bonnet 气缸体加强筋 engine block stif

26、fening rib 气缸 cylinder （转子机）缸体 stator 缸径 cylinder bore 气缸体机架 cylinder block frame 气缸盖 cylinder head 配气机构箱 valve mechanism casing 气缸体隔片 cylinder spacer 气缸盖密封环 cylinder head ring gasket 气缸盖垫片 cylinder head gasket 气缸套 cylinder liner(cylinder sleeve) 干式缸套 dry cylinder liner 湿式缸套 wet cylinder liner 气缸水套

27、water jacket 膨胀塞 expansion plug 防冻塞 freeze plug 气缸壁 cylinder wall 环脊 ring ridge 排气口 exhaust port 中间隔板 intermediate bottum 导板 guideway 创成半径（转子机） generating radius 缸体宽度（转子机） operating width 机柱 column 燃烧室 combustion chamber 主燃烧室 main combustion chamber 副燃烧室 subsidiary combustion chamber 预燃室 prechamber

28、涡流燃烧室 swirl combustion chamber 分开式燃烧室 divided combustion chamber 涡流式燃烧室 turbulence combustion chamber 半球形燃烧室 hemispherical combustion chamber 浴盆形燃烧室 bathtub section combustion chamber L形燃烧室 L-combustion chamber 楔形燃烧室 wedge-section combustion chamber 开式燃烧室 open combustion chamber 封闭喷射室 closed spray c

29、hamber 活塞顶内燃烧室 piston chamber 爆发室 explosion chamber 燃烧室容积比 volume ratio of combustion cahmber 燃烧室口径比 surface-volume ratio of combustion chamber 通道面积比 area ratio of combustion chamber passage 曲轴箱通气口 crankcase breather 凸轮轴轴承座 camshaft bearing bush seat 定时齿轮室罩 camshaft drive(gear)cover 曲轴箱检查孔盖 crankcas

30、e door 曲轴箱防爆门 crankcase explosion proof door 主轴承盖 main bearing cap 气缸盖罩 valve mechanism cover 飞轮壳 flywheel cover 扫气储器 scavenging air receiver 活塞 piston 裙部开槽活塞 split skirt piston U形槽活塞 U-slot piston 滚花修复活塞 knurled piston 圆顶活塞 dome head piston 平顶活塞 flat head piston 凸顶活塞 crown head piston(convex head p

31、iston) 凹顶活塞 concave head piston 阶梯顶活塞 step-head piston 筒形活塞 trunk piston 椭圆形活塞 oval piston 抗热变形活塞 autothermic piston 不变间隙活塞 constant clearance piston 镶因瓦钢片活塞 invar strut piston 直接冷却式活塞 direct-cooled piston 间接冷却式活塞 indirect cooled piston 滑裙活塞 slipper piston 活塞速度 piston speed 活塞顶部 piston head 活塞裙部 pis

32、ton skirt 整体活塞裙 solid skirt 活塞裙扩大衬簧 piston skirt expander 滑履式活塞裙 slipper skirt 隔热槽 heat dam 活塞标记 piston mark 活塞销 piston pin 活塞销孔 piston pin boss 活塞销衬套 piston pin bushing 全浮式活塞销 full-floating piston pin 半浮式活塞销 semifloating piston pin 固定螺钉式活塞销 set screw piston pin 活塞环 piston ring 组合式活塞环 compound pisto

33、n ring 同心活塞环 concentric piston ring 偏心活塞环 eccentric piston ring 自由环 free ring 闭合环 closed ring 梯形环 keystone ring 半梯形环 half keystone ring 矩形环 rectangular ring 油环 oil control ring 开槽油环 slotted oil control ring 螺旋弹簧加载双坡口油环 coil spring loaded slotted oil control ring 涨环 expander 双坡口油环 double bevelled oil

34、 control ring 内上坡口 internal bevel top 内下坡口 internal bevel bottom 边缘坡口油环 bevelled-ege oil control ring 刮油环 scrapper ring 钩形环 napier ring 镀铬活塞环 chrome plated piston ring 活塞衬环 piston ring expander 活塞环槽 piston ring groove 活塞环区 ring zone 活塞环岸 piston ring land 活塞环内表面 back of ring 曲柄连杆机构 connecting rod 中心曲

35、柄连杆机构 central-located connecting rod 偏心曲柄连杆机构 offset connecting rod 铰接曲柄边杆机构 hinged connecting rod 连杆 connecting rod 连杆小头 connecting rod small end 连杆大头 connnecting rod big end 连杆杆身 connecting rod shank 副连杆 slave connecting rod 叉形连杆 fork-and-blade connecting rod 主连杆 main connecting rod 方形连杆 boxed rod

36、 绞链式连杆 hinged type connecting rod 活节式连杆 articulated connecting rod 连杆盖 connecting rod cap 连杆轴承 connecting rod bearing 曲轴 crankshaft 整体式曲轴 one-piece crankshaft 组合式曲轴 assembled crankshaft 右侧曲轴 right-hand crankshaft 左侧曲轴 left-hand crankshaft 改变行程的曲轴 stroked crankshaft 曲轴前端 crankshaft front end 曲轴主轴颈 cr

37、ankshaft main journal 轴颈重叠度 shaft journal overlap 圆角 fillet 主轴承 main bearing 曲轴止推轴承 crankshaft thrust bearing 薄臂轴瓦 thin wall bearing shell 曲轴油道 crankshaft oil passage 曲柄 crank 曲柄臂 crank arm 曲柄销 crank pin 轴套 bush 曲柄转角 crank angle 曲柄半径 crank radius 抛油圈 oil slander 角度轮 degree wheel 动平衡机 dynamic balance

38、r 平衡重 balancer weight 扭振减振器 torshional vibration damper 扭振平衡器 torsion balancer 谐振平衡器 harmonic balancer 振动平衡器 vibration balancer 曲轴链轮 crankshaft sprocket 转子轴颈 rotor journal 偏心轴 eccentric shaft 曲轴箱 crankcase 闭式曲轴箱通风装置 closed-crankcase ventilating system 飞轮 flywheel 飞轮齿圈 flywheel ring gear 飞轮芯棒 cantile

39、ver 飞轮芯轴 flywheel spindle 飞轮的惯量矩 flywheel moment of inertia 飞轮标记 flywheel mark 当量系统 equivalent system 当量轴长 equivalent shaft length 一级往复惯性力 reciprocating inertia force,1st order 二级往复贯性力 reciprocating inertia force, 2nd order 离心惯性力 centrifugal inertia force 配气机构 valve gear 凸轮轴 camshaft 凸轮 cam 整体式凸轮轴 o

40、ne-piece camshaft 组合式凸轮轴 assembled camshaft 凸轮轴驱动机构 camshaft drive 赛车用凸轮轴 race camshaft 凸轮轴轴颈 camshaft bearing journal 凸轮轴轴承 camshaft bearing 凸轮轴偏心轮 camshaft eccentric 凸轮轴链轮 camshaft sprocket 凸轮轴正时齿轮 camshaft timing gear 凸轮轴齿轮 camshaft gear wheel 进口凸轮 inlet cam 排气凸轮 exhaust cam 快升凸轮 quick lift cam 快

41、升缓降凸轮 quick lift gradual clsing cam 凸轮轮廓 cam contour 凸轮包角 cam angle 凸轮升程 cam-lobe lift 凸轮尖 cam nose 凸轮从动件 cam follower 齿轮传动机构 gear drive 正时齿轮 timing gear 链传动机构 chain drive 链轮 sprocket wheel 链轮盘 chain sprocket 正时链条 timing chain 带齿皮带 toothed timing belt 链条张紧轮 chain tension gear 半速齿轮 half speed gear 正时

42、齿轮刻印记号 timing gear punch mark 气门 valve 进气过程 intake process 换气过程 gas exchange process 扫气过程 scavenging process 给气比 delivery ratio 分层充气 stratified charge 充量系数 volumetric efficiency 涡流比 swirl rate 进气涡流 intake swirl 螺旋进气道进气 helical duct intake 导流屏式气门进气 masked valve intake 切向进气道进气 tangential duct intake 进

43、气紊流 intake trubulence 进气提前角 intake advance angle 进气持续角 intake duration angle 进气迟后角 intake lag angle 进面值 time-area value 气门升程 valve lift 气门正时 valve timing 扫气口面积 scavenging port area 菌形气门 mashroom valve, poppet valve 钠冷却气门 sodium filled valve(natrium cooled valve) 双气门 dual valve 进气门 intake valve (suct

44、ion valve,inlet valve) 排气门 exhaust valve 顶置气门 overhead valve 侧置气门 side valve 倾斜气门 inclined overhead valve 直立气门 vertical overhead valve 套筒式滑阀 sleeve valve 气门机构 valve gear 直接式气门驱动机构 direct valve gear 间接式气门驱动机构 indirect valve gear 气门杆 valve stem 加大气门杆 oversize valve stem 气门头 valve head 气门工作面 valve face

45、 气门边限 valve margin 气门弹簧座 valve-spring retainer 气门锁片 valve key 气门间隙调节螺钉 valve lash adjusting screw 气门旋转器 valve rotator 气门室 valve cage 气门油封 valve oil seal 气门口 valve port 气门座 valve seat 气门座镶圈（嵌镶式气门座圈） valve seat insert(valve seat ring) 气门座锥角 valve seat angle 气门座宽度 valve seat width 气门挺杆 valve tappet(val

46、ve lifter) 液力挺杆 hydraulic tappet(lifter) 无间隙挺杆 zero-rush tappet (non-clearance tappet) 筒形挺杆 barrel type tappet 油压挺杆 ooil tappet 滚轮挺杆 roller tappet(lifter) 挺杆转位 tappet rotation 排气门挺杆 exhaust valve lifter 气门导管 valve guide 气门杆导管 stem guide 气门重叠度 stem overlap 气门开启持续时间 valve duration 气门正时标记 valve timing sign 气门弹簧 valve spring 气门内弹簧 inner valve spring 气门外弹簧 o