组件过程及最终检验标准(共4页).docx

《组件过程及最终检验标准(共4页).docx》由会员分享，可在线阅读，更多相关《组件过程及最终检验标准(共4页).docx（4页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上一、过程检验标准1.芯片检验标准 芯片级别检 验 标 准A级转换效率14%(单晶）或13.5%（多晶）；正面无挂浆；无裂纹；细棚线断线0.5mm不超过3条且不连续分布；缺角和崩口0.5mm2 不超过3个；层压后无明显色差；无逆电流；2.玻璃检验标准玻璃级别检 验 标 准A级透光率95%，气泡线度2mm 不超过3个，极浅划伤 L10mm 不超过3条；崩边向中间延伸1mm不超过3个；平整度5%3.铝合金检验标准铝合金级别检 验 标 准A级铝合金标号6063T5；表面氧化均匀，氧化膜层厚度10um；表面无划伤、无鼓包；两端高、宽、厚等线度尺寸相差0.3mm4.涂锡带检验标准

2、尺寸公差0.01mm，涂锡层均匀，易于焊接，抗拉强度好，不易断裂。5.接线盒检验标准密封、防水，能与硅橡胶牢固粘合，耐老化，绝缘，具有旁路二极管，二极管具有足够的反向耐压和较低正向漏电流，二极管具有高低温的耐温性，整个线路具有较低的电阻，盒体具有足够的散热空间，插头具有好的耐疲劳性二、最终检验标准技术级别功率范围外形尺寸正 面 外 观边框外观背面外观A级3%公差1.0mm两端尺寸相差0.5mm芯片无挂浆，边缘裂纹5mm不超过1条，细栅线断线0.5mm不超过3条且不连续分布，缺角和崩口0.5mm2不超过3个，表面无明显色差；玻璃极浅划伤L10mm不超过3条；组件气泡3mm2不超过3个；芯片间距离

3、不小于1mm，芯片与边框间距离不小于8mm表面氧化均匀，表面无划伤、无鼓包；两端线度尺寸相差0.3mmTPT无皱痕，表面干净，拱起点高度0.2mm;硅胶均匀；接线盒粘接牢固，表面干净三、相应规格电气性能参数125*125 MONO 180WpSpecifications Data Max. Power180WpCell TypeMono-Crystalline Silicon Sorlar CellNo.Of Cells 72 seriesMax.System Voltage1000VDCPower Tolerance3%Surface Maximum Load Capacity60m/s(2

4、00kg/sq.m)Weight15.5kgDimemsions158080835mmElectrical Characeteristic Open Circuil Voltage(V) 44.4Short Circuil Currenl(A)5.40Max.Power Voltage(V)35.6Max.power Current(A)5.05Temperature Coefficienls of Isc(%)+0.017%Temperature Coefficienls of Voc(%)-0.34%Temperature Coefficienls of Pm(%)-0.48%Operat

5、ing Temperralure-40 to + 85Conditions:(STC):Irradiance:1000W/m2, spectral distribution AM1.5, Cell temperature:25Features and BenefitsHigh efficicncy solar cells Nominal 24V DC for standard outputCells are Iaminated with EVA, TPT and tempered glass ensuring long life and the most stringent safety re

6、quirements for high-voltage operation.Anodized aluminum frame with convenience mounting slotsWithstand hing wind pressure and snow loadOutstanding low-light performancePreeminent aesthetic appearanceEasy installationOutput power tolerance of 3%25 year limited warranty on power output, 2 year limited

7、 warranty on materials and workmanship156*156 100WpSpecifications Data Max. Power100WpCell TypeMono-Crystalline Silicon Sorlar CellNo.Of Cells 36 seriesMax.System Voltage1000VDCPower Tolerance3%Surface Maximum Load Capacity60m/s(200kg/sq.m)Weight10.0kgDimemsions147667035mmElectrical Characeteristic

8、Open Circuil Voltage(V) 21.4Short Circuil Currenl(A)5.40Max.Power Voltage(V)17.6Max.power Current(A)6.40Temperature Coefficienls of Isc(%)+0.017%Temperature Coefficienls of Voc(%)-0.34%Temperature Coefficienls of Pm(%)-0.48%Operating Temperralure-40 to + 85Conditions:(STC):Irradiance:1000W/m2, spect

9、ral distribution AM1.5, Cell temperature:25Features and BenefitsHigh efficicncy solar cells Nominal 12V DC for standard outputCells are Iaminated with EVA, TPT and tempered glass ensuring long life and the most stringent safety requirements for high-voltage operation.Anodized aluminum frame with convenience mounting slotsWithstand hing wind pressure and snow loadOutstanding low-light performancePreeminent aesthetic appearanceEasy installationOutput power tolerance of 3%25 year limited warranty on power output, 2 year limited warranty on materials and workmanship专心-专注-专业