英语专用术语(共7页).doc

《英语专用术语(共7页).doc》由会员分享，可在线阅读，更多相关《英语专用术语(共7页).doc（7页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上英语专用术语(电镀品质)四、量具电子千分尺 Digimatic outside micrometer 高度尺 height gauge普通千分尺 micrometer 基准尺 snap micrometer长度比较仪 length comparator 坑卡 blade micrometer内径千分尺 Inside micrometer 带表卡尺 dial caliper光学扫描仪 TESA 塞规 pin gauge投影仪 projector 牙规 thread gauge 内牙规 thread plug gauge圆度仪 Roundness tester 外牙规 t

2、hread ring gauge轮廓仪 contracer 放大镜 magnifier 光洁度仪surface roughness tester同轴度仪 concentricity gauge 内径杆规 bore gauge 环规Ring gauge五、刀具名称 刀把扳手 holder spanner 超硬铣刀 super-rigidity cutter 中锋刀把 center hilt 槽刀刀把 groovy hilt 丝攻 The silk offend 光刀粒 Light knife grain 边车刀磨 The side sword whet 前行粗刀 ex-rough knife 中

3、分刀粒 centre-knife grain 前行槽刀粒 ex- slot knife grain 前行面刀 ex-side knife 后行面刀 backside knife 平口槽刀 the even slot knife 中行刀粒 Medium knife grain 槽刀粒 groove knife grain 光切刀 light cutting 粗切刀 rough cutting 槽光刀 light groove sword 槽粗刀 rough groove sword 活动扳手 adjustable spanner 角铣刀 angle cutter 去角刀具 chamfering

4、tool 凹面铣刀 concave cutter凸行铣刀 convex cutter 刃用锉刀 edge file 锉刀 file导轮 idler pulley 凹刀 concave cutter 钻头 aiguille刀角 nose angle 砂轮 grinding wheel 滚花轮 knurled wheel T行刀板 T cutter plank 脱模钳 wiper 扳手 spanner钳子 pinchers 手摇钻 hand brace 冲头 punch刀刃角 tool point angle 磨光器 polisher 砂纸 sand paper铗钳 pliers 劈刀 rivin

5、g knife 劈尖；楔 wedge喷咀 nozzle 喷砂 sand blasting 胶片,刀,勾刀plastic cutter治具 jig 工具箱 kit 千斤顶 jack分度头 index head 凸缘接头 flange joint 剖面线 hatching六角螺帽 hexagon 六角头螺栓 hexagon headed bolt 螺丝起子 screw driver划线 scribiing 直角尺 square 直角度 square trowel负角刀粒 Negative Cape 前行面刀粒 front knife grain 后行面刀粒 back knife grain前孔刀

6、Ex- bore sword 麻花钻 twist drill 铣刀 milling cutter 后孔钩刀 the back bore bushhook 前孔光刀 Ex- bore light knife 内牙刀 inner tooth knife平口钻 The even drill 外牙刀 outer tooth knife 凹刀 concave sword金钻 golden drill PCB钻 PCB drill 钻头 aiguille外牙刀 outer tooth knife 光孔刀粒 Light bore knife grain 前行光刀粒 ex-light knife grain后

7、行光刀粒back-light knife grain 平口槽刀粒the even groove knife grain 平口槽粗刀 the even rough groove knife成型钻 molding drill 中心钻 The center drill 三刃铣刀 Three blades milling cutter四刃铣刀 four blades milling cutter台阶钻 step drill 粗锣刀片 rough razor blade of gong精锣刀片 extract razor blade of gong 成型倒角刀Model to pour the Cape

8、 sword 平口铲刀 the even shovel knife端面槽刀 end face groove 手提钻孔机 protable driller 切断刀 sever牙刀 Tooth sword 刮刀 scraper 扳手 spanner 方栓槽拉刀spline broach 方行镘刀 square sleeker 车刀 tool for lathe刀刃角 tool point angle 刀架 tool post 螺旋扳手 wrench两角规 compass 柱塞头 plug 去毛边 trimming金工锯 metal saw 研磨 lapping 修正笔 revise带式打磨机bel

9、t sander 铁 iron 心轴 mandril十字接头 cross joint 钻台 drill stand 夹具 clamp超硬圆车刀super-rigidity turning tool hilt 锣刀片柄 Razor blade handle of gong铁锤 hammer 反手槽粗刀 Thick knife of anti- hand slot 平口槽光刀 the even slot light knife反手槽光刀light knife of anti-hand groove 钻咀 drill 平口孔刀 the even bore knife 槽刀 groove 后孔倒角刀

10、back bore pours Cape knife六、 金属切屑 Metal filings 金属加工 Metal working, metal processing 铣螺纹 thread milling铣槽刀具 grooving tool 铣削 milling 铣床 milling lathe铣床夹具 fraise jig 毛边 burrs 毛胚 blank绝缘体 insulator, nonconductor 绝缘 insulation; isolation 绝缘材料 insulating materials, insulant工程 engineering, project 工程计划 e

11、ngineering planning 工程进度表 construction schedule工程进展报告 report on the process of work 工程图 schedule drawing, project drawing, engineering drawing生产线 production line 生产指数 productivity index 生产误差 production error生产流程图 process chart 生产调节 production adjustment 生产能力 productivity, production capacity 生产量 pro

12、ductive output 生锈 rustiness, corrosion生锈表面 rusty surface 脱皮（漆膜） lacquer lifting 脱灰 bate pits, deliming脱色 decolourization, discolourization 脱轨 derailment, disorbit 脱位 dislocation脱层 delamination 脱环 decycling 脱线 off-line脱盐 desalte 脱铅 deleading 脱离 abscission, disengagement电镀 electroplated, electrolytic(

13、al) deposition galvanization 电镀工 galvanizer电镀加工 electroplated finish 电镀层 electroplated coating 附着力 Physics adhesive force; adhesion 实物 material object, object刀痕 Tool mark 面积 Mathematics the measure of area; square measure; superficial measure; superficial content(s)杂质 impurities 麻 (surface) not smoo

14、th 垫片 Mechanics a spacer导热 Physics heat conduction缺角、沙眼、破损,浮起,划痕 trachoma, breakage, drifting, lacking horn, scratch marks领料单 a material requisite formbarrel 滚筒(加工) bending 波纹加工 broaching 拉刀切削 centering 定中心 cutting 切削 cylindrical lathe cutting 外圆车削 electric discharge machine 放电加工 electrolytic grindi

15、ng 电解研磨 embossing 压花加工 facing 面车削 filing 锉刀修润 hand finishing 手工修润 hemming 卷边加工 hobbing 滚齿加工 joggling 摇动加工 lapping 抛光/研磨修润 laser beam machining 雷射加工 lathe cutting 车床车削 planning 刨削加工 polishing 抛亮光 reaming 铰孔修润 rough machining 粗切削 rounding 圆形加工 sawing 锯削 scaling 清除钢碇缺陷 shaping 成形加工 skiving 表面研磨 slottin

16、g 切缝切削 taper turning 锥度车削 thread cutting 螺纹切削 ultrasonic machining 超音波加工 up cut milling 逆铣加工 autocollimator 自动准直机 bench comparator 比长仪 block gauge 块规 bore check 精密小测定器 calibration 校准 caliper gauge 卡规 check gauge 校对规 clearance gauge 间隙规 clinoretee 测斜仪 comparator 比测仪 cylinder square 圆筒直尺 depth gauge 测

17、深规 dial indicator 针盘指示表 dial snap gauge 卡规 digital micrometer 数位式测微计 feeler gauge 测隙规 gauge plate 量规定位板 height gauge 测高规 inside calipers 内卡钳 inside micrometer 内分卡 interferometer 干涉仪 leveling block 平台 limit gauge 限规 micrometer 测微计 mil 千分之一寸 monometer 压力计 morse taper gauge 莫氏锥度量规 nonius 游标卡尺 optical f

18、lat 光学平晶 optical parallel 光学平行 passimeter 内径仪 position scale 位置刻度 profile projector 轮廓光学投影仪 protractor 分角器 radius 半径 ring gauge 环规 sine bar 正弦量规 snap gauge 卡模 square master 直角尺 stylus 触针 telescopic gauge 伸缩性量规 working gauge 工作量规 ES Engineering Standarization 工程标准 IWS International Workman Standard 工

19、艺标准 ISO International Standard Organization 国际标准化组织 GS General Specification 一般规格 PMC Production & Material Control 生产和物料控制 PPC Production Plan Control 生产计划控制 MC Material Control 物料控制 ME Manafacture Engineering 制造工程部 PE Project Engineering 产品工程部 A/C Accountant Dept 会计部 P/A Personal & Administration

20、人事行政部 DC Document Center 资料中心 QE Quality Engineering 品质工程(部) QA Quality Assurance 品质保证(处) QC Quality Control 品质管制(课) PD Product Department 生产部 LAB Labratry 实验室 IE Industrial Engineering 工业工程 R&D Research & Design 设计开发部 P Painting 烤漆(厂) A Asssembly 组装(厂) S Stamping 冲压(厂) abrasive 砂轮 Al2O3 氧化铝 balance

21、 平衡 bond 结合 borazon 氧化硼立方晶 buffing wheel 抛光布轮 diamond 钻石 dresser 砂轮整修机work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常

22、用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |plein?|刨床 miller铣床 grinder磨床 driller?床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory direct

23、or厂长 department director部长 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 fina

24、l inspection终检 to connect material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 dressing 修整 endless grinding belt 循环式研磨带 finishing allowance 加工余量 grain 磨粒 grinding disc 研磨盘 jamp up 孔眼堵塞 mesh 网筛目 parameter 参数 resinoid grinding wheel 半树脂型砂轮 slitting 切缝量 vitrified 陶瓷的 wheel 旋转Assem

25、bly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管

26、supervisor 课长 ME制造工程师 MT制造生技cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造

27、作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机 punchin

28、g machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |plein?|刨床 miller铣床 grinder磨床 driller?床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manage

29、r | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect material接料to r

30、everse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to load material上料 to unload material卸料 to return material/stock to退料 scraped |skr?pid|报废 scrape .v.刮;削 deficient purchase来料不良 manufacture procedure制程 deficient manufacturing procedure制程不良 oxidation | ksidei?n|氧化 scratch刮伤 dents压痕 defective

31、 upsiding down抽芽不良 defective to staking铆合不良 embedded lump镶块 feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车 compound die合模 die locker锁模器 pressure plate=plate pinch压板 bo

32、lt螺栓 name of a department部门名称 administration/general affairs dept总务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板 hydraulic handjack油压板车 forklift叉车 p

33、allet栈板 glove(s)手套 glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴 iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper扫把 mop拖把 vaccum cleaner吸尘器 rag 抹布 garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条 jack升

34、降机 production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机 packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格 dimension/

35、size is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 sh

36、rinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots水渍 polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交货期 cost成本 engin

37、eering工程 die repair模修 enterprise plan = enterprise expansion projects企划 QC品管 die worker模工 production, to produce生产equipment设备 to start a press开机 stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养 qualified products, up-to-grade products良品 defective products,

38、 not up-to-grade products不良品 waste废料 board广告牌 feeder送料机 sliding rack滑料架 defective product box不良品箱die change 换模 to fix a die装模 to take apart a die拆模 to repair a die修模 packing material包材 basket蝴蝶竺 plastic basket胶筐 isolating plate baffle plate; barricade隔板 carton box纸箱 to pull and stretch拉深 to put mate

39、rial in place, to cut material, to input落料 to impose lines压线 to compress, compressing压缩 character die字模to feed, feeding送料 transportation运输 (be)qualfied, up to grade合格 not up to grade, not qualified不合格 material change, stock change材料变更 feature change 特性变更 evaluation评估 prepare for, make preparations f

40、or 准备 parameters参数 rotating speed, revolution转速 manufacture management制造管理 abnormal handling异常处理 production unit生产单位 lots of production生产批量 steel plate钢板 roll material卷料 manufacture procedure制程 operation procedure作业流程 to revise, modify修订 to switch over to, switch-to throw-over switching over切换 engin

41、eering, project difficulty 工程瓶颈 stage die工程模 automation自动化 to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模 shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for stamping 冲压常词汇 stamping, press冲压 punch press, dieing out press冲床 uncoiler & straingh

42、tener整平机 feeder送料机 rack, shelf, stack料架 cylinder油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤 deformation变形 filings铁削 to draw holes抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取 approval examine and