单片机C语言程序设计实训100例.doc

《单片机C语言程序设计实训100例.doc》由会员分享，可在线阅读，更多相关《单片机C语言程序设计实训100例.doc（57页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、【精品文档】如有侵权，请联系网站删除，仅供学习与交流单片机C语言程序设计实训100例.精品文档.单片机C语言程序设计实训100例基于8051+Proteus仿真案例第 01 篇 基础程序设计01闪烁的LED/* 名称：闪烁的LED说明：LED按设定的时间间隔闪烁#include#define uchar unsigned char#define uint unsigned intsbit LED=P10;/延时void DelayMS(uint x)uchar i;while(x-)for(i=0;i120;i+);/主程序void main()while(1)LED=LED;DelayMS(

2、150);02 从左到右的流水灯/* 名称：从左到右的流水灯说明：接在P0口的8个LED从左到右循环依次点亮，产生走马灯效果#include#include#define uchar unsigned char#define uint unsigned int/延时void DelayMS(uint x)uchar i;while(x-)for(i=0;i120;i+);/主程序void main()P0=0xfe;while(1)P0=_crol_(P0,1); /P0的值向左循环移动DelayMS(150);03 8只LED左右来回点亮/* 名称：8只LED左右来回点亮说明：程序利用循环移

3、位函数_crol_和_cror_形成来回滚动的效果#include#include#define uchar unsigned char#define uint unsigned int/延时void DelayMS(uint x)uchar i;while(x-)for(i=0;i120;i+);/主程序void main()uchar i;P2=0x01;while(1)for(i=0;i7;i+)P2=_crol_(P2,1); /P2的值向左循环移动DelayMS(150);for(i=0;i7;i+)P2=_cror_(P2,1); /P2的值向右循环移动DelayMS(150);0

4、4 花样流水灯/* 名称：花样流水灯说明：16只LED分两组按预设的多种花样变换显示#include#define uchar unsigned char#define uint unsigned intuchar code Pattern_P0= 0xfc,0xf9,0xf3,0xe7,0xcf,0x9f,0x3f,0x7f,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff, 0xe7,0xdb,0xbd,0x7e,0xbd,0xdb,0xe7,0xff,0xe7,0xc3,0x81,0x00,0x81,0xc3,0xe7,0xff, 0xaa,0x55,0x1

5、8,0xff,0xf0,0x0f,0x00,0xff,0xf8,0xf1,0xe3,0xc7,0x8f,0x1f,0x3f,0x7f, 0x7f,0x3f,0x1f,0x8f,0xc7,0xe3,0xf1,0xf8,0xff,0x00,0x00,0xff,0xff,0x0f,0xf0,0xff, 0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff, 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0x7f,0xbf,0xdf,0xef,0xf7,0xfb,

6、0xfd,0xfe, 0xfe,0xfc,0xf8,0xf0,0xe0,0xc0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xc0,0xe0,0xf0,0xf8,0xfc,0xfe, 0x00,0xff,0x00,0xff,0x00,0xff,0x00,0xffuchar code Pattern_P2= 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xfe,0xfc,0xf9,0xf3,0xe7,0xcf,

7、0x9f,0x3f,0xff, 0xe7,0xdb,0xbd,0x7e,0xbd,0xdb,0xe7,0xff,0xe7,0xc3,0x81,0x00,0x81,0xc3,0xe7,0xff, 0xaa,0x55,0x18,0xff,0xf0,0x0f,0x00,0xff,0xf8,0xf1,0xe3,0xc7,0x8f,0x1f,0x3f,0x7f, 0x7f,0x3f,0x1f,0x8f,0xc7,0xe3,0xf1,0xf8,0xff,0x00,0x00,0xff,0xff,0x0f,0xf0,0xff, 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0

8、xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f, 0x7f,0xbf,0xdf,0xef,0xf7,0xfb,0xfd,0xfe,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff, 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xfe,0xfc,0xf8,0xf0,0xe0,0xc0,0x80,0x00, 0x00,0x80,0xc0,0xe0,0xf0,0xf8,0xfc,0xfe,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff, 0x00,0xff,0x00,0x

9、ff,0x00,0xff,0x00,0xff/延时void DelayMS(uint x)uchar i;while(x-)for(i=0;i120;i+);/主程序void main()uchar i;while(1)/从数组中读取数据送至P0和P2口显示for(i=0;i136;i+)P0=Pattern_P0i;P2=Pattern_P2i;DelayMS(100);05 LED模拟交通灯/*名称：LED模拟交通灯说明：东西向绿灯亮若干秒，黄灯闪烁5次后红灯亮， 红灯亮后，南北向由红灯变为绿灯，若干秒后南北向黄灯闪烁5此后变红灯，东西向变绿灯，如此重复。#include#define u

10、char unsigned char#define uint unsigned intsbit RED_A=P00; /东西向灯sbit YELLOW_A=P01;sbit GREEN_A=P02;sbit RED_B=P03; /南北向灯sbit YELLOW_B=P04;sbit GREEN_B=P05;uchar Flash_Count=0,Operation_Type=1; /闪烁次数，操作类型变量/延时void DelayMS(uint x)uchar i;while(x-) for(i=0;i120;i+);/交通灯切换void Traffic_Light()switch(Oper

11、ation_Type)case 1:/东西向绿灯与南北向红灯亮RED_A=1;YELLOW_A=1;GREEN_A=0;RED_B=0;YELLOW_B=1;GREEN_B=1;DelayMS(2000);Operation_Type=2;break;case 2:/东西向黄灯闪烁，绿灯关闭DelayMS(300);YELLOW_A=YELLOW_A;GREEN_A=1;if(+Flash_Count!=10) return; /闪烁5次Flash_Count=0;Operation_Type=3;break;case 3:/东西向红灯，南北向绿灯亮RED_A=0;YELLOW_A=1;GRE

12、EN_A=1;RED_B=1;YELLOW_B=1;GREEN_B=0;DelayMS(2000);Operation_Type=4;break;case 4:/南北向黄灯闪烁5次DelayMS(300);YELLOW_B=YELLOW_B;GREEN_B=1;if(+Flash_Count!=10) return;Flash_Count=0;Operation_Type=1;/主程序void main()while(1) Traffic_Light();06 单只数码管循环显示09/*名称：单只数码管循环显示09说明：主程序中的循环语句反复将09的段码送至P0口，使数字09循环显示#incl

13、ude#include#define uchar unsigned char#define uint unsigned intuchar code DSY_CODE=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0xff;/延时void DelayMS(uint x)uchar t;while(x-) for(t=0;t120;t+);/主程序void main()uchar i=0;P0=0x00;while(1) /* for(;i11;i+) P0=DSY_CODEi; DelayMS(300); /注:另一方案 */P0=DSY_C

14、ODEi;i=(i+1)%10;DelayMS(300);07 8只数码管滚动显示单个数字/*名称：8只数码管滚动显示单个数字说明：数码管从左到右依次滚动显示07，程序通过每次仅循环选通一只数码管#include#include#define uchar unsigned char#define uint unsigned intuchar code DSY_CODE=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90;/延时void DelayMS(uint x)uchar t;while(x-) for(t=0;t120;t+);/主程序vo

15、id main()uchar i,wei=0x80;while(1)for(i=0;i8;i+)P2=0xff; /关闭显示wei=_crol_(wei,1);P0=DSY_CODEi; /发送数字段码P2=wei; /发送位码DelayMS(300);08 8只数码管动态显示多个不同字符电路如上图/*名称：8只数码管动态显示多个不同字符说明：数码管动态扫描显示07。#include#include#define uchar unsigned char#define uint unsigned intuchar code DSY_CODE=0xc0,0xf9,0xa4,0xb0,0x99,0x

16、92,0x82,0xf8,0x80,0x90;/延时void DelayMS(uint x)uchar t;while(x-) for(t=0;t120;t+);/主程序void main()uchar i,wei=0x80;while(1)for(i=0;i8;i+)P2=0xff;P0=DSY_CODEi; /发送段码wei=_crol_(wei,1);P2=wei; /发送位码DelayMS(2);09 8只数码管闪烁显示数字串电路如上图/*名称：8只数码管闪烁显示数字串说明：数码管闪烁显示由07构成的一串数字 本例用动态刷新法显示一串数字，在停止刷新时所有数字显示消失。#include

17、#define uchar unsigned char#define uint unsigned int/段码表uchar code DSY_CODE=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90;/位码表uchar code DSY_IDX=0x01,0x02,0x04,0x08,0x10,0x20,0x40,0x80;/延时void DelayMS(uint x)uchar t;while(x-) for(t=0;t120;t+);/主程序void main()uchar i,j;while(1)for(i=0;i30;i+)for(j

18、=0;j8;j+)P0=0xff;P0=DSY_CODEj; /发送段码P2=DSY_IDXj; /发送位码DelayMS(2);P2=0x00; /关闭所有数码管并延时DelayMS(1000);10 8只数码管滚动显示数字串电路如上图/*名称：8只数码管滚动显示数字串说明：数码管向左滚动显示3个字符构成的数字串#include#include#define uchar unsigned char#define uint unsigned int/段码表uchar code DSY_CODE=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,

19、0xff;/下面数组看作环形队列，显示从某个数开始的8个数（10表示黑屏）uchar Num=10,10,10,10,10,10,10,10,2,9,8;/延时void DelayMS(uint x)uchar t;while(x-) for(t=0;t120;t+);/主程序void main()uchar i,j,k=0,m=0x80;while(1)/刷新若干次，保持一段时间的稳定显示for(i=0;i15;i+)for(j=0;j8;j+)/发送段码，采用环形取法，从第k个开始取第j个P0=0xff;P0=DSY_CODENum(k+j)%11; m=_crol_(m,1);P2=m;

20、 /发送位码DelayMS(2);k=(k+1)%11;/环形队列首支针k递增，Num下标范围010，故对11取余11 K1-K4 控制LED移位/*名称：K1-K4 控制LED移位说明：按下K1时，P0口LED上移一位； 按下K2时，P0口LED下移一位； 按下K3时，P2口LED上移一位； 按下K4时，P2口LED下移一位；#include#include#define uchar unsigned char#define uint unsigned int/延时void DelayMS(uint x)uchar i;while(x-) for(i=0;i120;i+);/根据P1口的按键

21、移动LEDvoid Move_LED()if (P1&0x10)=0) P0=_cror_(P0,1); /K1else if(P1&0x20)=0) P0=_crol_(P0,1);/K2else if(P1&0x40)=0) P2=_cror_(P2,1); /K3else if(P1&0x80)=0) P2=_crol_(P2,1);/K4/主程序void main()uchar Recent_Key;/最近按键P0=0xfe;P2=0xfe;P1=0xff;Recent_Key=0xff;while(1)if(Recent_Key!=P1)Recent_Key=P1; /保存最近按键M

22、ove_LED();DelayMS(10);12 K1-K4 按键状态显示/*名称：K1-K4 按键状态显示说明：K1、K2按下时LED点亮，松开时熄灭， K3、K4按下并释放时LED点亮，再次按下并释放时熄灭；#include#define uchar unsigned char#define uint unsigned intsbit LED1=P00;sbit LED2=P01;sbit LED3=P02;sbit LED4=P03;sbit K1=P10;sbit K2=P11;sbit K3=P12;sbit K4=P13;/延时void DelayMS(uint x)uchar i

23、;while(x-) for(i=0;i120;i+);/主程序void main()P0=0xff;P1=0xff;while(1)LED1=K1;LED2=K2;if(K3=0)while(K3=0);LED3=LED3;if(K4=0)while(K4=0);LED4=LED4;DelayMS(10);13 K1-K4 分组控制LED/*名称：K1-K4 分组控制LED说明：每次按下K1时递增点亮一只LED，全亮时再次按下则再次循环开始， K2按下后点亮上面4只LED，K3按下后点亮下面4只LED，K4按下后关闭所有LED#include#define uchar unsigned ch

24、ar#define uint unsigned int/延时void DelayMS(uint x)uchar i;while(x-) for(i=0;i4;k=0;/检查1所在位置，累加获取按键号kwhile(Key_State!=0)k+;Key_State=1;/根据按键号k进行4种处理switch(k)case 1:if(P0=0x00) P0=0xff;P0=1;DelayMS(200);break;case 2:P0=0xf0;break;case 3:P0=0x0f;break;case 4:P0=0xff;14 K1-K4 控制数码管移位显示/*名称：K1-K4 控制数码管移位

25、显示说明：按下K1时加1计数并增加显示位， 按下K2时减1计数并减少显示位， 按下K3时清零。#include#define uchar unsigned char#define uint unsigned int/段码uchar code DSY_CODE=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0xff;/位码uchar code DSY_Index=0x80,0x40,0x20,0x10,0x08,0x04,0x02,0x01;/待显示到各数码管的数字缓冲（开始仅在0位显示0，其他黑屏）uchar Display_Buffer=

26、0,10,10,10,10,10,10,10;/延时void DelayMS(uint x)uchar i;while(x-) for(i=0;i120;i+);void Show_Count_ON_DSY()uchar i;for(i=0;i8) Key_Counts=8;Display_BufferKey_Counts-1=Key_Counts;break;case 0xfd:if(Key_Counts0)Display_Buffer-Key_Counts=10;break;case 0xfb:Display_Buffer0=0;for(i=1;i8;i+) Display_Bufferi

27、=10;Key_Counts=0;/若键未释放则仅刷新显示，不进行键扫描while(P1!=0xff) Show_Count_ON_DSY();15 K1-K4 控制数码管加减演示/*名称：K1-K4 控制数码管加减演示说明：按下K1后加1计数，按下K2后减1计数，按下K3后清零。#include#include#define uchar unsigned char#define uint unsigned int/段码uchar code DSY_CODE=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0xff;/待显示的3位缓冲ucha

28、r Num_Buffer=0,0,0;/按键代码，按键计数uchar Key_Code,Key_Counts=0;/延时void DelayMS(uint x)uchar i;while(x-) for(i=0;i120;i+);/显示函数void Show_Counts_ON_DSY()uchar i,j=0x01;Num_Buffer2=Key_Counts/100;Num_Buffer1=Key_Counts/10%10;Num_Buffer0=Key_Counts%10;for(i=0;i3;i+)j=_cror_(j,1);P0=0xff;P0=DSY_CODENum_Bufferi

29、;P2=j;DelayMS(1);/主程序void main()uchar i;P0=0xff;P1=0xff;P2=0x00;Key_Code=0xff;while(1)Show_Counts_ON_DSY();P1=0xff;Key_Code=P1;/有键按下时，数码管刷新显示30次，该行代码同时起到延时作用if(Key_Code!=0xff)for(i=0;i30;i+) Show_Counts_ON_DSY();switch(Key_Code)case 0xfe:if(Key_Counts0) Key_Counts-;break;case 0xfb:Key_Counts=0;Key_C

30、ode=0xff;16 4X4矩阵键盘控制条形LED显示/*名称：4X4矩阵键盘控制条形LED显示说明：运行本例时，按下的按键值越大点亮的LED越多。#include#include#define uchar unsigned char#define uint unsigned int/矩阵键盘按键特征码表uchar code KeyCodeTable=0x11,0x12,0x14,0x18,0x21,0x22,0x24,0x28,0x41,0x42,0x44,0x48,0x81,0x82,0x84,0x88;/延时void DelayMS(uint x)uchar i;while(x-) f

31、or(i=0;i120;i+);/键盘扫描uchar Keys_Scan()uchar sCode,kCode,i,k;/低4位置0，放入4行P1=0xf0;/若高4位出现0，则有键按下if(P1&0xf0)!=0xf0)DelayMS(2);if(P1&0xf0)!=0xf0)sCode=0xfe;/行扫描码初值for(k=0;k4;k+)/对4行分别进行扫描P1=sCode;if(P1&0xf0)!=0xf0)kCode=P1;for(i=0;i16;i+)/查表得到按键序号并返回if(kCode=KeyCodeTablei)return(i);elsesCode=_crol_(sCode

32、,1);return(-1);/主程序void main()uchar i,P2_LED,P3_LED;uchar KeyNo=-1;/按键序号，-1表示无按键while(1)KeyNo=Keys_Scan();/扫描键盘获取按键序号KeyNo if(KeyNo!=-1)P2_LED=0xff;P3_LED=0xff;for(i=0;i=KeyNo;i+)/键值越大，点亮的LED越多if(i=1;elseP2_LED=1;P3=P3_LED; /点亮条形LEDP2=P2_LED;17 数码管显示4X4矩阵键盘按键号/*名称：数码管显示4X4矩阵键盘按键号说明：按下任意键时，数码管都会显示其键的

33、序号，扫描程序首先判断按键发生在哪一列，然后根据所发生的行附加不同的值，从而得到按键的序号。#include#define uchar unsigned char#define uint unsigned int/段码uchar code DSY_CODE=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0x88,0x83,0xc6,0xa1,0x86,0x8e,0x00;sbit BEEP=P37;/上次按键和当前按键的序号，该矩阵中序号范围015，16表示无按键uchar Pre_KeyNo=16,KeyNo=16;/延时void Del

34、ayMS(uint x)uchar i;while(x-) for(i=0;i40x0f;/按键后f0变成XXXX0000，X中有1个为0，三个仍为1；高4位转移到低4位并异或得到改变的值switch(Tmp)/对03行分别附加起始值0，4，8，12case 1:KeyNo+=0;break;case 2:KeyNo+=4;break;case 4:KeyNo+=8;break;case 8:KeyNo+=12;/蜂鸣器void Beep()uchar i;for(i=0;i100;i+)DelayMS(1);BEEP=BEEP;BEEP=0;/主程序void main()P0=0x00;BE

35、EP=0;while(1)P1=0xf0;if(P1!=0xf0) Keys_Scan(); /获取键序号if(Pre_KeyNo!=KeyNo)P0=DSY_CODEKeyNo;Beep();Pre_KeyNo=KeyNo;DelayMS(100);18 开关控制LED/*名称：开关控制LED说明：开关S1和S2分别控制LED1和LED2。#includesbit S1=P10;sbit S2=P11;sbit LED1=P00;sbit LED2=P01;/主程序void main()while(1)LED1=S1;LED2=S2;19 继电器控制照明设备/*名称：继电器控制照明设备说明：

36、按下K1灯点亮，再次按下时灯熄灭#include#define uchar unsigned char#define uint unsigned intsbit K1=P10;sbit RELAY=P24;/延时void DelayMS(uint ms)uchar t;while(ms-)for(t=0;t120;t+);/主程序void main()P1=0xff;RELAY=1;while(1)if(K1=0)while(K1=0);RELAY=RELAY;DelayMS(20);20 数码管显示拨码开关编码/*名称：数码管显示拨码开关编码说明：系统显示拨码开关所设置的编码000255#i

37、nclude#include#define uchar unsigned char#define uint unsigned int/各数字的数码管段码（共阴）uchar code DSY_CODE=0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f;/显示缓冲uchar DSY_Buffer3=0,0,0;/延时void DelayMS(uint ms)uchar t;while(ms-)for(t=0;t120;t+);/主程序void main()uchar i,m,Num;P0=0xff;P2=0xff;while(1)m=0xfe;Num=P1;/读取拨码开关的值DSY_Buffer0=Num/100;DSY_Buffer1=Num/10%10;DSY_Buffer2=Num%10;for(i=0;i3;i+)/刷新显示在数码管上m=_crol_(m,1);P2=m;P0=DSY_CODEDSY_Bufferi;DelayMS(1