外文翻译-基于无线传感器网络的智能家居系统设计(共16页).doc

《外文翻译-基于无线传感器网络的智能家居系统设计(共16页).doc》由会员分享，可在线阅读，更多相关《外文翻译-基于无线传感器网络的智能家居系统设计(共16页).doc（16页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上A Simple Energy Model for Wireless Microsensor TransceiversAbstract This paper describes the modelling of shortrange transceivers for microsensor applications. A simple energy model is derived and used to analyze the transceiver battery life. This model takes into account energy dissipa

2、tion during the start-up, receive, and transmit modes. It shows that there is a significant fixed cost in the transceiver energy consumption and this fixed cost can be driven down by increasing the data rate of the transceiver.I. IntroductionWireless microsensor networks can provide short-range conn

3、ectivity with significant fault tolerances. These systems find usage in diverse areas such as environmental monitoring, industrial process automation, and field surveillance. As an example, Table I shows a detailed specification for a sensor system used in a factory machine monitoring environment.Th

4、e major characteristics of a microsensor system are high sensor density, short range transmissions, and low data rate. Depending on the application, there can also be stringent BER and latency requirements. Due to the large density and the random distributed nature of these networks, battery replace

5、ment is a difficult task. In fact,a primary issue that prevents these networks to be used in many application areas is the short battery life. Therefore, maximizing the battery life time of the sensor nodes is important. Figure 1 shows the peak current consumption limit when a 950mAh battery is used

6、 as the energy source. As seen in the figure, battery life can vary by orders of magnitude depending on the duty cycle of each operation. To allow for higher maximum peak current, it is desirable to have the sensor remain in the off-state for as long as possible.However, the latency requirement of t

7、he system dictates how often the sensor needs to be active. For the industrial sensor application described above, the sensor needs to operate every 5ms to satisfy the latency requirement.Assuming that the sensor operates for 100s every 5ms,the duty cycle is 2%. To achieve a one-year battery life, t

8、he peak current consumption must be kept under 5.4mA, which translates to approximately 10mW at 2V supply.This is a difficult target to achieve for sensors that communicate at giga-Hertz carrier frequencies. There has been active research in microsensor networks over the past years. Gupta 1 and Gros

9、sglauser 2 established information theoretic bounds on the capacity of ad-hoc networks. Chang 3 and Heinzelman 4 suggested algorithms to increase overall network life-time by spreading work loads evenly among all sensors. Much of the work in this area, especially those that deal with energy consumpt

10、ion of sensor networks, require an energy model 5. This paper develops a realistic energy model based on the power consumption of a state of the art Bluetoothtransceiver 6. This model provides insights into how to minimize the power consumption of sensor networks and can be easily incorporated into

11、work that studies energy limited wireless sensor networks. The outline of this paper is as follows. Section II derives the transceiver model. Section III applies this model to analyzing the battery life time of the Bluetooth transceiver.Section IV investigates the dependencies in the model and shows

12、 how to modify the design of the Bluetooth transceiver to improve the battery life. Section V shows the battery life improvement realized by applying the results in Section IV. Section VI summarizes the paper.II. Microsensor Transceiver ModellingThis section derives a simple energy model for low pow

13、er microsensors. Figure 2 shows the model of the sensor node.It includes a sensor/DSP unit for data processing, D/A and A/D for digital-to-analog and analog-to-digital conversion, and a wireless transceiver for data communication. The sensor/DSP, D/A, and A/D operate at low frequency and consume les

14、s than 1mW. This is over an order of magnitude less than the power consumption of the transceiver. Therefore, the energy model ignores the contributions from these components. The transceiver has three modes of operation: start-up, receive, and transmit. Each mode will be described and modelled.A. S

15、tart-up ModeWhen the transceiver is first turned on, it takes some time for the frequency synthesizer and the VCO to lock to the carrier frequency. The start-up energy can be modelled as follows:where P LO is the power consumption of the synthesizer and the VCO. The term t start is the required sett

16、ling time. RF building blocks including PA, LNA, and mixer have negligible start-up time and therefore can remain in the off-state during the start-up mode. B. Receive Mode The active components of the receiver includes the low noise amplifier (LNA), mixer, frequency synthesizer, VCO, intermediate-f

17、requency (IF) amplifier (amp), and demodulator (Demod). The receiver energy consumption can be modelled as follows:where P RX includes the power consumption of the LNA,mixer, IF amplifier, and demodulator. The receiver power consumption is dictated by the carrier frequency and the noise and linearit

18、y requirements. Once these parameters are determined, to the first order the power consumption can be approximated as a constant, for data rates up to 10s of Mb/s. In other words, the power consumption is dominated by the RF building blocks that operate at the carrier frequency. The IF demodulator p

19、ower varies with data rate, but it can be made small by choosing a low IF.C. Transmit ModeThe transmitter includes the modulator (Mod), frequency synthesizer and VCO (shared with the receiver), and power amplifier (PA). The data modulates the VCO and produces a FSK signal at the desired data rate an

20、d carrier frequency. A simple transmitter energy model is shown in Equation (3). The modulator consumes very little energy and therefore can be neglected.P LO can be approximated as a constant. P PA depends on additional factors and needs to be modelled more carefully as follows:where is the PA effi

21、ciency, r is the data rate, d is the transmission distance, and n is the path loss exponent. PA is a factor that depends on E b /N O , noise factor F of the receiver, link margin L mar , wavelength of the carrier frequency , and the transmit/receive antenna gains G T ,G R :From Equations (3) and (4)

22、, the transmitter power consumption can be written as a constant term plus a variable term. The energy model thus becomesIII. Bluetooth TransceiverHere we demonstrate how the above model can be used to calculate the battery life time of a Bluetooth transceiver 6. This is one of the lowest power Blue

23、tooth transceivers reported in literature. The energy consumption of the transceiver depends on how it operates. Assuming a 100-bit packet is received and a 100-bit packet is transmitted every 5ms, Figure 3 showsthe transceiver activity within one cycle of operation.The transceiver takes 120s to sta

24、rt up. Operating at 1Mb/s, the receiver takes 100s to receive the packet. The transceiver then switches to the transmit mode and transmits a same-length packet at the same rate. A 10s interval, t switch , between the receive and the transmit mode is allowed to switch channel or to absorb any transie

25、nt behavior. Therefore, the energy dissipated in one cycle of operation is simplyBoth the average power consumption and the duty cycle can be found From Figure 3. Knowing that the transceiver operates at 2V, the life time for a 950mAh battery is calculated to be approximately 2-months.IV. Energy Opt

26、imizationThe microsensor system described in Section I requires a battery life of one year or better. Although the Bluetooth transceiver described in the last section falls short of this requirement, it serves as a starting point for making improvements. This section examines E op in detail and sugg

27、ests ways to increase the battery life by considering both circuit and system improvements.A. Start-up Energy The start-up energy can be a significant part of the total energy consumption, especially when the transceiver is used to send short packets in burst mode. For the Bluetooth transceiver, E s

28、tart accounts for 20% of E op .The start-up energy becomes negligible if the following condition is held true:For the receive/transmit scheme shown in Figure 3, the right hand-side of Equation (8)is evaluated to be approximately 450s. To keep E start an order of magnitude below E op , it is desirabl

29、e to have a start-up time of less than 45s. Cho has demonstrated a 5.8GHz frequency synthesizer im-plementation with a start-up time under 20s 7.B. Power AmplifierThe PA power consumption is given bywhere is the power efficiency and P out is the RF output power. P out can be determined by link-budge

30、t analysis. For a Bluetooth transceiver, the required P out is 1mW 8.This enables a maximum transmission distance of 10 meters, which is adequate for microsensor applications. Note that P out is small as compared to P LO . The Bluetooth transceiver discussed in Section II has a maximum RF output pow

31、er of 1.6mW and a PA power consumption of 10mW, so the efficiency is at 16%. At frequencies around 2GHz, the PA efficiency can vary from 10% 9 to 70% 10 depending on linearity, circuit topology, and technology. Since FSK signal has a constant envelope, nonlinear PAs can be used so that better effici

32、ency can be achieved. As will be shown in the next section, PA efficiency has a significant impact on the battery life.C. Data RateAssuming a packet of length L pkt is transmitted at dat rate r, then the transmit time isThe transmitter energy consumption can be re-written asEquation (12) shows that

33、the contribution of the fixed cost P LO can be reduced by increasing the data rate. The energy per bit, E bit , is defined as E op divided by the total number of bits received and sent during one cycle of operation. Assuming a packet of length L pkt is received and a packet of the same length is tra

34、nsmitted, E bit can be found by dividing Equation (7) by 2L pkt . Substituting the appropriate expressions for E start , E rx , and E tx and re-arranging the terms, we getThe first term in Equation (13) is the start-up energy cost. The second term is the PA energy cost. The third term is the cost of

35、 the rest of the transceiver electronics during the transmit and receive modes. Note that this term is divided by the data rate r. Figure 4 shows E bit as a function of data rate. The two solid curves have start-up time 120s and PA efficiencies 10% and 70%, respectively. The two dotted curves have s

36、tart-up time 20s and efficiencies 10% and 70%, respectively. At low data rate, E bit is dominated by the fixed cost (the 3rd term in Equation (13). At high data rate, the start-up energy and the PA energy dominates, so in order to increase battery life, good circuit design techniques need to be appl

37、ied to minimize the start-up time and to maximize the PA efficiency.Figure 5 shows the impact of PA efficiency on the battery life at a data rate of 10Mb/s. At t start = 120s, the startup energy is so large that the battery life is limited to 7month even if the PA reaches 100% efficiency. At t start

38、 =20s, the battery life is much improved. The PA efficiencyneeds to be higher than about 30% to have a 1-year or better battery life. This is certainly achievable as discussed previously in the PA section.V. Performance ImprovementThere are three apparent results from the previous section. First, th

39、e data rate should be increased to reduce the fixed cost. Second, the start-up time should be minimized. Third, PA efficiency should be maximized. Figure 6 shows the transceiver activity for a transceiver that has 20s start-up time and 10Mb/s data rate. The power consumption of the electronics are k

40、ept the same as in the Bluetooth transceiver except for the PA. The maximum RF output power is set at 10mW to accommodate the higher data rate, and the PA efficiency is assumed to be 50%. The switching time is kept at 10s, although this is a conservative since the switching time is likely to be shor

41、ter for a faster frequency synthesizer. The E op of this transceiver is 8x lower than that of the Bluetooth transceiver. The battery life-time extends from 2-months to approximately1.3 years.VI. ConclusionThis paper describes the modelling of short-range transceivers for wireless sensor applications

42、. This model takes into account energy dissipation during the start-up, transmit, and receive modes. This model is first used to analyze the battery life of a state of the art Bluetooth transceiver, and then it is used to optimize E op . This paper shows that the battery life can be improved signifi

43、cantly by increasing the data rate, reducing the start-up time, and improving the PA efficiency. Increasing the data rate drives down the fixed energy cost of the transceiver. Reducing the start-up time decreases the start-up energy overhead. Improving the PA efficiency lowers the energy per bit cos

44、t of the PA.一个简单的能量无线微传感器的接收机模型摘要本文描述了微传感器的近程的收发器的造型的应用程序。一个简单的能量模型推导并用于分析收发机的电池寿命。这个模型考虑能量耗散在启动期间,接收和传输模式。这表明有一个收发器能耗的重要固定成本和固定成本可以驱动下通过增加数据收发器的速度。I.我的介绍无线微传感器网络可以提供短程连接与重大故障公差。这些系统在多样化的环境监测等领域,找到使用工业过程自动化,和现场监测。作为一个例子,我表显示了一个详细的规范传感器系统在工厂使用机器监控环境。微传感器系统的主要特点是传感器密度高、短距离传输和低数据率。这取决于应用程序,也可以严格的误码率和延迟

45、要求。由于大密度和随机的这些网络的分布式特性,电池更换是一项艰巨的任务。事实上,一个主要的问题,防止这些网络使用在许多应用领域是短的电池寿命。因此,传感器节点的电池寿命时间最大化是非常重要的。图1显示了峰值电流消耗限制在950 mah电池作为能量来源。在图中可以看到,电池寿命可以通过数量级变化取决于每个操作的工作周期。允许更高的最大峰值电流,是理想的传感器保持尽可能的断开状态。然而,系统的延迟要求规定频率传感器需要活跃。对于上述工业传感器应用,传感器需要操作每5女士来满足延时要求。假设传感器运作100年s每5 ms,占空比为2%。达到一年的电池寿命,峰值电流消耗必须保持在5.4,这意味着大约有

46、10 mw 2 v供应。这是一个很难实现的目标在giga-Hertz传感器通信的载波频率。有积极的研究在微传感器网络在过去的几年中。Gupta 和Grossglauser建立了信息理论界限自组网的能力。Chang 和 Heinzelman建议的算法来提高整体网络寿命通过传播工作负载均匀地在所有传感器。在这一领域的大部分工作,特别是那些处理传感器网络的能量消耗,需要一个能量模型。本文发展一个现实的能源模型基于能耗最先进的蓝牙收发器。这个模型提供了见解如何最小化的功耗传感器网络,可以很容易地纳入工作,研究能源有限的无线传感器网络。本文的概述如下。第二节收发器模型。第三节该模型适用于分析蓝牙收发器的

47、电池寿命时间。第四部分调查中的依赖关系模型,并展示了如何修改蓝牙收发器的设计来提高电池寿命。第五部分显示了电池寿命的改进实现了应用结果第四节。第六部分总结了纸。II.微传感器收发器造型本节源于一个简单的低功耗微传感器能量模型。图2显示了传感器节点的模型。它包括一个传感器/ DSP数据处理单元,D / a和a / D数模和模数转换,并为数据通信无线收发器。传感器/ DSP、D / A和A / D操作在低频率和消费不到1兆瓦。这是在一个数量级小于收发器的功耗。因此,能源模型忽略了这些组件的贡献。收发器有三种操作模式:启动,接收和传输。每个模式都将被描述和建模。A. 启动模式收发器是第一次打开时,它

48、需要一些时间和频率合成器VCO载波频率锁定。启动能量可以参照如下:在P LO的功耗是合成器VCO。术语t开始所需的稳定时间。射频构件包括PA、低噪声放大器和混频器的启动时间可以忽略不计,因此可以保持在断开的启动模式。B. 接收模式接收机的活性成分包括低噪声放大器(LNA)、搅拌机、频率合成器VCO,中频放大器(如果)(amp),和解调器(解调)。接收方能源消耗可以参照如下:在P RX包括低噪声放大器的功耗、搅拌机、中频放大器、解调器。接收机功耗是由载波频率和噪声和线性度的要求。一旦确定这些参数,对一阶功耗可以近似为一个常数,为数据率10 Mb / s。换句话说,能耗由射频积木在载波频率。如果解

49、调器功率随数据速率,但它可以小如果通过选择低。C. 传送方式发射机包括调制器(Mod),频率合成器VCO与接收机(共享),和功率放大器(PA)。数据调整VCO的移频键控信号并产生所需的数据率和载波频率。一个简单的发射机能源模型方程(3)所示。调制器消耗很少的能量,因此可以忽略不计。P LO可以近似为一个常数。P PA取决于其他因素,需要更仔细地建模如下:在巴勒斯坦权力机构效率,r是数据速率,d是传输距离,n是路径损耗指数。PA是一个因素,取决于E b / N O,接收机的噪声系数F,链接保证金L mar,载波频率的波长,和发送/接收天线收益G T G R:从方程(3)和(4),发射机功率消耗可以写成一个常数项和一个变量。因此成为能量模型III. 蓝牙发接器在这里我们将演示如何使用上述模