柴油机专用名词英语.doc
《柴油机专用名词英语.doc》由会员分享,可在线阅读,更多相关《柴油机专用名词英语.doc(16页珍藏版)》请在淘文阁 - 分享文档赚钱的网站上搜索。
1、【精品文档】如有侵权,请联系网站删除,仅供学习与交流柴油机专用名词英语曲轴箱Crankcase(bed plate)2机体(气缸体)cylinder-block3油底壳 oil pan4曲轴crankshaft5飞轮壳flywheel housing6活塞环piston ring7油环oil ring8气环gas ring9螺旋弹簧油环spiral spring oil ring10连杆螺栓connecting rod bolt (screw)11前(后)油封front(after) oil seal (gasket)12轴瓦 Shell pin (bearing shell)13止推片Sto
2、p washer14曲拐 Crank throw15曲拐臂body of crank throw16曲柄销crank pin17主轴颈main journal18减振器Vibration damper19齿轮gear /gear wheel20正时齿轮室Gear case21正时齿轮timing gear22中间齿轮intermed wheel (gear)/idle gear23喷油泵齿轮Injection pump gear24凸轮轴齿轮Camshaft wheel(gear)25空压机齿轮Air compressor gear26.传动轴transmission shaft27弹性联接片
3、clamp28高压喷油泵(high-pressure)Injection pump29输油泵fuel supply pump30燃油滤清器fuel filter31滤网strainer screen32高压油管high pressure fuel pipe (injection pipe)33喷油器Injector (nozzle holder)34喷油器压块Pressure clip35供油提前器Advanced mechanism36供油提前角Advanced angle37喷射压力injection pressure38泵端压力 Pump injection pressure39射程 S
4、pray(injection) distance40喷射锥角spray angle41油束spray42油雾颗粒particle43燃烧室Combustion chamber44压缩比compression ratio45压缩余隙Compression gap46火力岸高度47活塞裙部piston skirt48活塞型线49示功图indicator card50排量delivery capacity51化学当量比stoichiometric ratio52空气消耗量air consumption53凸轮轴camshaft54基圆base circle55升程lift range56缓冲段cus
5、hion area(ramp)57配气相位Distribution angle58挺柱Push rod59推杆Handspike/push rod60摇臂rocker61函数凸轮Function cam62几何凸轮Geometrical cam63高次方凸轮64切线凸轮Tangent cam65复摆II型凸轮66定位销assembling pin/fixed pin67压桥68进气门Intake valve69排气门exhaust valve70进气道Intake channel71排气道Exhaust channel72气门座valve seat73水腔water jacket space7
6、4清沙孔Cinder cleaning hole75涡流比swirl ratio76流量系数Flow coefficient77气门升程valve lift78切向气道Tangential channel79螺旋气道Helix channel80挤流81紊流turbulent flow82气门旋转机构valve rotating mechanism(valve train)83锁夹Valve locker(cone)84密封带sealing stripe85湍流overfall /onflow86稀薄燃烧lean combustion87着火点combustion point88燃烧持续期Th
7、e period of combustion(combustion duration)89放热率heat release rate(rate)90燃烧起始角The start angle for(of) combustion 91滞燃期combustion lagging period92后燃afterburning93急燃期strong combustion period94二次喷射secondary injection95压力波动pressure surge96压力室compression chamber97混合气gas mixture98燃烧速率(combustion)burn rate
8、99进气管intake pipe100进气歧管Intake manifold 101排气管Exhaust pipe102进气法兰Intake flange103最高爆发压力Peak fire pressure104平均有效压力mean effective pressure105平均指示压力mean indicated pressure106指示功indicated work107阻尼阀damping delivery valve108减压阀pressure reducing valve109增压器turbocharger110喘振线surge line111压气机(空压机)air compre
9、ssor112涡轮机turbine113蜗壳Turbine case114叶轮impeller115中间壳The middle case116压气机效率The efficient of air compressor117脉冲转换器impulse converter118放气阀air release valve119可变截面喷嘴variable-area nozzle120耐磨环wear ring121废气再循环exhaust gas recycle122进油管Oil pipe123回油管oil return pipe124增压比turbocharging ratio125增压器流量Flow q
10、uantity of turbocharger126硅油离合器silicone oil clutch127主油道 Main office(main oil way)128摩擦付Friction piece129金相组织fine texture130硬度Rigidity(hardness)131抗拉强度tensile strength132延伸率companding rate133疲劳强度fatigue strength134曲柄连杆比135平衡块balance weight /counterbalance136往复质量reciprocating mass137旋转质量Rotating mass
11、138扭振torsional oscillation /torsional vibration139惯量inertia140柔度softness /flexibility141刚度rigidity /stiffness142配器(气)机构valve mechanism143密度density144弹性模量modulus of elasticity145泊松比poisson ratio146振幅swing147谐次148阶rank149共振转速resonance speed150燃油消耗量fuel consumption151燃油消耗率fuel consumption ratio152过量空气系
12、数The excess air ratio153空燃比air /fuel ratio154燃料低热值Lower heating value155烟度smoke156噪声noise157声功率级sound power level158声强级sound intensity level159声压级sound pressure level160本底噪声Back-ground noise161气缸套Cylinder liner/cylinder casing162气缸垫Cylinder head gasket163止口rabbet164火力三角区Fire deck165油耗线法166机械效率mechan
13、ical efficiency167充气效率charge efficiency168测功器dynamometer169排放emission170曲轴转角Crank angle171燃烧率combustion rate172传热系数heat transfer coefficient173压缩多变指数polytropic index of compression174膨胀多变指数polytropic index of expansion175升功率power per litre176机械损失功率mechanical loss power177摩擦功friction work178压缩终点压力com
14、pression terminal pressure179排气背压exhaust back pressure180质量流量mass flow181体积流量volume flow 182湿度Humidity (wetness)183大气压力Atmospheric pressure184排气湿度Exhaust humidity185气缸工作容积working volume of Cylinder186热效率heat efficiency187压力升高比pressure step-up ratio188扫气系数coefficient of scavenging189扭矩储备torque reserv
15、e190最大扭矩点maximum torque point191标定工况点(rated (full )power point)192负荷特性load performance193万有特性(all performance)194外特性Speed performance195推进特性propel performance196台架试验engine test197热力循环thermal circulation198质量守恒conservation of mass199能量守恒conservation of energy200催化转换器catalytic converter201后处理After tre
16、atment202淬火chilling/quench203回火Temper/backfire精炼Refining204退火Annealing205调质处理Heat refining206氮化Nitrogen treatment207电感应淬火Inductive quench208平行度depth of parallelism209同轴度axiality210垂直度verticality211全跳动Jumping 212对称度degree of symmetry213粗糙度Degree of roughness214斜度Pitch(inclination)215锥度taper216位置度Degr
17、ee of position217平面度planeness218直线度straightness accuracy219圆柱度Cylindricity220公差tolerance221尺寸Measurement(dimension)222间隙效应channel effection223喉口直径Throat diameter224丰满系数plump coefficient(fullness ratio)225性能performance226排气制动Exhaust brake铸铁Cast iron227球墨铸铁nodular castiron228耐热铸铁heat resisting iron229
18、灰铸铁gray cast iron230优质碳素钢quality carbon steel231停车手柄shutdown handle232油门拉杆accelerator rod233张紧轮Idler pulley/tension pulley/tensioner234皮带轮Belt Pulleysheave235发电机Dynamo(electric generator)236机油泵oil pump237起动机starter238机油冷却器 oil cooler239空滤器Air cleaner240消音器silencer/muffler241脐子boss /Convex hull 242筋R
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 柴油机 专用 名词 英语
限制150内