可燃气体报警的外文资料翻译(共16页).doc

《可燃气体报警的外文资料翻译(共16页).doc》由会员分享，可在线阅读，更多相关《可燃气体报警的外文资料翻译(共16页).doc（16页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上51系列单片机的结构和功能51系列单片机是英特尔公司生产的具有一定结构和功能的单片机产品。这家公司在1976年引入8位MCS - 48系列单片机后，于1980年又推出了8位高档的MCS - 51系列单片机。它包含很多种这类型的单片机，如8051，8031，8751，80C51BH，80C31BH等，它们的基本组成，基本性能和指令系统都是一样的。一般情况习惯用8051来代表51系列单片机。一个单片机的系统是由以下几部分组成：（1）一个8位CPU微处理器。（2）静态随机存取存储器，能够储存程序运行过程中产生的数据。（3）程序存储器ROM / EPROM中（4KB/8KB）

2、，用来保存程序和一些初始数据。但是在一些单片机中不使用ROM / EPROM中，如8031，8032，80c系列等。（4）4个8排的I / O并行接口P0 P3，每个口可以用作输入，也可以用作输出。（5）2个定时器/计数器，每个定时器/计数器可设置计数用来计数外部事件，可以设置成常用的定时方式，并可以根据计算或结果控制单片机的运行。（6）五个中断源控制系统。（7）1个双向串行I / O口的UART（通用异步接收器/发送器UART），用于实现单片机的串行通信。（8）振荡器和时钟产生电路，需要外部电源的石英晶体微调电路，允许接在12v的振荡频率上。上述部分通过内部数据总线连接。其中，CPU是单片机

3、的核心，它是单片机的控制和指挥中心，ALU算数逻辑运算单元可进行算术运算和逻辑运算，由1个 8暂时存储器，和2个 8位的累加器组成。Acc累加器是ALU运算结果的存放单元，一般数据通过它来传送。此外，Acc往往被视为对8051内的数据传输中转站。和通常的微处理器一样，它是最繁忙的寄存器。有记忆功能并执行命令。该控制器包括程序计数器，可读写的存储器，振荡器和定时电路等。该程序计数器是有两对8或16位计数器，它是一个字节地址计数器，在个人电脑运行程序时，执行下一个单元的内容，程序执行时可以改变它的内容从而改变运行的结果。在8051芯片震荡电路中，需要外接石英晶体和微调电容，其频率范围为1.2MHz

4、12MHz。该脉冲信号，即为8051的工作周期，是最小的时间单位。8051和其他单片机一样，都有相同的控制和功能，就像乐队也有打击乐器一样。在8051中有ROM（程序存储器，只能读取），和RAM（数据存储器，可以读和写），他们有各自独立的内存地址空间，也有相同的处理方式。8051和8751的程序存储器的存储容量为4KB，地址从0000H开始，在使用过程中其中的数据不变。8051、8751、8031数据存储器的内存为128B，默认地址是00FH，用于保存中间数据和缓存。在这128B的内存中，有32 byteses，被称作工作寄存器，和常用的微处理器不同的是，8051的RAM是按功能来划分模块的。

5、MCS - 51系列单片机和一般电脑的处理方式不同。一般电脑会自动分配地址空间，ROM和RAM的计算机可以安排在不同的空间内，地址范围会根据ROM和RAM的位置分配不同地址空间。在访问的内存，不管是ROM和RAM，只有一个地址对应一个内存单元，都要按这个顺序访问。这种内存结构是所谓的普林斯顿结构。 8051的存储器按物理结构划分可分为程序存储器空间和数据存储空间，共有四个内存空间，按结构位置的不同分为内部程序存储空间、外部程序存储空间、内部数据存储空间和外部数据存储空间。但从用户的使用角度看，8051存储器地址空间被分成三类：（1）片内，安排FFFFH的块，片外的（使用16个地址）串口0000

6、H地址。（2）外部数据存储器地址空间为64KB，地址是从0000H到 FFFFH（含16个地址）的位置排列也。（3）256B的数据存储器（使用8个地址）的地址空间。上述三个重叠的内存空间地址，用8051指令系统的传输不同的数据和使用的功能区分。CPU的访问内存时，访问ROM使用MOVC语句，访问RAM块顺序使用片外操作的MOVX语句，访问内存片段使用MOV语句。8051单片机有4个8并行的I / O端口，分别为P0，P1，P2和P3。每个端口是8位精确的双向口，共占了32针。每一个I / O线可作为独立的入口和出口。每个端口包括一个锁存器（即特殊功能寄存器），一个出口驱动器和引进缓冲器。使数据

7、能够锁存输出，数据可以及时缓冲，其余四个具有相同的功能。接外部存储扩大它们的内存时，这四个口就可作为双向口常用的I / O口，这是，P2口看到高8位地址，P0口是一个公共两用口，传送输出低8的地址和数据。P3口的输出级别小于P1，可以在里面绘制负载电阻，每一个都能驱动4个LS型TTL负载输出。作为输入口时，所有TTL或NMOS电路都可以驱动一个正常的方式8051 - P3口作为单片机的P1口。可以利用改变电阻的输出大小，直接地充当震荡开路，不需要添加外部电阻。其中每个口都是标准的双向口。当在当做输入口时，必须把相应的端口置1来锁闭输出。比如8051单片机，所有端口提供的输出电流只能几毫安，用作

8、输出口时接一个普通的晶体管，要稳定使用，还要接一定电阻。其主要功能是把初始地址设为0000H，使单片机从0000H的地址开始运行程序。除了正常进入系统的初始化，由于操作失误或操作过程错误，也要能够解决错误，重新运行。在8051中RST引脚是一个输入复位键，复位键高电平信号有效，要保证24倍以上的时钟周期（即2个机器周期）。如果收到高频的6v输入信号，单片机就会复位。初始化时，需要两部分外部电路。外部电路采用施密特触发方式触发了复位键（RST），形成了复位信号输出电路，并把信号传送到每个引脚，按顺序到了复位引脚，就会迅速响应信号指令。复位功能的可靠性，适合6v电压的电容震荡电路，复位信号的周期可

9、以大于两个机器周期。虽然复位电路的结构很简单，但它的功能是非常重要的。一个单片机系统能否正常运行，应先检查它有没有正确的复位电路。检查和检测其发出信号，用示波器显示时，结合复位电路很重要，观察波形时，输出口（瞬时）的波动范围是很大的，也可以通过复位电路对实验进行有必要的改变。2.外文原文：Structure and function of the MCS-51 series Structure and function of the MCS-51 series one-chip computer MCS-51 is a name of a piece of one-chip computer

10、series which Intel Company produces. This company introduced 8 top-grade one-chip computers of MCS-51 series in 1980 after introducing 8 one-chip computers of MCS-48 series in 1976. It belong to a lot of kinds this line of one-chip computer the chips have,such as 8051, 8031, 8751, 80C51BH, 80C31BH,e

11、tc., their basic composition, basic performance and instruction system are all the same. 8051 daily representatives- 51 serial one-chip computers . An one-chip computer system is made up of several following parts: ( 1) One microprocessor of 8 (CPU). ( 2) At slice data memory RAM (128B/256B),it use

12、not depositting not can reading /data that write, such as result not middle of operation, final result and data wanted to show, etc. ( 3) Procedure memory ROM/EPROM (4KB/8KB ), is used to preserve the procedure , some initial data and form in slice. But does not take ROM/EPROM within some one-chip c

13、omputers, such as 8031 , 8032, 80C ,etc. ( 4) Four 8 run side by side I/O interface P0 four P3, each mouth can use as introduction , may use as exporting too. ( 5) Two timer / counter, each timer / counter may set up and count in the way, used to count to the external incident, can set up into a tim

14、ing way too, and can according to count or result of timing realize the control of the computer. ( 6) Five cut off cutting off the control system of the source . ( 7) One all duplexing serial I/O mouth of UART (universal asynchronous receiver/transmitter (UART) ), is it realize one-chip computer or

15、one-chip computer and serial communication of computer to use for. ( 8) Stretch oscillator and clock produce circuit, quartz crystal finely tune electric capacity need outer. Allow oscillation frequency as 12 megahertas now at most. Every the above-mentioned part was joined through the inside data b

16、us .Among them, CPU is a core of the one-chip computer, it is the control of the computer and command centre, made up of such parts as arithmetic unit and controller , etc. The arithmetic unit can carry on 8 persons of arithmetic operation and unit ALU of logic operation while including one, the 1 s

17、toring device temporarilies of 8, storing device 2 temporarily, 8s accumulation device ACC, register B and procedure state register PSW, etc. Person who accumulate ACC count by 2 input ends entered of checking etc. temporarily as one operation often, come from person who store 1 operation is it is i

18、t make operation to go on to count temporarily , operation result and loopback ACC with another one. In addition, ACC is often regarded as the transfer station of data transmission on 8051 inside . The same as general microprocessor, it is the busiest register. Help remembering that agreeing with A

19、expresses in the order. The controller includes the procedure counter , the order is depositted, the order decipher, the oscillator and timing circuit, etc. The procedure counter is made up of counter of 8 for two, amounts to 16. It is a byte address counter of the procedure in fact, the content is

20、the next IA that will carried out in PC. The content which changes it can change the direction that the procedure carries out . Shake the circuit in 8051 one-chip computers, only need outer quartz crystal and frequency to finely tune the electric capacity, its frequency range is its 12MHZ of 1.2MHZ.

21、 This pulse signal, as 8051 basic beats of working, namely the minimum unit of time. 8051 is the same as other computers, the work in harmony under the control of the basic beat, just like an orchestra according to the beat play that is commanded. There are ROM (procedure memory , can only read ) an

22、d RAM in 8051 slices (data memory, can is it can write ) two to read, they have each independent memory address space, dispose way to be the same with general memory of computer. Procedure 8051 memory and 8751 slice procedure memory capacity 4KB, address begin from 0000H, used for preserving the pro

23、cedure and form constant. Data 8051- 8751 8031 of memory data memory 128B, address false 00FH, use for middle result to deposit operation, the data are stored temporarily and the data are buffered etc. In RAM of this 128B, there is unit of 32 byteses that can be appointed as the job register, this a

24、nd general microprocessor is different, 8051 slice RAM and job register rank one formation the same to arrange the location. It is not very the same that the memory of MCS-51 series one-chip computer and general computer disposes the way in addition. General computer for first address space, ROM and

25、 RAM can arrange in different space within the range of this address at will, namely the addresses of ROM and RAM, with distributing different address space in a formation. While visiting the memory, corresponding and only an address Memory unit, can ROM, it can be RAM too, and by visiting the order

26、 similarly. This kind of memory structure is called the structure of Princeton. 8051 memories are divided into procedure memory space and data memory space on the physics structure, there are four memory spaces in all: The procedure stores in one and data memory space outside data memory and one in

27、procedure memory space and one outside one, the structure forms of this kind of procedure device and data memory separated form data memory, called Harvard structure. But use the angle from users, 8051 memory address space is divided into three kinds: (1) In the slice, arrange blocks of FFFFH , 0000

28、H of location , in unison outside the slice (use 16 addresses). (2) The data memory address space outside one of 64KB, the address is arranged from 0000H 64KB FFFFH (with 16 addresses ) too to the location. (3) Data memory address space of 256B (use 8 addresses). Three above-mentioned memory space a

29、ddresses overlap, for distinguishing and designing the order symbol of different data transmission in the instruction system of 8051: CPU visit slice, ROM order spend MOVC , visit block RAM order uses MOVX outside the slice, RAM order uses MOV to visit in slice. 8051 one-chip computer have four 8 wa

30、lk abreast I/O port, call P0, P1, P2 and P3. Each port is 8 accurate two-way mouths, accounts for 32 pins altogether. Every one I/O line can be used as introduction and exported independently. Each port includes a latch (namely special function register ), one exports the driver and a introduction b

31、uffer . Make data can latch when outputting, data can buffer when making introduction , but four function of passway these self-same. Expand among the system of memory outside having slice, four port these may serve as accurate two-way mouth of I/O in common use. Expand among the system of memory ou

32、tside having slice, P2 mouth see high 8 address off; P0 mouth is a two-way bus, send the introduction of 8 low addresses and data / export in timesharing Output grade , P3 of mouth , P1 of P1 , connect with inside have load resistance of drawing , every one of they can drive 4 Model LS TTL load to o

33、utput. As while inputting the mouth, any TTL or NMOS circuit can drive P1 of 8051 one-chip computers as P3 mouth in a normal way . Because draw resistance on output grade of them have, can open a way collector too or drain-source resistance is it urge to open a way, do not need to have the resistanc

34、e of drawing outerly . Mouths are all accurate two-way mouths too. When the conduct is input, must write the corresponding port latch with 1 first . As to 80C51 one-chip computer, port can only offer milliampere of output electric currents, is it output mouth go when urging one ordinary basing of tr

35、ansistor to regard as, should contact a resistance among the port and transistor base , in order to the electricity while restraining the high level from exporting P1P3 Being restored to the throne is the operation of initializing of an one-chip computer. Its main function is to turn PC into 0000H i

36、nitially , make the one-chip computer begin to hold the conduct procedure from unit 0000H. Except that the ones that enter the system are initialized normally,as because procedure operate it make mistakes or operate there arent mistake, in order to extricate oneself from a predicament , need to be p

37、ressed and restored to the throne the key restarting too. It is an input end which is restored to the throne the signal in 8051 China RST pin. Restore to the throne signal high level effective , should sustain 24 shake cycle (namely 2 machine cycles ) the above its effective times. If 6 of frequency

38、 of utilization brilliant to shake, restore to the throne signal duration should exceed 4 delicate to finish restoring to the throne and operating. Produce the logic picture of circuit which is restored to the throne the signal:Restore to the throne the circuit and include two parts outside in the c

39、hip entirely. Outside that circuit produce to restore to the throne signal (RST ) hand over to Schmitts trigger, restore to the throne circuit sample to output , Schmitt of trigger constantly in each S5P2 , machine of cycle in having one more , then just got and restored to the throne and operated t

40、he necessary signal insidly. Restore to the throne resistance of circuit generally, electric capacity parameter suitable for 6 brilliant to shake, can is it restore to the throne signal high level duration greater than 2 machine cycles to guarantee. Being restored to the throne in the circuit is sim

41、ple, its function is very important. Pieces of one-chip computer system could normal running,should first check it can restore to the throne not succeeding. Checking and can pop ones head and monitor the pin with the oscillograph tentatively, push and is restored to the throne the key, the wave form

42、 that observes and has enough range is exported (instantaneous), can also through is it restore to the throne circuit group holding value carry on the experiment to change.当今社会上，出现了许多煤气报警器，而这些产品大都是针对煤气的泄漏所做出的相应的报警，即为家庭式。但是随着社会的发展，煤气报警器也在发展，也将由单一的家庭式，发展为小区监控。本文就是学习如何对一个小区的煤气泄漏进行监控，并设计了一个监控四个单元的煤气报警系统

43、。煤气报警系统采用了8位8051单片机为系统的CPU，四个单元的煤气浓度对应模拟量利用A/D转换为数字量，并加入了键盘输入。整个系统的硬件电路设计合理，性能安全可靠。 本系统的软件编写采用的是汇编语言，整个程序的思路清晰，考虑全面。可以在执行的开始和过程中，修改报警临界值，增大了使用的地域和领域；在报警时可以指出哪个单元煤气泄漏并且发出音乐，增强了人性化。 关键词电位器采样；报警临界值；煤气浓度 Abstract In the current society, a lot of coal gas alarms have appeared, and these products are most

44、ly to letting out corresponding alarms made of coal gas , it is family. But with the development of society, coal gas alarm develop too, family by a single one too, develop into the district to control. This text studies how to let out and control the coal gas of a district, and has designed a coal

45、gas warning system of controlling four units. Coal gas warning system adopt 8 8051 one-chip computer CPU of system, four coal gas density corresponding analog quantity of unit utilize A/D person who changes figure into, and has joined key in. The hardware circuit of the whole system is reasonable in

46、 design, performance is safe and reliable. What the software of this system is written and adopted is an assembler language , the train of thought of the whole procedure is clear, it is overall to consider. Can revise the warning critical value , has increased the region and field to use in beginnin

47、g and course of carrying out ; Can point out which unit coal gas let out and send out the music while reporting to the police, have strengthened humanization. Keyword The electric potential device sampl 随着“信息时代”的到来，作为获取信息的手段传感器技术得到了显著的进步，其应用领域越来越广泛，对其要求越来越高，需求越来越迫切。传感器技术已成为衡量一个国家科学技术发展水平的重要标志之一。因此，了

48、解并掌握各类传感器的基本结构、工作原理及特性是非常重要的。 为了提高对传感器的认识和了解，尤其是对烟雾传感器的深入研究以及其用法与用途，基于实用、广泛和典型的原则而设计了本系统。本文利用单片机结合传感器技术而开发设计了这一烟雾监控系统。 本论文以电阻式烟雾传感器和单片机技术为核心并与其他电子技术相结合， 设计出一种技术水平较好的烟雾报警器。其中选用MQ-2型半导体可燃气体敏感元件烟雾传感器实现烟雾的检测，具有灵敏度高、响应快、抗干扰能力强等优点，而且价格低廉，使用寿命长。选用的STC12C5410AD单片机，其整合了A/D转换、硬件乘法器、硬件脉宽调制器等资源，具 有高速、低功耗、超强抗干扰等

49、优点，是目前同类技术中性价比较高的产 品。以STC12C5410AD单片机和MQ-2型半导体电阻式烟雾传感器为核心设计的烟雾报警器可实现声光报警、故障自诊断、浓度显示、报警限设置、延时报警及与上位机串口通信等功能。是一种结构简单、性能 稳定、使用方便、价格低廉、智能化的烟雾报警器。具有一定的实用价值。关键词：烟雾，报警器，STC12C5410，传感器AbstractWhile “information age” the arrival, obtained the remarkable progress as the gain information method - - sensor technology, its application domain is more and more widespread, is more and more high to its request, the de