卧加技术协议(共6页).doc

《卧加技术协议(共6页).doc》由会员分享，可在线阅读，更多相关《卧加技术协议(共6页).doc（6页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上 审核编号：ATTACHMENT FOR CONTRACT (TECHNICAL AGREEMENT)合同附件（技术协议）：TECHNICAL AGREEMENT技术协议甲方（买方） ：江苏九龙汽车制造有限公司 The Buyer : Jiagsu Joylong Automobile Co., Ltd. 乙方（卖方） ： The Seller : 丙方（制造商） ： The Maker : 2014年3月12日CONTENT目 录Technical Agreement技术协议书Attachment 1: Supply scope sheet附件一：供货范围Attac

2、hment 2: Machine Specifications附件二：机械参数Attachment 3: NC Unit specification附件三：数控参数Attachment 4: Pre-acceptance Test Record of machine accuracy附件四：机床预验收精度检验书Attachment 5：Technical Proposal附件五：技术方案 TECHNICAL AGREEMENT技术协议Jiagsu Joylong Automobile Co., Ltd. (The End User) will purchase 17sets Horizonta

3、l Machining Centers from, the machine is made by . After full discussion by three sides, we work out the technical agreement as follow: 江苏九龙汽车制造有限公司（需方）设计、制造的卧式加工中心17台，经友好协商就有关技术问题达成如下协议：I. Buyer duty 买方负责： a) After receive the foundation drawing, should finish the foundation in advance. 在收到平面基础图后，提

4、前做好基础 b) is responsible for foundation checking and punching and buyer should help maker to installation and commissioning.负责地基的核实以及地基打孔工作同时买方应配合制造方进行机床的安装与调试。 should provide all necessary foundation components for the machine installation, such as anchor plate leveling plate and chemical bolts提供设备安

5、装所需的所有地脚零件 如地脚垫块，水平调整，化学螺栓等。c) Buyer shall be responsible for machine installation and commission. The buyer will supply the lifting equipment for machine机床安装就位由买方负责并无偿提供起重设备。 II. Maker duty 制造商负责：Provide 17sets Horizontal Machining Center, the type are NHP5500(2 sets)& HC505(15 sets).提供卧式加工中心NHP550

6、0（2台），HC505 （15台）。a) Supply scope供货范围：Refer to Attachment Supply scope sheet 请查阅供货范围附件。b) Standard accessories 标准附件：Refer to Attachment Machine & NC specification 查阅附件机械&NC参数。c) Manual with machine(three sets, English and Chinese language and three sets electrical copy.): maintenance manual, using m

7、anual, operation manual, parts and assembly simple drawing, circuit diagram, ladder diagram, NC instruction, operating manual. 随机说明书（3套,中、英文各3套,电子版3套）：维修说明书、使用说明书、操作说明书、零件及装配示意图、电器图、梯形图、NC说明书、操作手册。 d) should provide the energy (power, compressed air) connection interface data to buyer for install in

8、let and outlet pipes hang down ceiling须提供设备（动力电，压缩空气）的详细接口信息，买方将负责至设备端的电缆和气管的安装。 III. Installation安装:1. 设备到场后由买方负责卸货及安装就位，卖方派人员进行现场支持。2.设备基础采用二次灌浆，二次灌浆水泥由买方提供；卖方提供地脚螺栓，买方按要求准备安装所需的垫块。IV. Acceptance 验收： 1. Standard标准：a) Machine standard机床标准：DICs & DIYs machine tool accuracy testing form, KSB4404 出厂标准

9、。b) Machine accuracy is according to Attachment 4; 机床的精度符合附件4。2. Pre-acceptance 预验收：Including items内容包括：a) Equipment and accessories inspection 设备配套情况；b) Accuracy inspection各项精度检测；c) CNC control system function数控系统各控制功能；d) Provide the report of the pre-acceptance include the above items.提供包括以上各项检测收报

10、告。e) Buyer will send persons to for pre-acceptance and also accept the initial technical training. The period is 5 working days. The charge will be borne by the buyer 买方派人员到工厂预验收及接受卖方的初次技术培训，为期5天。 该费用由买方承担。f) machine 50 pieces of workpiece which were provided by Buyer for testing to meet the require

11、ment during pre-acceptance 预验收期间买方提供50个工件给用于试加工和预验收以满足所提图纸要求。g) Buyer should send * pieces of workpiece to factory within * days after singing the commercial contract, the expenses shall be borne by the buyer. 买方需在4月20日提供设计样件1件，6月25日提供试切件10台，8月10日提供验收件40件至工厂，该费用由买方承担。3. Final acceptance and Training

12、 终验收及培训：1) Final acceptance will be carried out at end-users factory. shall dispatch electrical and mechanical engineers to the end-users factory to supervise the unpacking，installation, commissioning, the final acceptance till the hand over. The end-user should arrange concerning personnel to co-wo

13、rk with makers engineer. 终验收在最终用户工厂进行。应派机电专家到最终用户工厂指导进行开箱、安装、调试及终验收直至交付使用。最终用户应安排有关人员配合工作。The final acceptance include 终验收包括：a) Machine exterior inspection and accessory inspection 机床外观及配置检查。b) Equipment installation设备安装调试: c) Accuracy inspection according to Horizontal Machining center Test Record

14、(Attachment 4) provided by mamufacturer.机床精度检验按照制造商精度检验书（附件4）验收。d) Dry-run 8 hours to check machine performance 空运转8小时，检查机床性能。e) Provide the report of the pre-acceptance include the above items. 提供包括以上各项检测报告。f) Should machine 30 pieces of work-pieces per pallet continuously for detecting machine per

15、formance during final acceptance period， machining process refer to attachment files. 终验收期间连续加工30件/每工作台 工件用于机床性能检测已满足图纸要求,加工内容见附件。g )When the machine is sent to buyer site, will be in charge for final acceptance. At the same time, must train the buyers operators which is held in the buyers site, the

16、 maker is responsible for mechanical maintenance, electrical maintenance, CNC programmers and operators to be trained, until the buyers operators have mastered the equipment maintenance, programming and operating capacities. Training time is 5 days.负责培训甲方人员技术培训。技术培训在买方工厂进行，由负责对买方机械维修人员、电气维修人员、CNC程序编

17、制人员及操作者进行技术培训，直到买方人员能基本掌握设备维修、编程及操作能力为止。时间为5天。h) will send 1 technical engineer to customer site to accompany production with customer after final acceptance, totally time for the accompany period is 30 days.设备终验收完毕后将派遣1名技术工程师到客户工厂进行陪产， 陪产时间累积30天。V. Quality guarantee and After-sales service质量保证和售后服务

18、a) From the date of signing the final acceptance, the equipment warranty is one year, numerical control system warranty is two years, during the quality guarantee period, if any parts was damaged, should be replaced free of charge within 20 days( if there is no inventory in factory then we can not p

19、romise) until the equipments runs well.自最终验收签字之日起，对该设备质保一年，数控系统质保两年。在质量保证期内，如有零部件损坏，应在20天（如工厂没有库存，则最长需要3个月）内无偿更换，直至该设备正常运行. b) The after service must be borne by. must give the technical advice if receiving buyers equipment problems within 4 hours，and when a quality problem coming up, engineer shoul

20、d arrive at the site within 24 hours to resolve faults, the service shall not be contrary to their service mode and commitment. 设备的售后服务由负责.必须在买方设备出现问题后的4小时内 响应用户的技术咨询，若发生质量问题，工程师应在24小时内到达现场解决故障，售后服务不得违背其服务方式和承诺.c) After machine warranty period, required to provide extensive benefits of technical sup

21、port.。 机床保修期过后，要求能提供广泛优惠的技术支持。d) This agreement is become effective after sign by three sides. Others not mention things should be kindly discussion by three sides.本协议待合同签字后同时生效。未尽事宜三方协商解决。甲方（买方） ：江苏九龙汽车制造有限公司 The Buyer : Jiagsu Joylong Automobile Co., Ltd. 签字(Signature)：日期:乙方（卖方） ： The Seller : 签字(Signature)：日期:丙方（制造商） ： The Maker : 签字(Signature)：日期:专心-专注-专业