冲压模具毕业设计英文原文和汉语翻译(完整版).docx

《冲压模具毕业设计英文原文和汉语翻译(完整版).docx》由会员分享，可在线阅读，更多相关《冲压模具毕业设计英文原文和汉语翻译(完整版).docx（16页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、冲压模具毕业设计英文原文和汉语翻译(完整版) Heat Treatment of Die and Mould Oriented Concurrent Design LI Xiong,ZHANG Hong-bing,RUAN Xueyu,LUO Zhonghua,ZHANG Yan Abstract: Many disadvantages exist in the traditional die design method which belongs to serial pattern. It is well known that heat treatment is highly importa

2、nt to the dies. A new idea of concurrent design for heat treatment process of die and mould was developed in order to overcome the existent shortcomings of heat treatment process. Heat treatment CAD/CAE was integrated with concurre nt circumstance and the relevant model was built. These investigatio

3、ns can remarkably improve efficiency, reduce cost and ensure quality of R and D for products. Key words:die design; heat treatment; mould Traditional die and mould design,mainly by experience or semiexperience，is isolated from manufacturing process.Before the design is finalized，the scheme of die an

4、d mould is usually modified time and again，thus some disadvantages come into being,such as long development period,high cost and uncertain practical effect.Due to strong desires for precision,service life,development period and cost,modern die and mould should be designed and manufactured perfectly.

5、Therefore more and more advanced technologies and innovations have been applied,for example,concurrent engineering,agile manufacturing virtual manufacturing,collaborative design,etc. Heat treatment of die and mould is as important as design,manufacture and assembly because it has a vital effect on m

6、anufacture，assembly and service lifeDesign and manufacture of die and mould have progressed rapidly，but heat treatment lagged seriously behind themAs die and mould industry develops，heat treatment must ensure die and mould there are good state of manufacture，assembly and wearresistant properties by

7、request. Impertinent heat treatment can influence die and mould manufacturing such as overhard andsoft and assemblyTraditionally the heat treatment process was made out according to the methods and properties brought forward by designerThis could make the designers of die and mould and heat treatmen

8、t diverge from each other，for the designers of die and mould could not fully realize heat treatment process and materials properties，and contrarily the designers rarely understood the service environment and designing thought. These divergences will impact the progress of die and mould to a great ex

9、tent. Accordingly，if the process design of heat treatment is considered in the early designing stage，the aims of shortening development period，reducing cost and stabilizing quality will be achieved and the sublimation of development pattern from serial to concurrent will be realized Concurrent engin

10、eering takes computer integration system as a carrier,at the very start subsequent each stage and factors have been considered such as manufacturing，heat treating，properties and so forth in order to avoid the errorThe concurrent pattern has dismissed the defect of serial pattern,which bring about a

11、revolution against serial pattern In the present workthe heat treatment was integrated into the concurrent circumstance of the die and mould development，and the systemic and profound research was performed 1 Heat Treatment Under Concurrent Circumstance The concurrent pattern differs ultimately from

12、the serial pattern(see Fig1).With regard to serial pattern，the designers mostly consider the structure and function of die and mould，yet hardly consider the consequent process，so that the former mistakes are easily spread backwardsMeanwhile，the design department rarely communicates with the assembli

13、ng，cost accounting and sales departmentsThese problems certainly will influence the development progress of die and mould and the market foregroundWhereas in the concurrent pattern，the relations among departments are close，the related departments all take part in the development pro gress of die and

14、 mould and have close intercommunion with purchasersThis is propitious to elimination of the conflicts between departments，increase the efficiency and reduce the cost Heat treatment process in the concurrent circumstance is made out not after blueprint and workpiece taken but during die and mould de

15、signingIn this way，it is favorable to optimizing the heat treatment process and making full use of the potential of the materials 2 Integration of Heat Treatment CADCAE for Die and Mould It can be seen from Fig2 that the process design and simulation of heat treatment are the core of integration fra

16、meAfter information input via product design module and heat treatment process generated via heat treatment CAD and heat treatment CAE module will automatically divide the mesh for parts drawing，simulation temperature field microstructure analysis after heattreatment and the defect of possible emerg

17、ing (such as overheat,over burning)，and then the heat treatment process is judged if the optimization is made according to the result reappeared by stereoscopic vision technologyMoreover tool and clamping apparatus CAD and CAM are integrated into this system The concurrent engineering based integrat

18、ion frame can share information with other branchThat makes for optimizing the heat treatment process and ensuring the process sound 2.1 3-D model and stereoscopic vision technology for heat treatment The problems about materials，structure and size for die and mould can be discovered as soon as poss

19、ible by 3-D model for heat treatment based on the shape of die and mouldModeling heating condition and phase transformation condition for die and mould during heat treatment are workable，because it has been broken through for the calculation of phase transformation thermodynamics，phase transformatio

20、n kinetics，phase stress,thermal stress，heat transfer，hydrokinetics etcFor example，3-D heat conducting algorithm models for local heating complicated impression and asymmetric die and mould，and M ARC software models for microstructure transformation was usedComputer can present the informations of te

21、mperature，microstructure and stress at arbitrary time and display the entire transformation procedure in the form of 3-D by coupling temperature field,microstructure field and stress fieldIf the property can be coupled,various partial properties can be predicted by computer 2.2 Heat treatment proces

22、s design Due to the special requests for strength，hardness，surface roughness and distortion during heat treatment for die and mould，the parameters including quenching medium type，quenching temperature and tempering temperature and time，must be properly selected，and whether using surface quenching or

23、 chemical heat treatment the parameters must be rightly determinedIt is difficult to determine the parameters by computer fullySince computer technology develops quickly in recent decades,the difficulty with largescale calculation has been overcomeBy simulating and weighing the property，the cost and

24、 the required period after heat treatmentit is not difficult to optimize the heat treatment process 2.3 Data base for heat treatment A heat treatment database is described in Fig3The database is the foundation of making out heat treatment processGenerally，heat treatment database is divided into mate

25、rials database and process databaseIt is an inexorable trend to predict the property by materials and processAlthough it is difficult to establish a property database，it is necessary to establish the database by a series of testsThe materials database includes steel grades,chemical compositions，prop

26、erties and home and abroad grades parallel tablesThe process database includes heat treatment criterions，classes，heat preservation time and cooling velocityBased on the database，heat treatment process can be created by inferring from rules 2.4 Tool and equipment for heat treatment After heat treatme

27、nt process is determined，tool and equipment CADCAE system transfers the information about design and manufacture to the numerical control deviceThrough rapid tooling prototype，the reliability of tool and the clamping apparatus can be judgedThe whole procedure is transferred by network，in which there

28、 is no manmade interference 3 Key Technique 3.1 Coupling of temperature，microstructure，stress and property Heat treatment procedure is a procedure of temperature-microstructurestress interactionThe three factors can all influence the property (see Fig4)During heating and cooling，hot stress and trans

29、formation will come into being when microstructure changes.Transformation temperature-microstructure and temperaturemicrostructureand stress-property interact on each otherResearch on the interaction of the four factors has been greatly developed,but the universal mathematic model has not been built

30、Many models fit the test nicely，but they cannot be put into practiceDifficulties with most of models are solved in analytic solution，and numerical method is employed so that the inaccuracy of calculation exists Even so，comparing experience method with qualitative analysis，heat treatment simulation b

31、y computer makes great progress 3.2 Establishment and integration of models The development procedure for die and mould involves design,manufacture，heat treatment，assembly，maintenance and so onThey should have own database and mode1They are in series with each other by the entityrelation modelThroug

32、h establishing and employing dynamic inference mechanism ，the aim of optimizing design can be achievedThe relation between product model and other models was builtThe product model will change in case the cell model changesIn fact，it belongs to the relation of data with die and mouldAfter heat treat

33、ment model is integrated into the system，it is no more an isolated unit but a member which is close to other models in the systemAfter searching，calculating and reasoning from the heat treatment database,procedure for heat treatment，which is restricted by geometric model,manufacture model for die an

34、d mould and by cost and property，is obtainedIf the restriction is disobeyed，the system will send out the interpretative warning All design cells are connected by communication network 3.3 Management and harmony among members The complexity of die and mould requires closely cooperating among item gro

35、upsBecause each member is short of global consideration for die and mould development，they need to be managed and harmonizedFirstly,each item group should define its own control condition and resource requested,and learn of the request of up-and-down working procedure in order to avoid conflictSecon

36、dly，development plan should be made out and monitor mechanism should be establishedThe obstruction can be duly excluded in case the development is hindered Agile management and harmony redound to communicating information，increasing efficiency，and reducing redundancyMeanwhile it is beneficial for ex

37、citing creativity，clearing conflict and making the best of resource 4 Conclusions (1) Heat treatment CADCAE has been integrated into concurrent design for die and mould and heat treatment is graphed,which can increase efficiency，easily discover problems and clear conflicts (2) Die and mould developm

38、ent is performed on the same platformWhen the heat treatment process is made out，designers can obtain correlative information and transfer self-information to other design departments on the platform (3) Making out correct development schedule and adjusting it in time can enormously shorten the deve

39、lopment period and reduce cost References： 1 ZHOU Xiong-hui，PENG Ying-hongThe Theory and Technique of Modern Die and Mould Design and ManufactureMShanghai：Shanghai Jiaotong University Press 2000(in Chinese) 2 Kang M，Park& Computer Integrated Mold ManufacturingJInt J Computer Integrated Manufacturing

40、，1995，5：229-239 3 Yau H T，Meno C HConcurrent Process Planning for Finishing Milling and Dimensional Inspection of Sculptured Surface in Die and Mould ManufacturingJInt J Product Research，1993，31(11)：270927254 LI Xiang，ZHOU Xiong-hui，RUAN Xue-yuApplication of Injection Mold Collaborative Manufacturin

41、g System JJournaI of Shanghai Jiaotong University，2000，35(4)：1391-1394 5 Kuzman K，Nardin B，Kovae M ,et a1The Integration of Rapid Prototyping and CAE in Mould Manufacturing JJ Materials Processing Technology，2022，111：279285 6 LI Xiong，ZHANG Hongbing，RUAN Xue-yu，et a1Heat Treatment Process Design Ori

42、ented Based on Concurrent EngineeringJJournal of Iron and Steel Research，2022，14(4)：2629 文献出处： LI Xiong,ZHANG Hong-bing,RUAN Xueyu,LUO Zhonghua,ZHANG Yan.Heat Treatment of Die and Mould Oriented Concurrent DesignJ.Journal of Iron and Steel Research，2022,13(1):40-43，74 模具热处理及其导向平行设计 李雄，张鸿冰，阮雪榆，罗中华，张艳

43、 摘要： 在一系列方式中，传统模具设计方法存在许多缺点。众所周知,热处理对模具起着非常重要的作用。为了克服模具热处理工艺存在的缺点，一种新的模具热处理工艺并行设计方法已经被开发出来了。 热处理CAD/CAE技术是集成了并行环境和有关模型而建立的。这些调查研究可以显著提高效率，降低成本，并保证产品质量达到R和D级。 关键词：模具设计；热处理；模具 传统模具设计主要是依照自身实践经验或依照部分实践经验，而不是制造工艺。在设计完成之前，模具方案通常要被一次又一次的改进，于是有些缺点便出现，例如开发时期长，成本高和实际效果不明显。由于对精确性、使用寿命、开发期和费用的严格要求，先进的模具要求设计和制造

44、得十分完善。因此越来越先进的技术和创新方法被应用其中，例如并行工程、敏捷制造业、虚拟制造业、协同合作设计等。 模具的热处理与模具设计，制造和装配同样重要。因为它对模具的制造装配和使用寿命又及其重要的影响。模具设计与制造发展十分迅速，但是热处理发展却严重滞后它们。随着模具工业的发展，热处理必须保证模具有良好的制造装配和磨损耐热性能。不切实际的热处理将导致模具材料过硬或过软，同时影响模具装配性能。传统的热处理工艺是按照设计师提出的方法和特性制作出来的。这样会使模具设计师和热处理工艺师意见产生分歧，而模具设计师却不能充分地了解热处理工艺和材料的性能，相反热处理工艺师却很少了解模具的使用环境和设计思路

45、。这些分歧将在很大程度上影响模具的发展。因此，如果把热处理工艺设计放在设计阶段之前，则缩短开发周期，减少花费和保证质量等目标将会被考虑，而且从串行到并行的发展模式也将会实现。 并行工程是以计算机集成系统作为载体，在开始以后，每个阶段和因素都被看作如制造、热处理、性能等等，以避免出现错误。并行模式已经摒除了串行模式的缺陷，由此带来了一场对串行模式的革命。 在当前的工作中，热处理被集成到了模具开发的并行环境中，同时也正在进行这种系统性和深入性的研究。 1.热处理下的并行环境 并行模式与串行模式存在根本的不同（见图1）。对于串行模式，设计者大多考虑的是模具的结构与功能，但很难考虑相关的工艺，以致前者的错误很容易蔓延到后面。与此同时，设计本门很少与装配，预算会计和销售部门沟通。这些问题当然会影响模具的开发进度和市场前景。然而在并行模式中，不但以上部门关系联系密切，所有参加模具开发的部门都与买家有密切的交流。这有助于协调各部门消除矛盾，提高工作效率，同时降低成本。 (a) (b) (a)串行模式（b）并行模式 图1.基于摸具开发的串行工程与并行工程系统框架示意图