汽车行业常用缩写.doc

《汽车行业常用缩写.doc》由会员分享，可在线阅读，更多相关《汽车行业常用缩写.doc（3页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精品文档，仅供学习与交流，如有侵权请联系网站删除Glossary of Terms术语Glossary of Terms术语AAR: Appearance Approval Report 外观批准报告A/D/V: Analysis/Development/Validation 分析/开发/验证A/D/VDV: ADV Design Validation ADV设计验证A/D/V P&R: Analysis/Development/Validation Plan and Report. This form is used to summarize the plan and results for

2、 validation testing. Additional information can be found in the GP-11 procedure.分析/开发/验证计划和报告A/D/VPV: ADV Product Validation ADV产品验证AIAG: Automotive Industries Action Group, an organization formed by General Motors, Ford and Daimler-Chrysler to develop common standards and expectations for automotiv

3、e suppliers. 汽车工业行动集团AP: Advance Purchasing 先期采购APQP: Advanced Product Quality Planning 产品质量先期策划APQP Project Plan: A one-page summary of the SGM APQP process that describes the tasks and the timeframe in which they occur. APQP项目策划AQC: Attribute Quality Characteristic 属性质量特性ASQE: Advanced Supplier Qu

4、ality Engineer 先期供应商质量工程师BIW: Body in White. Usually the bare metal shell of the body including doors and deck lid prior to paint and trim. 白车身BOM: Bill of Materials 材料清单BOP: Bill of Process 过程清单Brownfield Site: An expansion of an existing facility. 扩建场地CMM: Coordinate Measuring Machine 三坐标测试仪Cpk: C

5、apability Index for a stabile process 过程能力指数CTC: Component Timing Chart (DRE document) 零部件时间表(DRE文件)CTS: Component Technical Specifications 零部件技术规范CVER: Concept Vehicle Engineering Release 概念车工程发布DC: Design Complete 设计完成Defect outflow detection: A phrase used in the Supplier Quality Statement of Req

6、uirements that refers to in-process or subsequent inspection used to detect defects in parts. 缺陷检测DFM/DFA: Design for Manufacturability / Design for Assembly 可制造性/可装配性设计DFMEA: Design Failure Modes and Effects Analysis. It is used to identify the potential failure modes of a part, associated with the

7、 design, and establish a priority system for design improvements. 设计失效模式和后果分析DPV: Defects per vehicle 每辆车缺陷数DR: Documentation Required DR特性DRE: Design Release Engineer 设计释放工程师DV: Design Validation 设计验证E&APSP: Engineering & Advance Purchasing Sourcing Process. 工程&先期采购定点程序EP: E-Procurement 电子采购流程Error

8、 Occurrence Prevention: A phrase used in the Supplier Quality Statement of Requirements that refers to poke yoke or error-proofing devices used to prevent errors in the manufacturing process from occurring. 防错FTQ: First Time Quality 一次通过质量GA: General Assembly 总装GD&T: Geometric Dimensioning & Toleran

9、cing 几何尺寸与公差SGM: Shanghai General Motors 上海通用汽车GMAP: General Motors Asian Pacific 通用汽车亚太GME: General Motors Europe 通用汽车欧洲GMNA: General Motors North American 通用汽车北美GP: General Procedure 通用程序GPDS: Global Product Description System 全球产品描述系统GPS: Global Purchasing System 全球采购系统GPSC: Global Purchasing & S

10、upplier Chain 全球采购及供应链GR&R: Gage Repeatability and Reproducibility 检具重复性及再现性Greenfield Site: A new supplier facility that is built to support a program.GVDP: Global Vehicle Development Process 全球整车开发流程IPTV: Incidents per Thousand Vehicles 每千辆车故障IVER: Integration Vehicle Engineering Release 集成车工程发布KC

11、C: Key Control Characteristics. It is a process characteristic where variation can affect the final part and/or the performance of the part. 关键控制特性KCDS: Key Characteristic Designation System 关键特性指示系统Kick-Off Meeting: The first APQP supplier program review. 启动会议(第一次APQP供应商项目评审)KPC: Key Product Charac

12、teristic. It is a product characteristic for which reasonably anticipated variation could significantly affect safety, compliance to governmental regulations, or customer satisfaction. 关键产品特性 LAAM: (General Motors) Latin American, Africa & Meddle East (通用汽车)拉丁美洲、非洲及中东LCR: Lean Capacity Rate. It is t

13、he GM daily capacity requirement. 正常生产能力MCR: Maximum Capacity Rate. It is the GM maximum capacity requirement. 最大生产能力MOP: Make or Purchase 制造/采购MPC: Material Production Control 物料生产控制MPCE: Material Production Control Europe 欧洲物料生产控制MRD: Material Required Date; date material must be delivered in orde

14、r to allow a build event to begin. 物料需求日期MSA: Measurement Systems Analysis 测量系统分析MVBns: Manufacturing Validation Build non-saleable 非销售车制造验证MVBs: Manufacturing Validation Build saleable 销售车制造验证NBH: New Business Hold 停止新业务N.O.D.: Notice of Decision 决议通知OEM: Original Equipment Manufacturer 主机客户PAD: Pr

15、oduction Assembly Documents 生产装配文件PC&L: Production Control & Logistics 生产控制&物流PDT: Product Development Team 产品开发小组PFMEA: Process Failure Modes and Effects Analysis. It is used to identify potential failure modes associated with the manufacturing and assembly process. 过程失效模式和后果分析PPAP: Production Part

16、 Approval Process 生产件批准程序Ppk: Performance index for a stable process 过程能力指数PPM: 1) Program Purchasing Manager, 2) Parts per Million (rejects and returns to suppliers) 1)项目经理 2)每百万件的产品缺陷数PPV: Product & Process Validation 产品及过程验证PQC: Product Quality Characteristic 产品质量特性PR/R: Problem Reporting & Resol

17、ution 问题报告及解决PSA: Potential Supplier Assessment, a subset of the Quality System Assessment (QSA) 潜在供应商评审PV: Product Validation 产品验证QSA: Quality System Assessment 质量体系评审QSB: Quality Systems Basics 质量体系基础QTC: Quoted Tool Capacity 工装报价能力RASIC: Responsible, Approve, Support, Inform, Consult 负责、批准、支持、通知、

18、讨论RR: Run at Rate 按节拍生产RFQ: Request For Quotation 报价要求RPN: Risk Priority Number related to FMEA development 风险顺序数RPN Reduction Plan: An action plan that describes what is being done to reduce the risk priority number for items listed in the DFMEA or PFMEA. 降低RPN值计划SDE: Supplier Development Engineer

19、供应商开发工程师SFMEA: System Failure Mode and Effects Analysis 系统失效模式分析SMT: System Management Team 系统管理小组SOA: Start of Acceleration 加速开始SORP: Start of Regular Production 正式生产SOR: Statement of Requirements 要求声明SPC: Statistical Process Control 统计过程控制SPO: (General Motors) Service and Parts Operations (通用汽车)零件

20、与服务分部SQ: Supplier Quality 供应商质量SQE: Supplier Quality Engineer 供应商质量工程师SQIP: Supplier Quality Improvement Process 供应商质量改进过程SSF: Start of System Fill 系统填充开始SSTS: Sub-system Technical Specifications 子系统技术规范Sub-Assembly / Sub-System: An assembly of sub-components delivered to the SGM main production lin

21、e for installation to the vehicle as a single unit. Subcontractor: The supplier of a sub-component to a Complex System/Subassembly supplier (Tier 2, 3, etc). 分供方SVE: Sub-System Validation Engineer 子系统验证工程师SVER: Structure Vehicle Engineering Release. 结构车工程发布Team Feasibility Commitment: An AIAG APQP f

22、orm that is provided with the Request for Quotation. It is the suppliers concerns with the feasibility of manufacturing the part as specified. 小组可行性承诺TKO: Tooling Kick-Off 模具启动会议UG: Unigraphics UG工程绘图造型系统VLE: Vehicle Line Executive 车辆平台负责人VTC: Validation Testing Complete 验证试验完成EWO: Engineering Work Order 工程工作指令【精品文档】第 3 页