基于压降型PWM开关电源的建模、仿真和减少传导性电磁干扰II-外文翻译.docx

《基于压降型PWM开关电源的建模、仿真和减少传导性电磁干扰II-外文翻译.docx》由会员分享，可在线阅读，更多相关《基于压降型PWM开关电源的建模、仿真和减少传导性电磁干扰II-外文翻译.docx（29页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、Modeling, Simulation, and Reduction of Conducted Electromagnetic Interference Due to a PWM Buck Type Switching Power Supply I A. Farhadi Abstract:Undesired generation of radiated or conducted energy in electrical systems is called Electromagnetic Interference (EMI). High speed switching frequency in

2、 power electronics converters especially in switching power supplies improves efficiency but leads to EMI. Different kind of conducted interference, EMI regulations and conducted EMI measurement are introduced in this paper. Compliancy with national or international regulation is called Electromagne

3、tic Compatibility (EMC). Power electronic systems producers must regard EMC. Modeling and simulation is the first step of EMC evaluation. EMI simulation results due to a PWM Buck type switching power supply are presented in this paper. To improve EMC, some techniques are introduced and their effecti

4、veness proved by simulation. Index Terms:Conducted, EMC, EMI, LISN, Switching Supply I. INTRODUCTION FAST semiconductors make it possible to have high speed and high frequency switching in power electronics . High speed switching causes weight and volume reduction of equipment, but some unwanted eff

5、ects such as radio frequency interference appeared . Compliance with electromagnetic compatibility (EMC) regulations is necessary for producers to present their products to the markets. It is important to take EMC aspects already in design phase . Modeling and simulation is the most effective tool t

6、o analyze EMC consideration before developing the products. A lot of the previous studies concerned the low frequency analysis of power electronics components . Different types of power electronics converters are capable to be considered as source of EMI. They could propagate the EMI in both radiate

7、d and conducted forms. Line Impedance Stabilization Network (LISN) is required for measurement and calculation of conducted interference level . Interference spectrum at the output of LISN is introduced as the EMC evaluation criterion . National or international regulations are the references for th

8、e evaluation of equipment in point of view of EMC . II. SOURCE, PATH AND VICTIM OF EMI Undesired voltage or current is called interference and their cause is called interference source. In this paper a high-speed switching power supply is the source of interference. Interference propagated by radiat

9、ion in area around of an interference source or by conduction through common cabling or wiring connections. In this study conducted emission is considered only. Equipment such as computers, receivers, amplifiers, industrial controllers, etc that are exposed to interference corruption are called vict

10、ims. The common connections of elements, source lines and cabling provide paths for conducted noise or interference. Electromagnetic conducted interference has two components as differential mode and common mode . A. Differential mode conducted interference This mode is related to the noise that is

11、imposed between different lines of a test circuit by a noise source. Related current path is shown in Fig. 1 . The interference source, path impedances, differential mode current and load impedance are also shown in Fig. 1. B. Common mode conducted interference Common mode noise or interference coul

12、d appear and impose between the lines, cables or connections and common ground. Any leakage current between load and common ground could be modeled by interference voltage source. Fig. 2 demonstrates the common mode interference source, common mode currents Icm1 and Icm2 and the related current path

13、s. The power electronics converters perform as noise source between lines of the supply network. In this study differential mode of conducted interference is particularly important and discussion will be continued considering this mode only. III. ELECTROMAGNETIC COMPATIBILITY REGULATIONS Application

14、 of electrical equipment especially static power electronic converters in different equipment is increasing more and more. As mentioned before, power electronics converters are considered as an important source of electromagnetic interference and have corrupting effects on the electric networks . Hi

15、gh level of pollution resulting from various disturbances reduces the quality of power in electric networks. On the other side some residential, commercial and especially medical consumers are so sensitive to power system disturbances including voltage and frequency variations. The best solution to

16、reduce corruption and improve power quality is complying national or international EMC regulations. CISPR, IEC, FCC and VDE are among the most famous organizations from Europe, USA and Germany who are responsible for determining and publishing the most important EMC regulations. IEC and VDE requirem

17、ent and limitations on conducted emission are shown in Fig. 3 and Fig. 4 . For different groups of consumers different classes of regulations could be complied. Class A for common consumers and class B with more hard limitations for special consumers are separated in Fig. 3 and Fig. 4. Frequency ran

18、ge of limitation is different for IEC and VDE that are 150 kHz up to 30 MHz and 10 kHz up to 30 MHz respectively. Compliance of regulations is evaluated by comparison of measured or calculated conducted interference level in the mentioned frequency range with the stated requirements in regulations.

19、In united European community compliance of regulation is mandatory and products must have certified label to show covering of requirements . IV. ELECTROMAGNETIC CONDUCTED INTERFERENCE MEASUREMENT A. Line Impedance Stabilization Network (LISN)1-Providing a low impedance path to transfer power from so

20、urce to power electronics converter and load. 2-Providing a low impedance path from interference source, here power electronics converter, to measurement port. Variation of LISN impedance versus frequency with the mentioned topology is presented in Fig. 7. LISN has stabilized impedance in the range

21、of conducted EMI measurement . Variation of level of signal at the output of LISN versus frequency is the spectrum of interference. The electromagnetic compatibility of a system can be evaluated by comparison of its interference spectrum with the standard limitations. The level of signal at the outp

22、ut of LISN in frequency range 10 kHz up to 30 MHz or 150 kHz up to 30 MHz is criterion of compatibility and should be under the standard limitations. In practical situations, the LISN output is connected to a spectrum analyzer and interference measurement is carried out. But for modeling and simulat

23、ion purposes, the LISN output spectrum is calculated using appropriate software.For a simple fixed frequency PWM controller that is applied to a Buck DC/DC converter, it is possible to assume the error voltage (ve) changes slow with respect to the switching frequency, the pulse width and hence the d

24、uty cycle can be approximated by (1). Vp is the saw tooth waveform amplitude. A. PWM waveform spectral analysis The normalized pulse train m (t) of Fig. 8 represents PWM switch current waveform. The nth pulse of PWM waveform consists of a fixed component D/fs , in which D is the steady state duty cy

25、cle, and a variable component dn/f sthat represents the variation of duty cycle due to variation of source, reference and load. As the PWM switch current waveform contains information concerning EMI due to power supply, it is required to do the spectrum analysis of this waveform in the frequency ran

26、ge of EMI studies. It is assumed that error voltage varies around Ve with amplitude of Ve1 as is shown in (2). fm represents the frequency of error voltage variation due to the variations of source, reference and load. The interception of the error voltage variation curve and the saw tooth waveform

27、with switching frequency, leads to (3) for the computation of duty cycle coefficients. Maximum variation of pulse width around its steady state value of D is limited to D1. In each period of Tm=1/fm , there will be r=fs/fm pulses with duty cycles of dn. Equation (4) presents the Fourier series coeff

28、icients Cn of the PWM waveform m (t). Which have the frequency spectrum of Fig.9. B-Equivalent noise circuit and EMI spectral analysis To attain the equivalent circuit of Fig.6 the voltage source Vs is replaced by short circuit and converter is replaced by PWM waveform switch current (Iex) as it has

29、 shown in Fig. 10. The transfer function is defined as the ratio of the LISN output voltage to the EMI current source as in (5). The coefficients di, ni (i = 1, 2, , 4) correspond to the parameters of the equivalent circuit. Rc and Lc are respectively the effective series resistance (ESR) and induct

30、ance (ESL) of the filter capacitor Cf that model the non-ideality of this element. The LISN and filter parameters are as follows: CN = 100 nF, r = 5 , l = 50 uH, RN =50 , LN=250 uH, Lf = 0, Cf =0, Rc= 0, Lc= 0, fs =25 kHz The EMI spectrum is derived by multiplication of the transfer function and the

31、 source noise spectrum. Simulation results are shown in Fig. 11. VI. PARAMETERS AFFECTION ON EMI A. Duty Cycle The pulse width in PWM waveform varies around a steady state D=0.5. The output noise spectrum was simulated with values of D=0.25 and 0.75 that are shown in Fig. 12 and Fig. 13. Even harmon

32、ics are increased and odd ones are decreased that is desired in point of view of EMC. On the other hand the noise energy is distributed over a wider range of frequency and the level of EMI decreased . B. Amplitude of duty cycle variation The maximum pulse width variation is determined by D1. The EMI

33、 spectrum was simulated with D1=0.05. Simulations are repeated with D1=0.01 and 0.25 and the results are shown in Fig.14 and Fig.15.Increasing of D1 leads to frequency modulation of the EMI signal and reduction in level of conducted EMI. Zooming of Fig. 15 around 7th component of switching frequency

34、 in Fig. 16 shows the frequency modulation clearly. C. Error voltage frequency The main factor in the variation of duty cycle is the variation of source voltage. The fm=100 Hz ripple in source voltage is the inevitable consequence of the usage of rectifiers. The simulation is repeated in the frequen

35、cy of fm=5000 Hz. It is shown in Fig. 17 that at a higher frequency for fm the noise spectrum expands in frequency domain and causes smaller level of conducted EMI. On the other hand it is desired to inject a high frequency signal to the reference voltage intentionally. D. Simultaneous effect of par

36、ameters Simulation results of simultaneous application of D=0.75, D1=0.25 and fm=5000 Hz that lead to expansion of EMI spectrum over a wider frequencies and considerable reduction in EMI level is shown in Fig. 18. VII. CONCLUSION Appearance of Electromagnetic Interference due to the fast switching s

37、emiconductor devices performance in power electronics converters is introduced in this paper. Radiated and conducted interference are two types of Electromagnetic Interference where conducted type is studied in this paper. Compatibility regulations and conducted interference measurement were explain

38、ed. LISN as an important part of measuring process besides its topology, parameters and impedance were described. EMI spectrum due to a PWM Buck type DC/DC converter was considered and simulated. It is necessary to present mechanisms to reduce the level of Electromagnetic interference. It shown that

39、 EMI due to a PWM Buck type switching power supply could be reduced by controlling parameters such as duty cycle, duty cycle variation and reference voltage frequency. VIII. REFRENCES 1 Mohan, Undeland, and Robbins, “Power Electronics Converters, Applications and Design” 3rd edition, John Wiley & So

40、ns, 2003. 2 P. Moy, “EMC Related Issues for Power Electronics”, IEEE, Automotive Power Electronics, 1989, 28-29 Aug. 1989 pp. 46 53. 3 M. J. Nave, “Prediction of Conducted Interference in Switched Mode Power Supplies”, Session 3B, IEEE International Symp. on EMC, 1986. 4 Henderson, R. D. and Rose, P

41、. J., “Harmonics and their Effects on Power Quality and Transformers”, IEEE Trans. On Ind. App., 1994, pp. 528-532. 5 I. Kasikci, “A New Method for Power Factor Correction and Harmonic Elimination in Power System”, Proceedings of IEEE Ninth International Conference on Harmonics and Quality of Power,

42、 Volume 3, pp. 810 815, Oct. 2000. 6 M. J. Nave, “Line Impedance Stabilization Networks: Theory and Applications”, RFI/EMI Corner, April 1985, pp. 54-56. 7 T. Williams, “EMC for Product Designers” 3rd edition 2001 Newnes. 8 B. Keisier, “Principles of Electromagnetic Compatibility”, 3rd edition ARTEC

43、H HOUSE 1987. 9 J. C. Fluke, “Controlling Conducted Emission by Design”, Vanhostrand Reinhold 1991. 10 M. Daniel,”DC/DC Switching Regulator Analysis”, McGrawhill 1988 11 M. J. Nave,” The Effect of Duty Cycle on SMPS Common Mode Emission: theory and experiment”, IEEE National Symposium on Electromagn

44、etic Compatibility, Page(s): 211-216, 23-25 May 1989. 作者：A. Farhadi国籍：伊朗出处：http:/10.11.248.20:8000/rewriter/EI基于压降型PWM开关电源的建模、仿真和减少传导性电磁干扰IIA. Farhadi作者：A. Farhadi国籍：伊朗出处：http:/10.11.248.20:8000/rewriter/EI摘要：电子设备之中杂乱的辐射或者能量叫做电磁干扰(EMI)。尤其是在开关电源中的电力电子转换器经常高速切换时，虽然提高了工作效率，却导致转换器产生了电磁干扰。在这篇论文之中介绍了各种各样的

45、传导干扰，电磁干扰规章以及传导性电磁干扰的测量。如果电子设备的电磁干扰符合国家或者国际规章称为电磁兼容性（EMC）。电力电子系统生产商一定要重视电子设备的电磁兼容性。电磁兼容性评估的第一步就是建模和仿真。在这篇论文中提出了基于压降型脉宽调制开关电源的电磁干扰仿真结果。为了提高电子设备的电磁兼容性,在论文中介绍了一些技术，并且通过仿真提高了电子设备的工作效率。关键字：传导，电磁兼容性，电磁干扰，线路阻抗稳定网络，开关电源一.前言在电力电子领域中，快速半导体的出现使高速度，高频率的开关切换成为了可能1。高速的开关造成设备的重量和体积的减少，但与此同时这也造成了一些不利的影响，比如无线频率的干扰2。

46、生产商将生产的产品投放到市场，遵守电磁兼容性规章是必要的。在设计阶段考虑电磁兼容性问题是非常重要的3。在开发产品前，建模和仿真是分析电磁兼容性最有效的工具。许多以前的研究都有涉及到电力电子元件的低频分析45。不同类型的电力电子转换器都能够被用来当做电磁的干扰源。电磁干扰源可以通过辐射和传导两种方式来传播。线路阻抗稳定网络被用来测量和计算电磁干扰影响的程度6。线路阻抗稳定网络输出的干扰频谱被引为电磁兼容性的评估标准7,8。国家或国际规章是电子设备电磁兼容性评估的一个参考的方面78。二、来源，途径和电磁干扰的受害者杂乱的电压或者电流被称为干扰，而它们的来源被称为干扰源。本论文中的干扰源就是一个高速

47、的开关电源。干扰通过辐射的方式在干扰源周围传播或通过和常见的电缆或电线连接进行传导。在这项研究中只考虑传导发射设备，如电脑，接收器，放大器，工业控制器等。这些被干扰源辐射的设备被称为受害者。常见的元素，源头接线，布线为噪声以及干扰的传导提供了途径。电磁传导干扰有差模和共模两种干扰方法9。A.差模传导干扰这种模式就是将一个噪声源的噪声施加到一个测试电路的不同线路。它的电路如下图1所示9。在图1中也显示了干扰源，路径阻抗，差模电流以及负载阻抗。 图1差模传导干扰路径B.常见的干扰方式共模噪声或干扰可能出现在电线或者电缆的连接点。负载和接地点的任意泄露都可以被认为是电压干扰源。图2演示了共模干扰源在

48、共模电流为Icm1和Icm2时相关的电流路径9。电力电子转换器可以被用来作为供应网络线路之间的噪音源。在这项研究中不同的传导干扰模式是非常重要的，所以讨论只会在这种模式下被继续考虑。三、电磁兼容性规章电子设备的应用，特别是那些拥有静态电力电子转换器的电子设备越来越多。就像前面讲的一样，电力电子转换器被视为一个重要的电磁干扰源，并能使电网产生腐坏。各种各样的干扰造成的高污染降低了电网电能的质量。另一方面，一些住宅，广告，特别是医疗器件对电力系统的电压及频率变化的干扰非常敏感。最好的解决干扰和提高电能质量的方法就是遵守国家或国际电磁兼容性规定。国际无线电干扰特别委员会，国际电工委员会标准，美国联邦通讯委员会和德国电气工程师协会认证是欧洲，美国，德国最有名的决策并且出版最重要电磁兼容性法规的组织。IEC和VDE在传导发射上的需要和限制如图 3 和图 4所示7,9。 图2共模传导干扰路径图3 IEC管理排放标准不同的消费者群体可以遵守不同类别的规定。A类为普通的消费者，B类为具有更苛刻限制的消费者，在图 3 和图 4这两者被分开。IEC和VDE频率范围不同，前者范围为150 千赫兹 到 30 兆赫兹，后者的范围为10 千赫兹 到 30 兆赫兹，在上述法规规定要求的频率范围内，法规的遵守情况被用来测量或者计算传导干扰的