LED历史及发展现状毕业论文外文翻译.doc

《LED历史及发展现状毕业论文外文翻译.doc》由会员分享，可在线阅读，更多相关《LED历史及发展现状毕业论文外文翻译.doc（9页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、本科生毕业设计（论文）中英文资料英文部分：First LED Summary LED (Light Emitting Diode), light-emitting diode, is a solid state semiconductor devices, which can be directly converted into electricity to light. LED is the heart of a semiconductor chip, the chip is attached to one end of a stent, is the negative side, the

2、other end of the power of the cathode, the entire chip package to be epoxy resin. Semiconductor chip is composed of two parts, part of the P-type semiconductor, it inside the hole-dominated, the other side is the N-type semiconductor, here is mainly electronic. But linking the two semiconductors, am

3、ong them the formation of a PN junction. When the current through the wires role in this chip, will be pushing e-P, P zone in the hole with electronic composite, and then to be issued in the form of photon energy, and this is the principle of LED luminescence. The wavelength of light that is the col

4、or of light, is formed by the PN junction of the decisions of the material. Second LED history and development50 years ago, people have to understand semiconductor materials can produce light of the basic knowledge, the first commercial diodes in 1960. English is the LED light emitting diode (LED) a

5、cronym, and its basic structure is an electroluminescent semiconductor materials, placed in a wire rack, then sealed with epoxy resin around, that is, solid package, Therefore, the protection of the internal batteries can play the role of line, so the seismic performance LED good. LED is the core of

6、 the P-type semiconductor and components of the N-type semiconductor chips, the P-type semiconductor and N-type semiconductor between a transition layer, called the PN junction. In some semiconductor materials in the PN junction, the injection of a small number of carrier-carrier and the majority of

7、 the extra time will be in the form of light energy to release, thus the power to direct conversion of solar energy. PN junction on reverse voltage, a few hard-carrier injection, it is not luminous. This use of injection electroluminescent diodes is produced by the principle of light-emitting diodes

8、, commonly known as LED. When it in a positive state of the work (that is, at both ends with forward voltage), the current flows from the LED anode, cathode, semiconductor crystals on the issue from the ultraviolet to infrared light of different colors, light and the strength of the currents. Instru

9、ments used for the first LED light source instructions, but all kinds of light colored LED lights in traffic and large screen has been widely applied, have a very good economic and social benefits. The 12-inch red traffic lights as an example, is used in the United States have long life, low-efficie

10、ncy 140 watt incandescent lamp as a light source, it produced 2,000 lumens of white light. The red filter, the loss-90 percent, only 200 lumens of red light. In the light of the new design, Lumileds companies have 18 red LED light source, including the loss of circuit, a total power consumption of 1

11、4 watts to generate the same optical effect. Automotive LED lights is also the source of important areas. For general lighting, people need more white light sources. The 1998 white LED successful development. This is the GaN LED chip and Yttrium Aluminum Garnet (YAG) package together cause. GaN chip

12、 of the Blu-ray ( p = 465nm, Wd = 30nm), made of high-temperature sintering of the Ce3 + YAG phosphors excited by this Blu-ray after irradiating a yellow, the peak 550 nm. Blue-chip installed in the LED-based Wanxing reflection in the cavity, covered with a resin mixed with YAG thin layer, about 200

13、-500 nm. LED-based tablets issued by the Blu-ray absorption part of the phosphor, the phosphor another part of the Blu-ray and a yellow light mixed, can be a white. Now, the InGaN / YAG white LED, YAG phosphor by changing the chemical composition of the phosphor layer and adjust the thickness of the

14、 3500-10000 K color temperature can be colored white. This blue LED through the method by white, constructed simple, low-cost, high technology is mature, so use the most. The development of LED display can be divided into the following phases: first phase 1990 to 1995, mainly monochrome and 16 color

15、 graphics screen. Used to display text and simple images, mainly used in railway stations, financial securities, banks, post offices and other public places, as public information display tools. The second stage is from 1995 to 1999, there have been 64, 256 level gray-scale two-color video screen. V

16、ideo control technology, image processing, optical fiber communication technology applications will enhance the LED display to a new level. LED display control LSI chips special at this time developed by domestic companies, and can be applied. The third stage, from 1999, red, pure green, blue LED in

17、 bulk into China, while domestic enterprises in-depth research and development work, using red, green, and blue LED production of full-color display has been widely used , poured into sports stadiums, convention centers, squares and other public places, which will bring the domestic large-screen ful

18、l-color era. With the rapid development of LED materials market, surface mount device is available from 2001, mainly used in indoor full color, and its high brightness, colorful, low temperature characteristics, the point spacing can be adjusted by different price Requirements were accepted, in just

19、 two years time, product sales have more than 300 million yuan, surface mount full-color LED display application market entered the new century. To meet the 2008 Olympic Games, downsizing plan, Liard developed a surface mount dual color displays, a lot of time for the training center and game scorin

20、g. Full color in Olympic venues, in order to tighten investment, full color way is mostly detachable, live during the Olympic Games as a tool can be used for rental after the event, as the performance of national policies such as public places, tools released by In this way cost recovery as soon as

21、possible. On the market, Chinas accession to WTO, Beijings successful Olympic bid and so on, into the development of LED display industry, a new opportunity. Domestic LED display market continues to grow, currently in the domestic market, domestic LED display market share of nearly 95%. LED display

22、the international market capacity is expected to 30% a year growth rate. Currently, LED display manufacturers concentrated primarily in Japan, North America, China LED manufacturers in which the insignificant share of exports. According to incomplete statistics, the world, there are at least 150 man

23、ufacturers full color, in which products are complete, the larger company has some 30 or so.Third LED AdvantagesConductor light-emitting diode (LED) as a third-generation semiconductor lighting source. This fantastic product has a lot of advantages: (1) efficient light: spectra of almost all concent

24、rated in the visible light frequency, the efficiency can reach 80% -90%. The luminous efficiency of incandescent visible light efficiency of almost 10% -20% only. (2) high quality of light: not as a result of spectrum UV and infrared, there is no heat, no radiation, is typically a green light illumi

25、nation. (3) energy consumption of the small: single power generally 0.05-1w, through the cluster can be tailored to meet different needs, and waste very little. As a light source, under the brightness in the same power consumption of only ordinary incandescent 1/8-10. (4) long life: flux attenuation

26、 to 70% of the standard life expectancy is 100,000 hours. A semiconductor light can be used under normal circumstances 50 years, even if the long life of the people, life will be used up to two lights. (5) durable and reliable: No tungsten wire, glass and other easily damaged components, non-normal

27、retirement rate is very small, very low maintenance costs. (6) the application of flexibility: small size, can flat pack, easy to develop into a short thin products, make point, line, face various forms of specific applications. (7) Security: working voltage 1.5-5v or less in between the current 20-

28、70mA in between. (8) green: recyclable waste, no pollution, unlike fluorescent lamps containing mercury as ingredients. (9) response time is short: to adapt to frequent and high-frequency switching operation of occasions. Fourth Classification of LED display 1, color by color can be divided into Sin

29、gle-color display: Single color (red or green). Two-color display: red and green dual-color, 256 gray scale levels, can display 65,536 colors. Full-color screen: red, green, blue color, 256 grayscale full color display can display more than 16 million kinds of colors. 2, according to display device

30、classification LED Digital Display: 7 segment display devices for the digital control code, suitable for production of the clock screen, the interest rate screens, showing the number of electronic display. LED dot-matrix graphic display: display device is arranged by a number of uniform composition

31、of the dot-matrix LED display modules, suitable for broadcast text, image information. LED video display: display devices are formed by a number of light-emitting diodes that can display video, animation and other video files. 3, by using the occasion categories Indoor Display: LED spots smaller, ge

32、neral 3mm - 8mm, shows the general area of a few to more than ten square meters. Outdoor Display: dozens of square meters in size to several hundred square meters, high brightness, can work in the sun, with wind, rain, water resistant. 4, classified according to light spot diameter Indoor screen: 3m

33、m, 3.75mm, 5mm, Room external screen: 10mm, 12mm, 16mm, 19mm, 20mm, 21mm, 22mm, 26mm Room external screen as the basic unit of light emitting tube, LED tube principle is a set of red, green, and blue light-emitting diode sealed in a plastic barrel and jointly develop 5, Display a static, horizontal

34、scroll, vertical scroll and flip display. One block module control drive 12 (up to control 24) 8X8 Dot Matrix, a total of 16X48 dot matrix (or 32X48 dot matrix), is a single block of MAX7219 (or PS7219, HD7279, ZLG7289 and 8279, and the like LED display driver module) 12 times (or 24 times)! Can use

35、 cascade approach the composition of any large dot matrix display. Effects, good power consumption, and the MAX7219 circuit than the use of lower cost. Fifth LED applicationsIt is a semiconductor light-emitting diode by controlling the display, which probably look like that from lots of small red li

36、ghts are usually formed by the bright lights off to show character. Used to display text, graphics, images, animations, quotes, video, video signals and other information on the display screen.Graphic display and LED display into the video display by the LED matrix blocks. Graphic displays can be sy

37、nchronized with the computer display Chinese characters, English text and graphics; video display using micro-computer control, graphics, images, and Mao, real-time, synchronization, clear message to the broadcast of a variety of information dissemination, but also shows two dimensional, three-dimen

38、sional animation, video, TV, VCD programs and live on. LED display shows the screen brightly colored, three-dimensional sense of strong, static, such as painting, moving as the film is widely used in finance, tax, business, telecommunications, sports, advertising, industrial enterprises, transport,

39、education systems, stations, docks, airports, shopping malls, hospitals, hotels, banks, securities markets, construction market, auction houses, industrial enterprises in management and other public places.LED display can show changes in the numbers, text, graphics and video; not only can be used in

40、 the indoor environment can also be used for outdoor environment, with a projector, TV wall, LCD screen can not match advantage.Sixth LED screen test method A look at Screen size, appearance, smoothness, with the screen connection and so on . Second look after the dead pixel screen light up, not in

41、not within the scope of (in general the screen is basically gone now) Color consistency, display text is normal, display pictures, play full screen full color to white, red, green, and blue.中文部分：9一 LED概述LED（Light Emitting Diode），发光二极管，是一种固态的半导体器件，它可以直接把电转化为光。LED的心脏是一个半导体的晶片，晶片的一端附在一个支架上，一端是负极，另一端连接电

42、源的正极，使整个晶片被环氧树脂封装起来。半导体晶片由两部分组成，一部分是P型半导体，在它里面空穴占主导地位，另一端是N型半导体，在这边主要是电子。但这两种半导体连接起来的时候，它们之间就形成一个“P-N结”。当电流通过导线作用于这个晶片的时候，电子就会被推向P区，在P区里电子跟空穴复合，然后就会以光子的形式发出能量，这就是LED发光的原理。而光的波长也就是光的颜色，是由形成P-N结的材料决定的。二 LED历史及发展现状50年前人们已经了解半导体材料可产生光线的基本知识，第一个商用二极管产生于1960年。LED是英文light emitting diode（发光二极管）的缩写，它的基本结构是一块

43、电致发光的半导体材料，置于一个有引线的架子上，然后四周用环氧树脂密封，即固体封装，所以能起到保护内部芯线的作用，所以LED的抗震性能好。 发光二极管的核心部分是由P型半导体和N型半导体组成的晶片，在P型半导体和N型半导体之间有一个过渡层，称为P-N结。在某些半导体材料的PN结中，注入的少数载流子与多数载流子复合时会把多余的能量以光的形式释放出来，从而把电能直接转换为光能。PN结施加反向电压时，少数载流子难以注入，故不发光。这种利用注入式电致发光原理制作的二极管叫发光二极管，通称LED。 当它处于正向工作状态时（即两端加上正向电压），电流从LED阳极流向阴极时，半导体晶体就发出从紫外到红外不同颜

44、色的光线，光的强弱与电流有关。 最初LED用作仪器仪表的指示光源，后来各种光色的LED在交通信号灯和大面积显示屏中得到了广泛应用，产生了很好的经济效益和社会效益。以12英寸的红色交通信号灯为例，在美国本来是采用长寿命、低光效的140瓦白炽灯作为光源，它产生2000流明的白光。经红色滤光片后，光损失90%，只剩下200流明的红光。而在新设计的灯中，Lumileds公司采用了18个红色LED光源，包括电路损失在内，共耗电14瓦，即可产生同样的光效。 汽车信号灯也是LED光源应用的重要领域。 对于一般照明而言，人们更需要白色的光源。1998年白光的LED开发成功。这种LED是将GaN芯片和钇铝石榴石

45、（YAG）封装在一起做成。GaN芯片发蓝光（p=465nm，Wd=30nm），高温烧结制成的含Ce3+的YAG荧光粉受此蓝光激发后发出黄色光射，峰值550nm。蓝光LED基片安装在碗形反射腔中，覆盖以混有YAG的树脂薄层，约200-500nm。 LED基片发出的蓝光部分被荧光粉吸收，另一部分蓝光与荧光粉发出的黄光混合，可以得到得白光。现在，对于InGaN/YAG白色LED，通过改变YAG荧光粉的化学组成和调节荧光粉层的厚度，可以获得色温3500-10000K的各色白光。这种通过蓝光LED得到白光的方法，构造简单、成本低廉、技术成熟度高，因此运用最多。LED显示屏的发展可分为以下几个阶段：第一阶

46、段为1990年到1995年，主要是单色和16级双色图文屏。用于显示文字和简单图片，主要用在车站、金融证券、银行、邮局等公共场所，作为公共信息显示工具。 第二阶段是1995年到1999年，出现了64级、256级灰度的双基色视频屏。视频控制技术、图像处理技术、光纤通信技术等的应用将LED显示屏提升到了一个新的台阶。LED显示屏控制专用大规模集成电路芯片也在此时由国内企业开发出来并得以应用。 第三阶段从1999年开始，红、纯绿、纯蓝LED管大量涌入中国，同时国内企业进行了深入的研发工作，使用红、绿、蓝三原色LED生产的全彩色显示屏被广泛应用，大量进入体育场馆、会展中心、广场等公共场所，从而将国内的大

47、屏幕带入全彩时代。 随着LED原材料市场的迅猛发展，表面贴装器件从2001年面世，主要用在室内全彩屏，并且以其亮度高、色彩鲜艳、温度低的特性，可随意调整的点间距，被不同价位需求者所接受，在短短两年多时间内，产品销售额已超过3亿元，表面贴装全彩色LED显示屏应用市场进入新世纪。为了适应2008年奥运会的“瘦身”计划，利亚德开发了表面贴装双基色显示屏，大量用于训练馆和比赛计时计分系统。在奥运场馆全彩屏方面，为紧缩投资，全彩屏大部分采用可拆卸方式，奥运期间可作为实况转播工具，赛事结束后可用于租赁，作为演出、国家政策发布等公共场合应用工具，通过这种方式可尽快收回成本。 就市场而言，中国加入WTO、北京

48、申奥成功等，成为LED显示屏产业发展的新契机。国内LED显示屏市场保持持续增长，目前在国内市场上，国产LED显示屏的市场占有率近95%。国际上LED显示屏的市场容量预计以每年30%的速度在增长。 目前，LED显示屏的主要制造厂商集中在日本、北美等地，我国LED制造厂商出口的份额在其中微不足道。据不完全统计，世界上目前至少有150家厂商生产全彩屏，其中产品齐全，规模较大的公司约有30家左右。三 LED优点导体发光二极管(LED)作为第三代半导体照明光源。这种产品具有很多梦幻般优点：(1)光效率高：光谱几乎全部集中于可见光频率，效率可以达到80%-90%。而光效差不多的白炽灯可见光效率仅为10%-

49、20%。(2)光线质量高：由于光谱中没有紫外线和红外线，故没有热量，没有辐射，属于典型的绿色照明光源。(3)能耗小：单体功率一般在0.05-1w，通过集群方式可以量体裁衣地满足不同的需要，浪费很少。以其作为光源，在同样亮度下耗电量仅为普通白炽灯的1/8-10。(4)寿命长：光通量衰减到70%的标准寿命是10万小时。一个半导体灯正常情况下可以使用50年，即使长命百岁的人，一生最多也就用2只灯。(5)可靠耐用：没有钨丝、玻壳等容易损坏的部件，非正常报废率很小，维护费用极为低廉。(6)应用灵活：体积小，可以平面封装，易开发成轻薄短小的产品，做成点、线、面各种形式的具体应用产品。(7)安全：单位工作电压大致在1.5-5v之间，工作电流在20-70mA之间。(8)绿色环保：废弃物可回收，没有污染，不像荧光灯一样含有汞成分。(9)响应时间短：适应频繁开关以及高频运作的场合四 LED显示屏的分类 1、