星巴克饮品直营门店工程筹备营建手册 58436-001chigangbei store-第二版DD图纸20130201.pdf

《星巴克饮品直营门店工程筹备营建手册 58436-001chigangbei store-第二版DD图纸20130201.pdf》由会员分享，可在线阅读，更多相关《星巴克饮品直营门店工程筹备营建手册 58436-001chigangbei store-第二版DD图纸20130201.pdf（35页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、ChiGangBei RD.M1822M1522M1822M1522M1522M1822FM1022甲M1022M1422上-0.0500.000-0.150上上0.0000.000上特特同特特特上-1.500-0.050-11-19砌砌突-0.300特特特特商请入口门厅楼梯1详JZ-11扶梯1-4详JZ-19楼梯4详JZ-17商铺开敞楼梯垃圾收集商铺配电间储DT5商铺D439商铺D人 行 道架空空间160个车位商铺1. GENERAL CONTRACTOR SHALL VISIT THE SITE, REVIEW THE BUILDING SHELLDRAWINGS AS SUBMITTED

2、 BY THE LANDLORD OR STARBUCKS SITE SURVEYOR,AND BECOME THOROUGHLY FAMILIAR WITH THE SITE CONDITIONS PRIOR TOBIDDING OR CONSTRUCTION.2. GENERAL CONTRACTOR SHALL CONSULT WITH STARBUCKS CONSTRUCTIONMANAGER TO RESOLVE ANY CHANGES, OMISSIONS, OR PLAN DISCREPANCIESPRIOR TO BIDDING OR CONSTRUCTION.3. ALL W

3、ORK SHALL BE PERFORMED IN STRICT COMPLIANCE WITH LOCAL,COUNTY, STATE, AND FEDERAL CODES AND ORDINANCES.4. GENERAL CONTRACTOR SHALL VERIFY THE LOCATION OF ALL UTILITIES.5. GENERAL CONTRACTOR TO VERIFY ALL DIMENSIONS, INCLUDINGCLEARANCES REQUIRED BY OTHER TRADES, AND NOTIFY STARBUCKSCONSTRUCTION MANAG

4、ER OF ANY DISCREPANCIES PRIOR TO PROCEEDINGWITH THE WORK. ALL DIMENSIONS ARE TO THE FACE OF THE FINISHEDSURFACE UNLESS NOTED OTHERWISE. ALL DIMENSIONS TO BE TAKEN FROMDESIGNATED DATUM POINT. DO NOT SCALE DRAWINGS.6. GENERAL CONTRACTOR SHALL PATCH AND REPAIR ALL EXISTING WALLS,FLOORS, CEILINGS, OR OT

5、HER SURFACES IDENTIFIED TO REMAIN THAT MAYBECOME DAMAGED DURING THE COURSE OF THE WORK.7. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR OBTAINING PERMITS FORFIRE PROTECTION, PLUMBING, MECHANICAL, AND ELECTRICAL SYSTEMS PRIORTO INSTALLATION OF SUCH SYSTEMS.8. GENERAL CONTRACTOR SHALL RETAIN ONE SET OF TH

6、E PLANS TO NOTEAND DOCUMENT ALL CHANGES DURING CONSTRUCTION. THIS SET SHALL BEA PART OF THE GENERAL CONTRACTORS “STORE CLOSE-OUT PACKAGE” ASDESCRIBED IN THE CONSTRUCTION MANAGEMENT AGREEMENT.9. GENERAL CONTRACTOR IS RESPONSIBLE FOR COORDINATING DELIVERY OFMATERIALS FROM STARBUCKS CONTRACTED THIRD PA

7、RTY LOGISTICSDISTRIBUTION SERVICES AND VENDOR DIRECT SHIPMENTS. REFER TOCONSTRUCTION MANAGEMENT AGREEMENT FOR METHODS AND LEAD TIMES.10. RESPONSIBILITY FOR SUPPLY AND DELIVERY OF MATERIALS ANDEQUIPMENT IS IDENTIFIED IN THE DRAWING SCHEDULE SHEETS UNDER THECOLUMN LABELED RESPONSIBILITY.11. FOR THE PU

8、RPOSE OF THE DOCUMENTS, TO “INSTALL”, SHALL MEAN TOPROVIDE ALL FASTENERS, MISCELLANEOUS HARDWARE, BLOCKING,ELECTRICAL CONNECTIONS, PLUMBING CONNECTIONS, AND OTHER ITEMSREQUIRED FOR A COMPLETE AND OPERATION INSTALLATION, UNLESSOTHERWISE NOTED.12. ALL ITEM SUBSTITUTIONS MUST BE APPROVED BY THE STARBUC

9、KSDESIGN MANAGER.13. REFER TO ITEM CUTSHEETS FOR ADDITIONAL INFORMATION.GENERAL NOTESVICINITY PLANMAILINGADDRESS:DESIGNMANAGER:Starbucks Coffee Company2401 Utah Avenue SouthMS Stop: S-SD10Seattle, Washington 98134(206) 318-1575Vivi LeeStarbucks (China) Company Limited10th floor Innovation Builiding

10、1009Yishan RoadShanghai/200233 P.R.China86 21 2412 5916 Phone86 21 2412 3260 FaxPROJECT CONTACTSINDEX OF SHEETSROOM SCHEDULE上海汉思建筑设计事务所上海汉思建筑设计事务所HSarchitectsHSarchitectsPROJECT NAME:PROJECT ADDRESS:DESIGN DEVELOPMENT ONLY - NOT INTENDED FOR CONSTRUCTIONRC 2011 STARBUCKS COFFEE COMPANY2401 UTAH AVEN

11、UE SOUTHSEATTLE, WASHINGTON 98134(206) 318-1575STARBUCKS COFFEECOMPANYTHESE DRAWINGS AND SPECIFICATIONS ARECONFIDENTIAL AND SHALL REMAIN THE SOLEPROPERTY OF STARBUCKS CORPORATION,WHICH IS THE OWNER OF THE COPYRIGHT INTHIS WORK. THEY SHALL NOT BE REPRODUCED(IN WHOLE OR IN PART), SHARED WITH THIRDPART

12、IES OR USED IN ANY MANNER ON OTHERPROJECTS OR EXTENSIONS TO THIS PROJECTWITHOUT THE PRIOR WRITTEN CONSENT OFSTARBUCKS CORPORATION. THESE DRAWINGSAND SPECIFICATIONS ARE INTENDED TOEXPRESS DESIGN INTENT FOR APROTOTYPICAL STARBUCKS STORE (WHICH ISSUBJECT TO CHANGE AT ANYTIME) AND DO NOTREFLECT ACTUAL S

13、ITE CONDITIONS. NEITHERPARTY SHALL HAVE ANY OBLIGATION NORLIABILITY TO THE OTHER (EXCEPT STATEDABOVE) UNTIL A WRITTEN AGREEMENT IS FULLYEXECUTED BY BOTH PARTIES.SHEET NUMBER:SHEET TITLE:SCALE:STORE #:CONCEPT:PROJECT #:PALETTE:ISSUE DATE:DESIGN MANAGER:PRODUCTION DESIGNER:CHECKED BY:RLEED AP:当作作作2013

14、-2-1 13:37:39 N:当当当当当当_相相相相201206星星星2专专I室室201206-17 Guangzhou ZS Chigangbei store58436-001Revit58436-001chigangbei store.rteG-0001GENERALINFORMATION58436-0012013.01Guangzhou Chigangbei StoreNo.18 North Chigang road, Haizhu district, GZMCSHeritageVivi LeeEmma Zhuang / HSaEmma ZhuangNAMEAREABackbar18

15、mCafe Seating77 mOutdoor Seating69 mWash Room5 mWork Room14 m总总183 mSHEETSHEET TITLEGENERALG-0001GENERAL INFORMATIONG-0010DESIGN SPECIFICATIONSG-0011DESIGN SPECIFICATIONSG-0012DESIGN SPECIFICATIONSG-0013DESIGN SPECIFICATIONSARCHITECTURALA-0001ARCHITECTURAL INFORMATIONA-1001ARCHITECTURAL SITE PLANA-2

16、001EXTERIOR ELEVATIONSA-2002EXTERIOR ELEVATIONSINTERIORSI-1101DEMOLITION FLOOR PLANI-1103FLOOR PLANI-1105FF AND E PLANI-1106FF AND E SCHEDULESI-1107CASEWORK PLANI-1108REFLECTED CEILING PLANI-1109FLOOR FINISH PLANI-1111WALL FINISH PLANI-2101INTERIOR ELEVATIONSI-2102INTERIOR ELEVATIONSI-2103INTERIOR E

17、LEVATIONSI-2104INTERIOR ELEVATIONSI-2105INTERIOR ELEVATIONSI-5001DESIGN DETAILSI-50023D View 01I-50033D View 02I-6001SCHEDULESI-6002SCHEDULESPLUMBINGP-0001PLUMBING SPECIFICATIONSP-1101PLUMBING DESIGNP-5001PLUMBING DETAILSMECHANICALM-0001MECHANICAL SPECIFICATIONSELECTRICALE-0001ELECTRICAL SPECIFICATI

18、ONSE-1102ELECTRICAL DESIGNE-1103LIGHTING DESIGNE-5001ELECTRICAL DETAILSRevision ScheduleRevDateByDescriptionSECTION 017419 - CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL1.1SUMMARYA.SALVAGING NONHAZARDOUS DEMOLITION AND CONSTRUCTION WASTE.B.RECYCLING NONHAZARDOUS DEMOLITION AND CONSTRUCTION WASTE.C.DIS

19、POSING OF NONHAZARDOUS DEMOLITION AND CONSTRUCTION WASTE.1.2DEFINITIONSA.CONSTRUCTION WASTE: BUILDING AND SITE IMPROVEMENT MATERIALSAND OTHER SOLID WASTE RESULTING FROM CONSTRUCTION, REMODELING,RENOVATION, OR REPAIR OPERATIONS. CONSTRUCTION WASTE INCLUDESPACKAGING.B.DEMOLITION WASTE: BUILDING AND SI

20、TE IMPROVEMENT MATERIALSRESULTING FROM DEMOLITION OR SELECTIVE DEMOLITION OPERATIONS.C.DISPOSAL: REMOVAL OFF-SITE OF DEMOLITION AND CONSTRUCTIONWASTE AND SUBSEQUENT SALE, RECYCLING, REUSE, OR DEPOSIT INLANDFILL OR INCINERATOR ACCEPTABLE TO AUTHORITIES HAVINGJURISDICTION.D.RECYCLE: RECOVERY OF DEMOLI

21、TION OR CONSTRUCTION WASTE FORSUBSEQUENT PROCESSING IN PREPARATION FOR REUSE.E.SALVAGE: RECOVERY OF DEMOLITION OR CONSTRUCTION WASTE ANDSUBSEQUENT SALE OR REUSE IN ANOTHER FACILITY.F.SALVAGE AND REUSE: RECOVERY OF DEMOLITION OR CONSTRUCTIONWASTE AND SUBSEQUENT INCORPORATION INTO THE WORK.1.3PERFORMA

22、NCE REQUIREMENTSA.END-OF-PROJECT RATES FOR SALVAGE/RECYCLING: 50 75 PERCENT.1.4ACTION SUBMITTALSA.WASTE MANAGEMENT PLAN: SUBMIT PLAN WITHIN 7 DAYS OF DATEESTABLISHED FOR COMMENCEMENT OF THE WORK.1.TYPES AND QUANTITIES OF DEMOLITION AND CONSTRUCTIONWASTE.2.TYPE OF WASTE AND WHETHER IT WILL BE SALVAGE

23、D, RECYCLED,OR DISPOSED OF IN LANDFILL OR INCINERATOR.3.NET ADDITIONAL COST OR NET SAVINGS RESULTING FROM WASTEMANAGEMENT PLAN.1.5INFORMATION SUBMITTALSA.WASTE REDUCTION PROGRESS REPORTS: CONCURRENT WITH EACHAPPLICATION FOR PAYMENT, SUBMIT REPORT INDICATING TYPE OF WASTEAND WHETHER IT HAS BEEN SALVA

24、GED, RECYCLED, OR DISPOSED OF INLANDFILL OR INCINERATOR.B.WASTE DISPOSAL RECORDS: INDICATE RECEIPT AND ACCEPTANCE OFWASTE MATERIAL BY ACCEPTING AND PROCESSING FACILITIES LICENSEDTO ACCEPT THEM. INCLUDE MANIFESTS, TYPE OF MATERIAL, WEIGHT ORVOLUME TICKETS, RECEIPTS, AND INVOICES.C.LEED SUBMITTAL: CWM

25、 REPORTING TEMPLATE, TABULATING TOTALWASTE MATERIAL, QUANTITIES DIVERTED AND MEANS BY WHICH IT ISDIVERTED, AND STATEMENT THAT REQUIREMENTS FOR THE CREDIT HAVEBEEN MET.1.6RECYCLING WASTEA.RECYCLING INCENTIVES: REVENUES AND OTHER INCENTIVES FORRECYCLING WILL ACCRUE TO OWNER.END OF SECTION 017419SECTIO

26、N 018100 - SUSTAINABLE DESIGN REQUIREMENTS1.1SUMMARYA.THIS SECTION INCLUDES GENERAL REQUIREMENTS AND PROCEDURESFOR COMPLIANCE WITH CERTAIN U.S. GREEN BUILDING COUNCILS(USGBC) LEED PREREQUISITES AND CREDITS NEEDED FOR THE PROJECTTO OBTAIN LEED CERTIFICATION BASED ON LEED 2009 FOR RETAIL:COMMERCIAL IN

27、TERIORS LEED 2009 FOR RETAIL: NEW CONSTRUCTION.1.OTHER LEED PREREQUISITES AND CREDITS NEEDED TO OBTAIN LEED CERTIFICATION ARE DEPENDENT ON MATERIAL SELECTIONSAND MAY NOT BE SPECIFICALLY IDENTIFIED AS LEEDREQUIREMENTS. COMPLIANCE WITH REQUIREMENTS NEEDED TOOBTAIN LEED PREREQUISITES AND CREDITS MAY BE

28、 USED AS ONECRITERION TO EVALUATE SUBSTITUTION REQUESTS.2.ADDITIONAL LEED PREREQUISITES AND CREDITS NEEDED TOOBTAIN THE INDICATED LEED CERTIFICATION ARE DEPENDENT ONTHE ARCHITECTS DESIGN AND OTHER ASPECTS OF THE PROJECTTHAT ARE NOT PART OF THE WORK OF THE CONTRACT.1.2DEFINITIONSA.BASE BUILDING MATER

29、IAL: MATERIALS PERMANENTLY ATTACHED TO THESTRUCTURE. INCLUDES FINISHES AND PERMANENT CABINETS ANDCASEWORK.B.CHAIN-OF-CUSTODY CERTIFICATES: CERTIFICATES SIGNED BYMANUFACTURERS CERTIFYING THAT WOOD USED TO MAKE PRODUCTSWAS OBTAINED FROM FORESTS CERTIFIED BY AN FSC-ACCREDITEDCERTIFICATION BODY TO COMPL

30、Y WITH FSC STD-01-001, FSC PRINCIPLESAND CRITERIA FOR FOREST STEWARDSHIP. CERTIFICATES SHALLINCLUDE EVIDENCE THAT MANUFACTURER IS CERTIFIED FOR CHAIN OFCUSTODY BY AN FSC-ACCREDITED CERTIFICATION BODY.C.REGIONALLY MANUFACTURED MATERIALS: MATERIALS THAT AREMANUFACTURED WITHIN A RADIUS OF 500 MILES (80

31、0 KM) FROM PROJECTSITE. MANUFACTURING REFERS TO THE FINAL ASSEMBLY OFCOMPONENTS INTO THE BUILDING PRODUCT THAT IS INSTALLED ATPROJECT SITE.D.REGIONALLY EXTRACTED AND MANUFACTURED MATERIALS: REGIONALLYMANUFACTURED MATERIALS MADE FROM RAW MATERIALS THAT AREEXTRACTED, HARVESTED, OR RECOVERED WITHIN A R

32、ADIUS OF 500 MILES(800 KM) FROM PROJECT SITE.E.RECYCLED CONTENT: MATERIAL THAT HAS BEEN BROKEN DOWN ANDRECONSTITUTED INTO NEW MATERIAL. THE RECYCLED CONTENT VALUEOF A MATERIAL ASSEMBLY SHALL BE DETERMINED BY WEIGHT. THERECYCLED FRACTION OF THE ASSEMBLY IS THEN MULTIPLIED BY THECOST OF ASSEMBLY TO DE

33、TERMINE THE RECYCLED CONTENT VALUE.1.POST-CONSUMER MATERIAL IS DEFINED AS WASTE MATERIALGENERATED BY HOUSEHOLDS OR BY COMMERCIAL, INDUSTRIAL,AND INSTITUTIONAL FACILITIES IN THEIR ROLE AS END USERS OFTHE PRODUCT, WHICH CAN NO LONGER BE USED FOR ITSINTENDED PURPOSE.2.PRE-CONSUMER MATERIAL IS DEFINED A

34、S MATERIAL DIVERTEDFROM THE WASTE STREAM DURING THE MANUFACTURINGPROCESS. EXCLUDED IS REUTILIZATION OF MATERIALS SUCH ASREWORK, REGRIND, OR SCRAP GENERATED IN A PROCESS ANDCAPABLE OF BEING RECLAIMED WITHIN THE SAME PROCESS THATGENERATED IT.F.RESOURCE REUSE: MATERIAL THAT HAS BEEN KEPT INTACT ANDREPU

35、RPOSED TO A NEW USE ON THE SAME PROJECT SITE OR FOR THEORIGINAL OR NEW USE ON A DIFFERENT PROJECT SITE. FURNITURE MAYBE REPURPOSED FOR THE ORIGINAL USE ON THE SAME PROJECT SITE.1.3SUBMITTALSA.GENERAL: SUBMIT ADDITIONAL LEED SUBMITTALS REQUIRED BY OTHERSPECIFICATION SECTIONS.B.LEED DOCUMENTATION SUBM

36、ITTALS:1.CREDIT MR 2: COMPLY WITH SECTION 017419 CONSTRUCTIONWASTE MANAGEMENT AND DISPOSAL.2.CREDIT MR 3: RECEIPTS FOR SALVAGED AND REFURBISHEDMATERIALS USED FOR PROJECT, INDICATING SOURCES ANDCOSTS FOR SALVAGED AND REFURBISHED MATERIALS.3.CREDIT MR 4: PRODUCT DATA AND CERTIFICATION LETTER FROMPRODU

37、CT MANUFACTURERS INDICATING PERCENTAGES BYWEIGHT OF POST-CONSUMER AND PRE-CONSUMER RECYCLEDCONTENT FOR PRODUCTS HAVING RECYCLED CONTENT. INCLUDESTATEMENT INDICATING MATERIAL COSTS FOR EACH PRODUCTHAVING RECYCLED CONTENT.4.CREDIT MR 5: PRODUCT DATA INDICATING LOCATION OFMATERIAL MANUFACTURER FOR REGI

38、ONALLY MANUFACTUREDMATERIALS. INCLUDE STATEMENT INDICATING COST FOR EACHREGIONALLY MANUFACTURED MATERIAL AND FOR EACHIONALLY EXTRACTED AND MANUFACTURED MATERIAL.a.INCLUDE STATEMENT INDICATING DISTANCE FROMMANUFACTURER TO PROJECT FOR EACH REGIONALLYMANUFACTURED MATERIAL.b.INCLUDE STATEMENT INDICATING

39、 LOCATION OF ANDDISTANCE FROM PROJECT TO POINT OF EXTRACTION,HARVEST, OR RECOVERY FOR EACH RAW MATERIAL USEDIN REGIONALLY EXTRACTED AND MANUFACTUREDMATERIALS.5.CREDIT MR 7: PRODUCT DATA AND CHAIN-OF-CUSTODYCERTIFICATES FOR PRODUCTS CONTAINING CERTIFIED WOOD.INCLUDE STATEMENT INDICATING COST FOR EACH

40、 CERTIFIEDWOOD PRODUCT.6.CREDIT IEQ 3.1:a.CONSTRUCTION INDOOR-AIR-QUALITY MANAGEMENT PLAN.b.PRODUCT DATA FOR TEMPORARY FILTRATION MEDIA.c.PRODUCT DATA FOR FILTRATION MEDIA USED DURINGOCCUPANCY.d.CONSTRUCTION DOCUMENTATION: SIX PHOTOGRAPHS ATTHREE DIFFERENT TIMES DURING THE CONSTRUCTIONPERIOD, ALONG

41、WITH A BRIEF DESCRIPTION OF THESMACNA APPROACH EMPLOYED, DOCUMENTINGIMPLEMENTATION OF THE INDOOR-AIR-QUALITYMANAGEMENT MEASURES, SUCH AS PROTECTION OFDUCTS AND ON-SITE STORED OR INSTALLED ABSORPTIVEMATERIALS.7.CREDIT IEQ 3.2:a.SIGNED STATEMENT DESCRIBING THE BUILDING AIR FLUSH-OUT PROCEDURES INCLUDI

42、NG THE DATES WHEN FLUSH-OUT WAS BEGUN AND COMPLETED AND STATEMENT THATFILTRATION MEDIA WAS REPLACED AFTER FLUSH-OUT.b.PRODUCT DATA FOR FILTRATION MEDIA USED DURINGFLUSH-OUT AND DURING OCCUPANCY.8.CREDIT IEQ 4A: PRODUCT DATA FOR ADHESIVES AND SEALANTSUSED INSIDE THE WEATHERPROOFING SYSTEM INDICATING

43、VOCCONTENT OF EACH PRODUCT USED.9.CREDIT IEQ 4B: PRODUCT DATA FOR PAINTS AND COATINGS USEDINSIDE THE WEATHERPROOFING SYSTEM INDICATING VOC CONTENTOF EACH PRODUCT USED.10.CREDIT IEQ 4D: PRODUCT DATA FOR PRODUCTS CONTAININGCOMPOSITE WOOD OR AGRIFIBER PRODUCTS OR WOOD GLUESINDICATING THAT THEY DO NOT C

44、ONTAIN UREA-FORMALDEHYDERESIN.1.4INFORMATIONAL SUBMITTALSA.LEED ACTION PLANS: PROVIDE PRELIMINARY SUBMITTALS WITHIN SEVENDAYS OF DATE ESTABLISHED FOR COMMENCEMENT OF THE WORKINDICATING HOW THE FOLLOWING REQUIREMENTS WILL BE MET:1.CREDIT MR 2: WASTE MANAGEMENT PLAN COMPLYING WITHSECTION 017419 CONSTR

45、UCTION WASTE MANAGEMENT ANDDISPOSAL.2.CREDIT IEQ 3.1: CONSTRUCTION INDOOR-AIR-QUALITYMANAGEMENT PLAN.B.LEED PROGRESS REPORTS: CONCURRENT WITH EACH APPLICATION FORPAYMENT, SUBMIT REPORTS COMPARING ACTUAL CONSTRUCTION ANDPURCHASING ACTIVITIES WITH LEED ACTION PLANS FOR THE FOLLOWING:1.CREDIT MR 2: WAS

46、TE REDUCTION PROGRESS REPORTS COMPLYINGWITH SECTION 017419 CONSTRUCTION WASTE MANAGEMENT ANDDISPOSAL.END OF SECTION 018100GENERAL CONDITIONSSECTION 014200 - REFERENCESPART 1 - GENERAL1.1INDUSTRY STANDARDSA.APPLICABILITY OF STANDARDS: UNLESS THE CONTRACT DOCUMENTSINCLUDE MORE STRINGENT REQUIREMENTS,

47、APPLICABLE CONSTRUCTIONINDUSTRY STANDARDS HAVE THE SAME FORCE AND EFFECT AS IF BOUNDOR COPIED DIRECTLY INTO THE CONTRACT DOCUMENTS TO THE EXTENTREFERENCED. SUCH STANDARDS ARE MADE A PART OF THE CONTRACTDOCUMENTS BY REFERENCE.B.PUBLICATION DATES: COMPLY WITH STANDARDS IN EFFECT AS OF DATE OFTHE CONTR

48、ACT DOCUMENTS UNLESS OTHERWISE INDICATED.C.COPIES OF STANDARDS: EACH ENTITY ENGAGED IN CONSTRUCTION ONPROJECT SHOULD BE FAMILIAR WITH INDUSTRY STANDARDS APPLICABLE TOITS CONSTRUCTION ACTIVITY. COPIES OF APPLICABLE STANDARDS ARE NOTBOUND WITH THE CONTRACT DOCUMENTS.1.WHERE COPIES OF STANDARDS ARE NEE

49、DED TO PERFORM AREQUIRED CONSTRUCTION ACTIVITY, OBTAIN COPIES DIRECTLYFROM PUBLICATION SOURCE.1.2ABBREVIATIONS AND ACRONYMSA.INDUSTRY ORGANIZATIONS: WHERE ABBREVIATIONS AND ACRONYMS AREUSED IN SPECIFICATIONS OR OTHER CONTRACT DOCUMENTS, THEY SHALLMEAN THE RECOGNIZED NAME OF THE ENTITIES IN THE FOLLO

50、WING LIST.ACIAMERICAN CONCRETE INSTITUTEAHAAMERICAN HARDBOARD ASSOCIATIONAITCAMERICAN INSTITUTE OF TIMBER CONSTRUCTIONANSIAMERICAN NATIONAL STANDARDS INSTITUTEAPAAPA - THE ENGINEERED WOOD ASSOCIATIONASHRAEAMERICAN SOCIETY OF HEATING, REFRIGERATING ANDAIR-CONDITIONING ENGINEERSASTMASTM INTERNATIONAL(