2022年2022年光电耦合过零触发电路moc .pdf

《2022年2022年光电耦合过零触发电路moc .pdf》由会员分享，可在线阅读，更多相关《2022年2022年光电耦合过零触发电路moc .pdf（10页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、PACKAGESCHEMATIC4/9/04Page 1 of 10? 2003 Fairchild Semiconductor Corporation6-PIN DIP ZERO-CROSSPHOTOTRIAC DRIVER OPTOCOUPLER(600V PEAK)MOC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-MDESCRIPTIONThe MOC306X-M and MOC316X-M devices consist of a GaAs infrared emitting diode optically coupled to a monolit

2、hic silicon detector performing the function of a zero voltage crossing bilateral triac driver. They are designed for use with a triac in the inter-face of logic systems to equipment powered from 115/240 VAC lines, such as solid-state relays, industrial controls, motors, sole-noids and consumer appl

3、iances, etc.FEATURES?Simpli?es logic control of 115/240 VAC power?Zero voltage crossing?dv/dt of 1000 V/s guaranteed (MOC316X-M), 600 s guaranteed (MOC306X-M)?VDE recognized (File # 94766) ordering option V (e.g., MOC3063V-M)?Underwriters Laboratories (UL) recognized (File #E90700, volume 2)APPLICAT

4、IONS ?Solenoid/valve controls?Static power switches?Temperature controls?AC motor starters?Lighting controls?AC motor drives?E.M. contactors?Solid state relays616611MAIN TERM.NC*N/C*DO NOT CONNECT(TRIAC SUBSTRATE)123ANODECATHODE456MAIN TERM.ZEROCROSSINGCIRCUIT名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - -

5、 - - - - - - - - 名师精心整理 - - - - - - - 第 1 页，共 10 页 - - - - - - - - - 4/9/04Page 2 of 10? 2003 Fairchild Semiconductor Corporation6-PIN DIP ZERO-CROSSPHOTOTRIAC DRIVER OPTOCOUPLER(600V PEAK)MOC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-MABSOLUTE MAXIMUM RATINGS (TA = 25 C unless otherwise noted)Paramet

6、ersSymbolDeviceValueUnitsTOTAL DEVICEStorage T emperatureTSTGAll-40 to +150COperating T emperatureTOPRAll-40 to +85CLead Solder T emperatureTSOLAll260 for 10 secCJunction T emperature RangeTJAll-40 to +100CIsolation Surge Voltage(4) (peak AC voltage, 60Hz, 1 sec duration)VISOAll7500Vac(pk)Total Devi

7、ce Power Dissipation 25CPDAll250mWDerate above 25C2.94mW/ CEMITTERContinuous Forward CurrentIFAll60mAReverse VoltageVRAll6VTotal Power Dissipation 25C AmbientPDAll120mWDerate above 25C1.41mW/ CDETECTOROff-State Output T erminal VoltageVDRMAll600VPeak Repetitive Surge Current (PW = 100 s, 120 pps)ITS

8、MAll1ATotal Power Dissipation 25C AmbientPDAll150mWDerate above 25C1.76mW/ C名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 2 页，共 10 页 - - - - - - - - - 4/9/04Page 3 of 10? 2003 Fairchild Semiconductor Corporation6-PIN DIP ZERO-CROSSPHOTOTRIAC DRIVER OPTOCOUPLER(600V

9、PEAK)MOC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-M*Typical values at TA = 25 CNotes1. Test voltage must be applied within dv/dt rating.2. All devices are guaranteed to trigger at an IF value less than or equal to max IFT. Therefore, recommended operating IF lies between max IFT (15 mA for MOC3061-M,

10、 10 mA for MOC3062-M & MOC3162-M, 5 mA for MOC3063-M & MOC3163-M) and absolute max IF (60 mA).3. This is static dv/dt. See Figure 9 for test circuit. Commutating dv/dt is a function of the load-driving thyristor(s) only.4. Isolation surge voltage, VISO, is an internal device dielectric breakdown rat

11、ing. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common. ELECTRICAL CHARACTERISTICS (TA = 25 C Unless otherwise speci?ed)INDIVIDUAL COMPONENT CHARACTERISTICSParametersTest ConditionsSymbolDeviceMinTyp*MaxUnitsEMITTER Input Forward VoltageIF = 30 mAVFAll1.31.5VReverse Leakage Curr

12、entVR = 6 VIRAll0.005100ADETECTORPeak Blocking Current, Either DirectionVDRM = 600V, IF = 0 (note 1)IDRM1MOC316X-M10100nAMOC306X-M10500Critical Rate of Rise of Off-State VoltageIF = 0 (?gure 9, note 3)dv/dtMOC306X-M6001500V/ sMOC316X-M1000TRANSFER CHARACTERISTICS (TA = 25 C Unless otherwise speci?ed

13、.)DC CharacteristicsTest ConditionsSymbolDeviceMinTyp*MaxUnitsLED Trigger Current(rated IFT)main terminalVoltage = 3V (note 2)IFTMOC3061-M15mAMOC3062-M/MOC3162-M10MOC3063-M/MOC3163-M5Peak On-State Voltage, Either DirectionITM = 100 mA peak, IF = rated IFTVTMAll1.83VHolding Current, Either DirectionI

14、HAll500AZERO CROSSING CHARACTERISTICSCharacteristicsTest ConditionsSymbolDeviceMinTyp*MaxUnitsInhibit Voltage (MT1-MT2 voltageabove which device will not trigger)IF = Rated IFTVINHMOC3061-M/2M/3M1220VMOC3162-M/3M1215Leakage in Inhibited StateIF = Rated IFT,VDRM = 600V, off stateIDRM2All150500AISOLAT

15、ION CHARACTERISTICSCharacteristicsTest ConditionsSymbolDeviceMinTyp*MaxUnitsIsolation Voltagef = 60 Hz, t = 1 secVISOAll7500V名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 3 页，共 10 页 - - - - - - - - - 4/9/04Page 4 of 10? 2003 Fairchild Semiconductor Corporation6-PIN

16、DIP ZERO-CROSSPHOTOTRIAC DRIVER OPTOCOUPLER(600V PEAK)MOC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-MFigure 1. LED Forward Voltage vs. Forward CurrentFigure 3. LED Current Required to Trigger vs.LED Pulse WidthFigure 4. Leakage Current, IDRM vs. TemperatureFigure 2. Trigger Current Vs. TemperatureIF,

17、LED FORWARD CURRENT (mA)0.1110100VF,FORWARDVOLTAGE(V)0.70.80.91.01.11.21.31.41.51.61.7TA, AMBIENT TEMPERATURE ( C) -40-20020406080100TA, AMBIENT TEMPERATURE ( C) -40-20020406080100IFT,NORMALIZEDIDRM,LEAKAGECURRENT(nA)0.80.91.01.11.21.31.41.51.6PWIN, LED TRIGGER PULSE WIDTH ( s) 101100IFT,LEDTRIGGERC

18、URRENT(NORMALIZED)02468101214160.1110100100010000TA = -40 CVTM = 3VNORMALIZED TO TA = 25 CTA = 25 CNORMALIZED TO PWIN 100 sTA = 25 CTA = 85 C名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 4 页，共 10 页 - - - - - - - - - 4/9/04Page 5 of 10? 2003 Fairchild Semiconductor C

19、orporation6-PIN DIP ZERO-CROSSPHOTOTRIAC DRIVER OPTOCOUPLER(600V PEAK)MOC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-MFigure 5. IDRM2, Leakage in Inhibit State vs. TemperatureFigure 7. IH, Holding Current vs. TemperatureFigure 8. Inhibit Voltage vs. TemperatureFigure 6. On-State CharacteristicsVTM, ON-

20、STATE VOLTAGE (VOLTS) TA, AMBIENT TEMPERATURE ( C) -40-20020406080100TA, AMBIENT TEMPERATURE ( C) -40-20020406080100TA, AMBIENT TEMPERATURE ( C) -40-20020406080100IDRM2,NORMALIZEDVINH,NORMALIZEDIH,HOLDINGCURRENT(NORMALIZED)0.40.60.81.01.21.41.61.82.02.22.4IF = RATED IFTNORMALIZED TO TA = 25 C-4-3-2-

21、101234ITM,ON-STATECURRENT(mA)TA = 25 C-800-600-400-20002004006008000.00.40.81.21.62.02.42.83.20.800.850.900.951.001.051.101.151.20NORMALIZED TO TA = 25 C名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 5 页，共 10 页 - - - - - - - - - 4/9/04Page 6 of 10? 2003 Fairchild Sem

22、iconductor Corporation6-PIN DIP ZERO-CROSSPHOTOTRIAC DRIVER OPTOCOUPLER(600V PEAK)MOC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-M1. 100 x scope probes are used, to allow high speeds and voltages.2. The worst-case condition for static dv/dt is established by triggering the D.U.T. with a normal LED inpu

23、t current, then removing the current. The variable vernier resistor combined with various capacitor combinations allows the dv/dt to be gradually increased until the D.U.T. continues to trigger in response to the applied voltage pulse, even after the LED current has been removed. The dv/dt is then d

24、ecreased until the D.U.T. stops triggering. RC is measured at this point and recorded.BASIC APPLICATIONSTypical circuit for use when hot line switching is required. In this circuit the hot side of the line is switched and the load connected to the cold or neutral side. The load may be connected to e

25、ither the neutral or hot line.Rin is calculated so that IF is equal to the rated IFT of the part, 15 mA for the MOC3061-M, 10 mA for the MOC3062-M, or 5 mA for the MOC3063-M. The 39 ohm resistor and 0.01 F capacitor are for snubbing of the triac and is often, but not always, necessary depending upon

26、 the particular triac and load used.Suggested method of ?ring two, back-to-back SCRs with a Fairchild triac driver. Diodes can be 1N4001; resistors, R1 and R2, are optional 330 ohm.Note: This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.272W2W1

27、002WdVdtVERNIERMOUNT DUT ONTEMPERATURE CONTROLLEDC PLATEDIFFERENTIALPREAMPf = 10 HzPW = 100 s50 ? PULSEGENERATORALL COMPONENTS ARE NON-INDUCTIVE UNLESS SHOWN822W470pF0.0010.0050.010.0470.470.1562W1N91420V10001/4W1N967A18VRFP4N100DUT20kX100 PROBEX100 PROBEVDRM/VRRM SELECT6412100010 WATTWIREWOUND0.331

28、000VPOWER1 MEG2W EACH1.2 MEG2WTEST0-1000V10mA0.0471000VFigure 9. Circuit for Static dV Measurement of Power ThyristorsdtFigure 10. Hot-Line Switching Application Circuit0.01 FVCCRin123654240 VACHOTNEUTRAL360 ?360MOC3061-MMOC3062-MMOC3063-M39?FKPF12N60LOADFigure 11. Inverse-Parallel SCR Driver Circui

29、tVCCRin123654115 VACSCR360 ?R1D1SCRMOC3061-MMOC3062-MMOC3063-MR2D2LOAD名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 6 页，共 10 页 - - - - - - - - - 4/9/04Page 7 of 10? 2003 Fairchild Semiconductor Corporation6-PIN DIP ZERO-CROSSPHOTOTRIAC DRIVER OPTOCOUPLER(600V PEAK)M

30、OC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-MNOTEAll dimensions are in inches (millimeters)Package Dimensions (Through Hole)Package Dimensions (Surface Mount)Package Dimensions (0.4” Lead Spacing)Recommended Pad Layout forSurface Mount Leadform0.350 (8.89)0.320 (8.13)0.260 (6.60)0.240 (6.10)0.320 (8.

31、13)0.070 (1.77)0.040 (1.02)0.014 (0.36)0.010 (0.25)0.200 (5.08)0.115 (2.93)0.100 (2.54)0.015 (0.38)0.020 (0.50)0.016 (0.41)0.100 (2.54)150.012 (0.30)0.350 (8.89)0.320 (8.13)0.260 (6.60)0.240 (6.10)0.390 (9.90)0.332 (8.43)0.070 (1.77)0.040 (1.02)0.014 (0.36)0.010 (0.25)0.320 (8.13)0.035 (0.88)0.006 (

32、0.16)0.012 (0.30)0.008 (0.20)0.200 (5.08)0.115 (2.93)0.025 (0.63)0.020 (0.51)0.020 (0.50)0.016 (0.41)0.100 2.540.350 (8.89)0.320 (8.13)0.260 (6.60)0.240 (6.10)0.070 (1.77)0.040 (1.02)0.014 (0.36)0.010 (0.25)0.200 (5.08)0.115 (2.93)0.020 (0.50)0.016 (0.41)0.100 2.540.100 (2.54)0.015 (0.38)0.012 (0.30

33、)0.008 (0.21)0.425 (10.80)0.400 (10.16)0.070 (1.78)0.060 (1.52)0.030 (0.76)0.100 (2.54)0.305 (7.75)0.425 (10.79)名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 7 页，共 10 页 - - - - - - - - - 4/9/04Page 8 of 10? 2003 Fairchild Semiconductor Corporation6-PIN DIP ZERO-CROS

34、SPHOTOTRIAC DRIVER OPTOCOUPLER(600V PEAK)MOC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-MORDERING INFORMATIONMARKING INFORMATIONOptionOrder Entry Identi?erDescriptionSSSurface Mount Lead BendSR2 SR2Surface Mount; T ape and reelTT0.4 Lead SpacingVVVDE 0884TVTVVDE 0884, 0.4 Lead SpacingSVSVVDE 0884, Surf

35、ace MountSR2VSR2VVDE 0884, Surface Mount, Tape & ReelMOC3061V X YY Q126435*Note Parts that do not have the V option (see de?nition 3 above) that are marked with date code 325 or earlier are marked in portrait format.De?nitions1Fairchild logo2Device number3VDE mark (Note: Only appears on parts ordere

36、d with VDE option See order entry table)4One digit year code, e.g., 35Two digit work week ranging from 01 to 536Assembly package code名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 8 页，共 10 页 - - - - - - - - - 4/9/04Page 9 of 10? 2003 Fairchild Semiconductor Corporati

37、on6-PIN DIP ZERO-CROSSPHOTOTRIAC DRIVER OPTOCOUPLER(600V PEAK)MOC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-MNOTEAll dimensions are in inches (millimeters)Re?ow Pro?le (White Package, -M Suf?x)Carrier Tape Specifications4.0 0.1?1.5 MINUser Direction of Feed2.0 0.051.75 0.1011.5 1.024.0 0.312.0 0.10.30

38、 0.0521.0 0.14.5 0.200.1 MAX10.1 0.209.1 0.20?1.5 0.1/-0Ramp up = 210 C/sec ? Peak reflow temperature: 245 C (package surface temperature) ? Time of temperature higher than 183 C for 120 180 seconds ? One time soldering reflow is recommended 230 C, 10 30 sTime (Minute)03002502001501005000.511.522.53

39、3.544.5Temperature(C)Time above 183 C, 120 180 sec245 C peak名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 9 页，共 10 页 - - - - - - - - - LIFE SUPPORT POLICY FAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOU

40、T THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein:1.Life support devices or systems are devices or systemswhich, (a) are intended for surgical implant into the body, or(b) support or sustain life, and (c) whose failure to performwhen properly used

41、 in accordance with instructions for useprovided in the labeling, can be reasonably expected toresult in a significant injury of the user.2.A critical component in any component of a life supportdevice or system whose failure to perform can bereasonably expected to cause the failure of the life supp

42、ortdevice or system, or to affect its safety or effectiveness.DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE

43、OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.4/9/04Page 10 of 10? 2003 Fairchild Semiconductor Corporation6-PIN DIP ZERO-CROSSPHOTOTRIAC DRIVER OPTOCOUPLER(600V PEAK)MOC3061-MMOC3062-MMOC3063-MMOC3162-MMOC3163-M名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 10 页，共 10 页 - - - - - - - - -