ZG标准之法兰及其连接件PN法兰用垫圈的尺寸第部分钢法兰用缠绕式垫片中国一重机械.pdf

《ZG标准之法兰及其连接件PN法兰用垫圈的尺寸第部分钢法兰用缠绕式垫片中国一重机械.pdf》由会员分享，可在线阅读，更多相关《ZG标准之法兰及其连接件PN法兰用垫圈的尺寸第部分钢法兰用缠绕式垫片中国一重机械.pdf（15页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、Licensed Copy: FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy, (c) BSIBritish StandardA single copy of this British Standard is licensed toFELIX HERZING10 March 2004This is an uncontrolled copy. Ensure use of the mostcurrent version of this document by sear

2、ching BritishStandards Online at bsonline.techindex.co.uk|BRITISH STANDARDBS EN1514-2 : 1997The European Standard EN 1514-2 : 1997 has the status of aBritish StandardICS 23.040.80NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWFlanges and their joints Dimensions of gaskets forP

3、N-designated flangesPart 2. Spiral wound gaskets for use withsteel flangesLicensed Copy: FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy, (c) BSIBS EN 1514-2 : 1997This British Standard, havingbeen prepared under thedirection of the Sector Board forEngineeri

4、ng, was published underthe authority of the StandardsBoard and comes into effect on15 August 1997 BSI 1997The following BSI referencesrelate to the work on thisstandard:Committee reference PSE/2Draft for comment 94/709820 DCISBN 0 580 27685 6Amendments issued since publicationAmd. No.DateText affect

5、edCommittees responsible for thisBritish StandardThe preparation of this British Standard was entrusted to Technical CommitteePSE/2, Jointing materials and compounds, upon which the following bodies wererepresented:Asbestos Information Centre Ltd.British Adhesives and Sealants AssociationBritish Com

6、pressed Gases AssociationBritish Hydromechanics Research GroupChartered Institution of Water and Environmental ManagementEnergy Industries CouncilIndustrial Water SocietyL P Gas AssociationWater Services Association of England and WalesLicensed Copy: FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5

7、954918, 10 March 2004, Uncontrolled Copy, (c) BSIBS EN 1514-2 : 1997 BSI 1997iContentsPageCommittees responsibleInside front coverNational forewordiiForeword2Text of EN 1514-23Licensed Copy: FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy, (c) BSIw w w . b z

8、 f x w . c o mii BSI 1997BS EN 1514-2 : 1997National forewordThis Part of BS EN 1514 has been prepared by Technical Committee PSE/2, and is theEnglish language version of EN 1514-2 : 1997 Flanges and their joints Dimensionsof gaskets for PN-designated flanges Part 2: Spiral wound gaskets for use wit

9、h steelflanges, published by the European Committee for Standardization (CEN).This Part of BS EN 1514 supersedes BS 4865 : Part 2 : 1989, which is withdrawn.Cross-referencesPublication referred toCorresponding British StandardEN ISO 6708 : 1995BS EN ISO 6708 : 1996 Pipework components Definitionand

10、selection of DN (nominal size)Compliance with a British Standard does not of itself confer immunityfrom legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, pages i and ii, the ENtitle page, pages 2 to 8, an inside back cover and a back cover.Licensed Copy:

11、 FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy, (c) BSIw w w . b z f x w . c o mCENEuropean Committee for StandardizationComite Europe en de NormalisationEuropa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels 1997 All ri

12、ghts of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 1514-2 : 1997 EEUROPEAN STANDARDEN 1514-2NORME EUROPEENNEEUROPAISCHE NORMApril 1997ICS 23.040.80Descriptors: Industrial piping, flange connections, pipe joints, spiral wound gaskets, pipe flange

13、s, steels, dimensions, markingEnglish versionFlanges and their joints Dimensions of gaskets for PN-designatedflanges Part2: Spiral wound gaskets for use with steel flangesBrides et leurs assemblages Dimensions desjoints pour les brides de signe s PN Partie 2:Joints spirale s pour utilisation avec de

14、s brides enacierFlansche und ihre Verbindungen Mae fu rDichtungen fu r Flansche mit PN-Bezeichnung Teil 2: Spiraldichtungen fu r StahlflanscheThis European Standard was approved by CEN on 1997-01-09. CEN members arebound to comply with the CEN/CENELEC Internal Regulations which stipulate theconditio

15、ns for giving this European Standard the status of a national standardwithout any alteration.Up-to-date lists and bibliographical references concerning such national standardsmay be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three officia

16、l versions (English, French, German).A version in any other language made by translation under the responsibility of aCEN member into its own language and notified to the Central Secretariat has thesame status as the official versions.CEN members are the national standards bodies of Austria, Belgium

17、, Denmark,Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands,Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Licensed Copy: FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy, (c) BSIw w w . b z f x w . c o mPage

18、2EN 1514-2 : 1997 BSI 1997ForewordThis European Standard has been prepared byTechnical Committee CEN/TC 74, Flanges and theirjoints, the secretariat of which is held by DIN.This European Standard shall be given the status of anational standard, either by publication of an identicaltext or by endorse

19、ment, at the latest by October 1997,and conflicting national standards shall be withdrawnat the latest by October 1997.Annex A is informative and contains information to besupplied by the purchaser.Annex B is informative and contains A-deviations.EN 1514 consists of four Parts:Part 1:Specification f

20、or non-metallic flat gasketswith or without insertsPart 2:Specification for spiral wound gasketsfor use with steel flangesPart 3:Specification for non-metallic PTFEenvelope gasketsPart 4:Specification for corrugated, flat orgrooved metallic and filled metallicgaskets for use with steel flangesAccord

21、ing to the CEN/CENELEC Internal Regulations,the national standards organizations of the followingcountries are bound to implement this EuropeanStandard: Austria, Belgium, Denmark, Finland, France,Germany, Greece, Iceland, Ireland, Italy, Luxembourg,Netherlands, Norway, Portugal, Spain, Sweden,Switze

22、rland and the United Kingdom.ContentsPageForeword2Introduction31Scope32Normative references33Definitions43.1DN43.2PN44Designations44.1Range of PN designations44.2Range of DN (nominal sizes)44.3Gasket types44.4Information to be supplied by thepurchaser45Gasket designs46Gasket types57Dimensions58Marki

23、ng6AnnexesA(informative) Information to besupplied by the purchaser7B(informative) A-deviation7Licensed Copy: FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy, (c) BSIw w w . b z f x w . c o mPage 3EN 1514-2 : 1997 BSI 1997IntroductionThe dimensions of spiral

24、 wound gaskets for tongueand groove flanges and spigot and recess flanges toEN 1092-1 are not included in this standard. Suchgaskets may be available, however, for these types offlanges and the purchaser is advised to consult themanufacturer as to their availability.WARNING. Gaskets made to this sta

25、ndard maycontain asbestos. Materials containing asbestos may besubject to legislation that requires precautions to betaken when handling them to ensure that they do notconstitute a hazard to health (see annex B). Attentionis drawn to relevant EEC directives.1 ScopeThis European Standard specifies th

26、e dimensions andmarking of spiral wound gaskets for use in conjunctionwith flat face and raised face flanges complying withprEN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63 andPN 100 and up to and including DN 900.NOTE 1. Dimensions of other types of gaskets for use withflanges to prEN 1092-1, prEN

27、1092-2, prEN 1092-3 andprEN 1092-4 are given in EN 1514-1, EN 1514-3 and EN 1514-4.NOTE 2. Annex A lists information that should be supplied by thepurchaser when ordering gaskets.2 Normative referencesThis European Standard incorporates by dated orundated reference, provisions from other publication

28、s.These normative references are cited at theappropriate places in the text and the publications arelisted hereafter. For dated references, subsequentamendments to or revisions of any of thesepublications apply to this European Standard onlywhen incorporated in it by amendment or revision. Forundate

29、d references the latest edition of the publicationreferred to applies.prEN 1092-1Flanges and their joints Circularflanges for pipes, valves and fittings Part 1: Steel flanges PNdesignatedprEN 1092-2Flanges and their joints Part 2:Cast iron flangesprEN 1092-3Flanges and their joints Circularflanges f

30、or pipes, valves, fittings andaccessories Part 3: Copper alloyand composite flanges PNdesignatedprEN 1092-4Flanges and their joints Circularflanges for pipes, valves, fittings andaccessories PN designated Part 4: Aluminium alloy flangesEN 1333Pipework components Definitionand selection of PNEN ISO 6

31、708Pipework components Definitionand selection of DN (nominal size)(ISO 6708 : 1995)Licensed Copy: FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy, (c) BSIw w w . b z f x w . c o mPage 4EN 1514-2 : 1997 BSI 19973 DefinitionsFor the purposes of this standard,

32、 the followingdefinitions apply.3.1 DNSee EN ISO 6708.3.2 PNSee EN 1333.4 Designations4.1 Range of PN designationsGaskets shall be designated as suitable for use withone or more of the following PN designations offlange:PN 10PN 40PN 16PN 63PN 25PN 1004.2 Range of DN (nominal sizes)Gasket nominal siz

33、es shall be designated in accordancewith the ranges specified in table 1.4.3 Gasket typesGasket types, as defined in clause 6 and as illustratedin figure 1, shall be designated as: type C/I: sealing element with centring ring andinner ring; type C/O: sealing element with centring ring.4.4 Informatio

34、n to be supplied by the purchaserNOTE. For information to be supplied by the purchaser,see annex A.5 Gasket designsGaskets for which dimensions are specified shall be ofone of the designs shown in figure 1.The clearance between the sealing element and thecentring ring shall be such that the sealing

35、elementcannot fall out of the ring during normal handling.NOTE 1. Figure 2 shows a typical design of a metallic spiralwound gasket for use with type A or type B flanges.NOTE 2. Type A and type B flange facings are illustrated inprEN 1092-1.NOTE 3. The profile of the metal winding of the sealing elem

36、ent isat the option of the manufacturer.NOTE 4. The materials of the gasket are chosen by themanufacturer to suit the operating conditions. Therefore, thepurchaser should define the operating conditions in the enquiryand/or order (see annex A).WARNING. Gaskets made to this standard maycontain asbest

37、os. Materials containing asbestos may besubject to legislation that requires precautions to betaken when handling them to ensure that they do notconstitute a hazard to health (see annex B). Attentionis drawn to relevant EEC directives.NOTE 5. The attention of the user is drawn to the load necessaryt

38、o compress spiral wound gaskets and the available load withPN 10 and PN 16 flanges should be verified as adequate prior tousing these gaskets.a) Type C/Ib) Type C/OFigure 1. Spiral wound gasketsLicensed Copy: FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy,

39、(c) BSIw w w . b z f x w . c o mPage 5EN 1514-2 : 1997 BSI 1997Dimensions in millimetresFigure 2. Dimensions of typical metallic spiral wound gaskets6 Gasket typesGaskets shall be one of the following types:a) type C/I sealing element with centring ring andinner ring;b) type C/O sealing element with

40、 centring ring.All gaskets shall have a centring ring. All PN 63 andPN 100 gaskets shall have an inner ring. All gasketscontaining PTFE filler material shall have an inner ring.NOTE 1. The use of an inner ring is recommended for all PNdesignations and the purchaser should specify on his enquiryand/o

41、r order if an inner ring is required for PN 10, PN 16,PN 25 and PN 40 gaskets (see annex A).NOTE 2. The selection of gasket type should take into account thefluids, the operating conditions, the properties of the gasketmaterials, the type and surface finish of the flange facing and theflange bolt lo

42、ading. It is recommended that selection of gasketsfor any particular application is made in consultation with thegasket supplier (see annex A).7 DimensionsThe dimensions of spiral wound gaskets for types Aand B flange facings shall be as given in table 1, andoverall thickness, including filler, shal

43、l be as given infigure 2.Licensed Copy: FELIX HERZING, TUV RHEINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy, (c) BSIPage 6EN 1514-2 : 1997 BSI 1997Table 1. Dimensions of spiral wound gaskets for type A and type B flange facingsDimensions in millimetresDNInnerringinsidediameterm

44、in.2)Sealingelementinsidediametermin.Sealing elementoutside diametermax.Centring ring outside diameter1)PN 10 toPN 40PN 63 andPN 100PN 10PN 16PN 25PN 40PN 63PN 100101523,636,436,4484848485858151927,640,440,4535353536363202433,647,448,4636363637474253040,655,456,4737373738484323949,666,467,4848484849

45、090404555,672,474,494949494105105505667,686,488,4109109109109115121657283,6103,4106,4129129129129140146808496,6117,4120,4144144144144150156100108122,6144,4148,4164164170170176183125133147,6170,4174,4194194196196213220150160176,6200,4205,4220220226226250260200209228,6255,4263,427527528629331232725026

46、2282,4310,4319,4330331343355367394300311331,6360,4369,4380386403420427461350355374,6405,4413,4440446460477489515400406425,6458,4466,4491498517549546575450452476,6512,4541558567574500508527,6566,4572,4596620627631660708600610634,6675,4683,4698737734750768819700710734,0778,5786,58138078368839568008118

47、35,0879,5887,5920914945994900909933,0980,5990,510201014104511141)The tolerances for the dimensions of the centring ring outside diameter of spiral wound gaskets aremm up to and including2 0,80DN 600 andmm above DN 600.21,502)If the purchaser requires a specific dimension for the inner ring inside di

48、ameter then this requirement shall be stated on the enquiryand/or order (see annex A).8 MarkingThe centring ring shall be marked with the followinginformation: the manufacturers name or trade mark; DN followed by the appropriate number; the PN designation; the manufacturers symbols for the materials

49、 of themetal winding, the filler material and (whereapplicable) the inner ring.EXAMPLE. AAA/BBB, DN 300, PN 25, XXXGaskets shall be identified either individually or on thepackaging containing the gasket(s) with the number ofthis European Standard, i.e. EN 1514-2.Licensed Copy: FELIX HERZING, TUV RH

50、EINLAND BERLIN BRANDENBURG 5954918, 10 March 2004, Uncontrolled Copy, (c) BSIPage 7EN 1514-2 : 1997 BSI 1997Annex A (informative)Information to be supplied by thepurchaserBefore ordering a gasket it is recommended that theselection of the gasket type should be made inconsultation with the gasket sup