H3C MSR系列路由器IPsec典型配置举例(V7)(25页).doc

《H3C MSR系列路由器IPsec典型配置举例(V7)(25页).doc》由会员分享，可在线阅读，更多相关《H3C MSR系列路由器IPsec典型配置举例(V7)(25页).doc（25页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、-H3C MSR系列路由器IPsec典型配置举例(V7)-第 25 页1简介2配置前提3使用iNode客户端基于证书认证的L2TP over IPsec功能配置举例3.1组网需求3.2配置思路3.3使用版本3.4配置步骤3.4.1 Device的配置3.4.2 Host的配置3.5验证配置3.6配置文件4 IPsec over GRE的典型配置举例4.1组网需求4.2配置思路4.3使用版本4.4配置步骤4.4.1 Device A的配置4.4.2 Device B的配置4.5验证配置4.6配置文件5 GRE over IPsec的典型配置举例5.1组网需求5.2配置思路5.3使用版本5.4配置

2、步骤5.4.1 Device A的配置5.4.2 Device B的配置5.5验证配置5.6配置文件6 IPsec同流双隧道的典型配置举例6.1组网需求6.2使用版本6.3配置步骤6.3.1 Device A的配置6.3.2 Device B的配置6.4验证配置6.5配置文件7相关资料1简介本文档介绍IPsec的典型配置举例。2配置前提本文档适用于使用Comware V7软件版本的MSR系列路由器，如果使用过程中与产品实际情况有差异，请参考相关产品手册，或以设备实际情况为准。本文档中的配置均是在实验室环境下进行的配置和验证，配置前设备的所有参数均采用出厂时的缺省配置。如果您已经对设备进行了配置

3、，为了保证配置效果，请确认现有配置和以下举例中的配置不冲突。本文档假设您已了解IPsec特性。3使用iNode客户端基于证书认证的L2TP over IPsec功能配置举例3.1组网需求如图1所示，PPP用户Host与Device建立L2TP隧道，Windows server 2003作为CA服务器，要求：通过L2TP隧道访问Corporate network。用IPsec对L2TP隧道进行数据加密。采用RSA证书认证方式建立IPsec隧道。图1基于证书认证的L2TP over IPsec配置组网图3.2配置思路由于使用证书认证方式建立IPsec隧道，所以需要在ike profile中配置lo

4、cal-identity为dn，指定从本端证书中的主题字段取得本端身份。3.3使用版本本举例是在R0106版本上进行配置和验证的。3.4配置步骤3.4.1Device的配置(1)配置各接口IP地址#配置接口GigabitEthernet2/0/1的IP地址。 system-viewDevice interface gigabitethernet 2/0/1Device-GigabitEthernet2/0/1 ip address 192.168.100.50 24Device-GigabitEthernet2/0/1 quit#配置接口GigabitEthernet2/0/2的IP地址。De

5、vice interface gigabitethernet 2/0/2Device-GigabitEthernet2/0/2 ip address 102.168.1.11 24Device-GigabitEthernet2/0/2 quit#配置接口GigabitEthernet2/0/3的IP地址。Device interface gigabitethernet 2/0/3Device-GigabitEthernet2/0/3 ip address 192.168.1.1 24Device-GigabitEthernet2/0/3 quit(2)配置L2TP#创建本地PPP用户l2tpu

6、ser，设置密码为hello。Device local-user l2tpuser class networkDevice-luser-network-l2tpuser password simple helloDevice-luser-network-l2tpuser service-type pppDevice-luser-network-l2tpuser quit#配置ISP域system对PPP用户采用本地验证。Device domain systemDevice-isp-system authentication ppp localDevice-isp-system quit#启用L

7、2TP服务。Device l2tp enable#创建接口Virtual-Template0，配置接口的IP地址为172.16.0.1/24。Device interface virtual-template 0Device-Virtual-Template0 ip address 172.16.0.1 255.255.255.0#配置PPP认证方式为PAP。Device-Virtual-Template0 ppp authentication-mode pap#配置为PPP用户分配的IP地址为172.16.0.2。Device-Virtual-Template0 remote address

8、 172.16.0.2Device-Virtual-Template0 quit#创建LNS模式的L2TP组1。Device l2tp-group 1 mode lns#配置LNS侧本端名称为lns。Device-l2tp1 tunnel name lns#关闭L2TP隧道验证功能。Device-l2tp1 undo tunnel authentication#指定接收呼叫的虚拟模板接口为VT0。Device-l2tp1 allow l2tp virtual-template 0Device-l2tp1 quit(3)配置PKI证书#配置PKI实体security。Device pki ent

9、ity securityDevice-pki-entity-security common-name deviceDevice-pki-entity-security quit#新建PKI域。Device pki domain headgateDevice-pki-domain-headgate ca identifier LYQDevice-pki-domain-headgate certificate request url http:/192.168.1.51/certsrv/mscep/mscep.dllDevice-pki-domain-headgate certificate re

10、quest from raDevice-pki-domain-headgate certificate request entity securityDevice-pki-domain-headgate undo crl check enableDevice-pki-domain-headgatepublic-key rsa general name abc length 1024Device-pki-domain-headgate quit#生成RSA算法的本地密钥对。Device public-key local create rsa name abcThe range of public

11、 key modulus is (512 2048).If the key modulus is greater than 512,it will take a few minutes.Press CTRL+C to abort.Input the modulus length default = 1024:Generating Keys.Create the key pair successfully.#获取CA证书并下载至本地。Device pki retrieve-certificate domain headgate caThe trusted CAs finger print is:

12、 MD5 fingerprint:8649 7A4B EAD5 42CF 5031 4C99 BFS3 2A99 SHA1 fingerprint:61A9 6034 181E 6502 12FA 5A5F BA12 0EA0 5187 031CIs the finger print correct?(Y/N):yRetrieved the certificates successfully.#手工申请本地证书。Device pki request-certificate domain headgateStart to request general certificate .Certific

13、ate requested successfully.(4)配置IPsec隧道#创建IKE安全提议。Device ike proposal 1Device-ike-proposal-1 authentication-method rsa-signatureDevice-ike-proposal-1 encryption-algorithm 3des-cbcDevice-ike-proposal-1 dh group2Device-ike-proposal-1 quit#配置IPsec安全提议。Device ipsec transform-set tran1Device-ipsec-transf

14、orm-set-tran1 esp authentication-algorithm sha1Device-ipsec-transform-set-tran1 esp encryption-algorithm 3desDevice-ipsec-transform-set-tran1 quit#配置IKE profile。Device ike profile profile1Device-ike-profile-profile1 local-identity dnDevice-ike-profile-profile1 certificate domain headgateDevice-ike-p

15、rofile-profile1 proposal 1Device-ike-profile-profile1 match remote certificate deviceDevice-ike-profile-profile1 quit#在采用数字签名认证时，指定总从本端证书中的主题字段取得本端身份。Deviceike signature-identity from-certificate#创建一条IPsec安全策略模板，名称为template1，序列号为1。Deviceipsec policy-template template1 1Device-ipsec-policy-template-t

16、emplate1-1 transform-set tran1Device-ipsec-policy-template-template1-1 ike-profile profile1Device-ipsec-policy-template-template1-1 quit#引用IPsec安全策略模板创建一条IPsec安全策略，名称为policy1，顺序号为1。Device ipsec policy policy1 1 isakmp template template1#在接口上应用IPsec安全策略。Device interface gigabitethernet 2/0/2Device-Gi

17、gabitEthernet2/0/2 ipsec apply policy policy1Device-GigabitEthernet2/0/2 quit3.4.2Host的配置(1)从证书服务器上申请客户端证书#登录到证书服务器：http:/192.168.1.51/certsrv，点击“申请一个证书”。图1进入申请证书页面#点击“高级证书申请”。图2高级证书申请#选择第一项：创建并向此CA提交一个申请。图3创建并向CA提交一个申请#填写相关信息。需要的证书类型，选择“客户端身份验证证书”；密钥选项的配置，勾选“标记密钥为可导出”前的复选框。#点击，弹出一提示框：在对话框中选择“是”。#点击

18、安装此证书。图4安装证书(2)iNode客户端的配置（使用iNode版本为：iNode PC 5.2(E0409)）#打开L2TP VPN连接，并单击“属性(Y)”。图5打开L2TP连接#输入LNS服务器的地址，并启用IPsec安全协议，验证证方法选择证书认证。图6基本配置#单击按钮，进入“L2TP设置”页签，设置L2TP参数如下图所示。图7L2TP设置#单击“IPsec设置”页签，配置IPsec参数。图8IPsec参数设置#单击“IKE设置”页签，配置IKE参数。图9IKE参数设置#单击“路由设置”页签，添加访问Corporate network的路由。图10路由设置#完成上述配置后，单击按

19、钮，回到L2TP连接页面。3.5验证配置#在L2TP连接对话框中，输入用户名“l2tpuser”和密码“hello”，单击按钮。图11连接L2TP#在弹出的对话框中选择申请好的证书，单击按钮。图12证书选择#通过下图可以看到L2TP连接成功。图13连接成功图14连接成功#在Device上使用display ike sa命令，可以看到IPsec隧道第一阶段的SA正常建立。 display ike sa Connection-ID Remote Flag DOI 10 102.168.1.1 RD IPSECFlags:RD-READY RL-REPLACED FD-FADING#在Device上

20、使用display ipsec sa命令可以看到IPsec SA的建立情况。 display ipsec saInterface: GigabitEthernet2/0/2 IPsec policy: policy1 Sequence number: 1 Mode: template Tunnel id: 0 Encapsulation mode: tunnel Perfect forward secrecy: Path MTU: 1443 Tunnel: local address: 102.168.1.11 remote address: 102.168.1.1 Flow: sour ad

21、dr: 102.168.1.11/255.255.255.255 port: 1701 protocol: udp dest addr: 102.168.1.1/255.255.255.255 port: 0 protocol: udp Inbound ESP SAs SPI: 2187699078 (0x8265a386) Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-SHA1 SA duration (kilobytes/sec): 1843200/3600 SA remaining duration (kilobytes/sec): 18431

22、97/3294 Max received sequence-number: 51 Anti-replay check enable: Y Anti-replay window size: 64 UDP encapsulation used for NAT traversal: N Status: Active Outbound ESP SAs SPI: 3433374591 (0xcca5237f) Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-SHA1 SA duration (kilobytes/sec): 1843200/3600 SA rem

23、aining duration (kilobytes/sec): 1843197/3294 Max sent sequence-number: 52 UDP encapsulation used for NAT traversal: N Status: Active3.6配置文件interface Virtual-Template0ppp authentication-mode papremote address 172.16.0.2ip address 172.16.0.1 255.255.255.0interface GigabitEthernet2/0/1ip address 192.1

24、68.100.50 255.255.255.0interface GigabitEthernet2/0/2ip address 102.168.1.11 255.255.255.0ipsec apply policy policy1interface GigabitEthernet2/0/3ip address 192.168.1.1 255.255.255.0domain systemauthentication ppp locallocal-user l2tpuser class networkpassword cipher $c$3$nl46fURLtkCkcbdnB6irTXma+E6

25、u0c+hservice-type pppauthorization-attribute user-role network-operatorpki domain headgateca identifier LYQcertificate request url http:/192.168.1.51/certsrv/mscep/mscep.dllcertificate request from racertificate request entity securitypublic-key rsa general name abcundo crl check enablepki entity se

26、curitycommon-name hostipsec transform-set tran1esp encryption-algorithm 3des-cbcesp authentication-algorithm sha1ipsec policy-template template1 1transform-set tran1ike-profile profile1ipsec policy policy1 1 isakmp template template1l2tp-group 1 mode lnsallow l2tp virtual-template 0undo tunnel authe

27、nticationtunnel name lnsl2tp enableike signature-identity from-certificateike profile profile1certificate domain headgatelocal-identity dnmatch remote certificate deviceproposal 1ike proposal 1authentication-method rsa-signatureencryption-algorithm 3des-cbcdh group24IPsec over GRE的典型配置举例4.1组网需求如图15所

28、示，企业远程办公网络通过IPsec VPN接入企业总部，要求：通过GRE隧道传输两网络之间的IPsec加密数据。图15IPsec over GRE组网图4.2配置思路为了对数据先进行IPsec处理，再进行GRE封装，访问控制列表需匹配数据的原始范围，并且要将IPsec应用到GRE隧道接口上。为了对网络间传输的数据先进行IPsec封装，再进行GRE封装，需要配置IPsec隧道的对端IP地址为GRE隧道的接口地址。4.3使用版本本举例是在R0106版本上进行配置和验证的。4.4配置步骤4.4.1Device A的配置(1)配置各接口IP地址#配置接口GigabitEthernet2/0/1的IP地

29、址。 system-viewDeviceA interface gigabitethernet 2/0/1DeviceA-GigabitEthernet2/0/1 ip address 192.168.1.1 255.255.255.0DeviceA-GigabitEthernet2/0/1 tcp mss 1350DeviceA-GigabitEthernet2/0/1 quit#配置接口GigabitEthernet2/0/2的IP地址。DeviceA interface gigabitethernet 2/0/2DeviceA-GigabitEthernet2/0/2 ip addres

30、s 202.115.22.48 255.255.255.0DeviceA-GigabitEthernet2/0/2 quit(2)配置GRE隧道#创建Tunnel0接口，并指定隧道模式为GRE over IPv4隧道。DeviceA interface tunnel 0 mode gre#配置Tunnel0接口的IP地址为10.1.1.1/24。DeviceA-Tunnel0 ip address 10.1.1.1 255.255.255.0#配置Tunnel0接口的源端地址为202.115.22.48/24（Device A的GigabitEthernet2/0/2的IP地址）。Device

31、A-Tunnel0 source 202.115.22.48#配置Tunnel0接口的目的端地址为202.115.24.50/24（Device B的GigabitEthernet2/0/2的IP地址）。DeviceA-Tunnel0 destination 202.115.24.50DeviceA-Tunnel0 quit#配置从Device A经过Tunnel0接口到Remote office network的静态路由。DeviceA ip route-static 192.168.2.1 255.255.255.0 tunnel 0(3)配置IPsec VPN#配置IKE keychai

32、n。DeviceA ike keychain keychain1DeviceA-ike-keychain-keychain1 pre-shared-key address 10.1.1.2 255.255.255.0 key simple 123DeviceA-ike-keychain-keychain1 quit#创建ACL3000，定义需要IPsec保护的数据流。DeviceA acl number 3000DeviceA-acl-adv-3000 rule 0 permit ip source 192.168.1.0 0.0.0.255 destination 192.168.2.0 0

33、.0.0.255DeviceA-acl-adv-3000 quit#配置IPsec安全提议。DeviceA ipsec transform-set tran1DeviceA-ipsec-transform-set-tran1 esp encryption-algorithm desDeviceA-ipsec-transform-set-tran1 esp authentication-algorithm sha1DeviceA-ipsec-transform-set-tran1 quit#创建一条IKE协商方式的IPsec安全策略，名称为policy1，序列号为1。DeviceA ipsec

34、policy policy1 1 isakmpDeviceA-ipsec-policy-isakmp-policy1-1 security acl 3000DeviceA-ipsec-policy-isakmp-policy1-1 remote-address 10.1.1.2DeviceA-ipsec-policy-isakmp-policy1-1 transform-set tran1DeviceA-ipsec-policy-isakmp-policy1-1 quit#在GRE隧道接口上应用安全策略。DeviceA interface tunnel 0DeviceA-Tunnel0 ips

35、ec apply policy policy1DeviceA-Tunnel0 quit4.4.2Device B的配置(1)配置各接口IP地址#配置接口GigabitEthernet2/0/1的IP地址。 system-viewDeviceB interface gigabitethernet 2/0/1DeviceB-GigabitEthernet2/0/1 ip address 192.168.2.1 255.255.255.0DeviceB-GigabitEthernet2/0/1 tcp mss 1350DeviceB-GigabitEthernet2/0/1 quit#配置接口Gig

36、abitEthernet2/0/2的IP地址。DeviceB interface gigabitethernet 2/0/2DeviceB-GigabitEthernet2/0/2 ip address 202.115.24.50 255.255.255.0DeviceB-GigabitEthernet2/0/2 quit(2)配置GRE隧道#创建Tunnel0接口，并指定隧道模式为GRE over IPv4隧道。DeviceB interface tunnel 0 mode gre#配置Tunnel0接口的IP地址为10.1.1.2/24。DeviceB-Tunnel0 ip address

37、 10.1.1.2 255.255.255.0#配置Tunnel0接口的源端地址为202.115.24.50/24（Device B的GigabitEthernet2/0/2的IP地址）。DeviceB-Tunnel0 source 202.115.24.50#配置Tunnel0接口的目的端地址为202.115.22.48/24（Device A的GigabitEthernet2/0/2的IP地址）。DeviceB-Tunnel0 destination 202.115.22.48DeviceB-Tunnel0 quit#配置从DeviceB经过Tunnel0接口到Corporate netw

38、ork的静态路由。DeviceB ip route-static 192.168.1.1 255.255.255.0 tunnel 0(3)配置IPsec VPN#配置IKE keychain。DeviceB ike keychain keychain1DeviceB-ike-keychain-keychain1 pre-shared-key address 10.1.1.1 255.255.255.0 key simple 123DeviceB-ike-keychain-keychain1 quit#创建ACL3000，定义需要IPsec保护的数据流。DeviceB acl number 3

39、000DeviceB-acl-adv-3000 rule 0 permit ip source 192.168.2.0 0.0.0.255 destination 192.168.1.0 0.0.0.255DeviceB-acl-adv-3000 quit#配置IPsec安全提议。DeviceB ipsec transform-set tran1DeviceB-ipsec-transform-set-tran1 esp encryption-algorithm desDeviceB-ipsec-transform-set-tran1 esp authentication-algorithm s

40、ha1DeviceB-ipsec-transform-set-tran1 quit#创建一条IKE协商方式的IPsec安全策略，名称为policy1，序列号为1。DeviceB ipsec policy policy1 1 isakmpDeviceB-ipsec-policy-isakmp-policy1-1 security acl 3000DeviceB-ipsec-policy-isakmp-policy1-1 remote-address 10.1.1.1DeviceB-ipsec-policy-isakmp-policy1-1 transform-set tran1DeviceB-i

41、psec-policy-isakmp-policy1-1 quit#在GRE隧道接口上应用安全策略。DeviceB interface tunnel 0DeviceB-Tunnel0 ipsec apply policy policy1DeviceB-Tunnel0 quit4.5验证配置#以Corporate network的主机192.168.1.2向Remote office network的主机192.168.2.2发起通信为例，从192.168.1.2 ping 192.168.2.2，会触发IPsec协商，建立IPsec隧道，在成功建立IPsec隧道后，可以ping通。C:User

42、scorporatenetwork ping 192.168.2.2Pinging 192.168.2.2 with 32 bytes of data:Request timed out.Reply from 192.168.2.2: bytes=32 time=2ms TTL=254Reply from 192.168.2.2: bytes=32 time=2ms TTL=254Reply from 192.168.2.2: bytes=32 time=1ms TTL=254Ping statistics for 192.168.2.2: Packets: Sent = 4, Receive

43、d = 3, Lost = 1 (25% loss),Approximate round trip times in milli-seconds:Minimum = 1ms, Maximum = 2ms, Average = 1ms#在Device A上使用display ike sa命令，可以看到第一阶段的SA正常建立。 display ike sa Connection-ID Remote Flag DOI 1 10.1.1.2 RD IPSECFlags:RD-READY RL-REPLACED FD-FADING#在Device A上使用display ipsec sa命令可以看到IPsec SA的建立情况。 display ipsec saInterface: Tunnel0 IPsec policy: policy1 Sequence number: 1 Mode: isakmp Tunnel id: 0 Encapsulation mode: tunnel Perfect forward secrecy: Path MTU: 1419 Tunnel: local address: 10.1.1.1