制造业英语词汇(19页).doc

《制造业英语词汇(19页).doc》由会员分享，可在线阅读，更多相关《制造业英语词汇(19页).doc（19页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、-制造业英语词汇-第 19 页组装、冲压、喷漆等专业词汇 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fuse together熔合 fuse machine热熔机 supervisor 课长 cosmetic inspect外观检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front pla

2、te前板 rear plate后板 chassis 基座 bezel panel面板 Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 SOP制造作业程序 trolley台车 sub-line支线 left fork叉车 personnel resource department 人力资源部 planning department企划部 stamping factory冲压厂 uncoiler and straightener整平机 punching machine 冲床 robot机械手 h

3、ydraulic machine油压机 lathe车床 planer |plein|刨床 miller铣床 grinder磨床 driller?床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line sup

4、ervisor线长 be put in storage入库 to apply oil擦油 to file burr 锉毛刺 to connect material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to load material上料 to unload material卸料 to return material/stock to退料 scraped |skræpid|报废 scrape .v.刮;削 deficient purchase来料不良 manufacture procedu

5、re制程 deficient manufacturing procedure制程不良 oxidation | ksidein|氧化 dents压痕 defective upsiding down抽芽不良 defective to staking铆合不良 embedded lump镶块 feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 fork

6、lift叉车 trailer=long vehicle拖板车 compound die合模 die locker锁模器 pressure plate=plate pinch压板 bolt螺栓 administration/general affairs dept总务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 ped

7、al踩踏板 stopper阻挡器 flow board流水板 hydraulic handjack油压板车 forklift叉车 glove(s)手套 glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴 iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper扫把 mop拖把 vaccum cleaner吸尘器 rag 抹布 garbag

8、e container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条 jack升降机 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格 dimension/si

9、ze is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 sc

10、ratch划伤 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots水渍 polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交货期 cost成本 engineering工程 die repair模修 enterprise pla

11、n = enterprise expansion projects企划 die worker模工 to start a press开机 stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养 qualified products, up-to-grade products良品 defective products, not up-to-grade products不良品 waste废料 board看板 feeder送料机 sliding rack滑料架 defect

12、ive product box不良品箱 die change 换模 to fix a die装模 to take apart a die拆模 to repair a die修模 basket蝴蝶竺 plastic basket胶筐 isolating plate baffle plate; barricade隔板 to pull and stretch拉深 to put material in place, to cut material, to input落料 to impose lines压线 to compress, compressing压缩 character die字模 to fe

13、ed, feeding送料 (be)qualfied, up to grade合格 not up to grade, not qualified不合格 material change, stock change材料变更 feature change 特性变更 prepare for, make preparations for 准备 parameters参数 rotating speed, revolution转速 abnormal handling异常处理 lots of production生产批量 steel plate钢板 roll material卷料 to revise, modi

14、fy修订 to switch over to, switch-to throw-over switching over切换 engineering, project difficulty工程瓶颈 stage die工程模 automation自动化 to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模 shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for stamping 冲压常词汇 sta

15、mping, press冲压 punch press, dieing out press冲床 uncoiler & strainghtener整平机 feeder送料机 rack, shelf, stack料架 cylinder油缸 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset复位

16、filings铁削 to draw holes抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取 approval examine and verify审核 processing, to process加工 to return delivenry to. to send delinery back to retrn of goods退货 registration登记 registration card登记卡 to put forward and hand in提报 safe stock安全库存 acceptance

17、= receive验收 application form for purchase请购单 consume, consumption消耗 abrasion磨损 reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics统计 demand and supply需求 career card履历卡 to take apart a die卸下模具 to load a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓 to mo

18、ve away a die plate移走模板 easily damaged parts易损件 breaking.(be)broken,(be)cracked 断裂 to lubricate润滑 common vocabulary for die engineering模具工程常用词汇 die 模具 figure file, chart file图档 cutting die, blanking die冲裁模 progressive die, follow (-on)die 连续模 compound die复合模 punched hole冲孔 panel board镶块 to cutedges=

19、side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸 Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower

20、 die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 bolt螺栓 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 work in progress product在制品 casing = containerazation装箱 quantity of physical invetory second

21、 count 复盘点数量 quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department

22、together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用状况明细表 blank and waste sheet NO. 空白与作废单号 plate电镀 material for engineering mold testing工程试模材料 not included in phys

23、ical inventory不列入盘点 incoming material to be inspected进货待验 description品名 steel/rolled steel钢材 material statistics sheet 物料统计明细表 meeting type 会别 distribution department分发单位 present members出席人员 decision items决议事项 responsible department负责单位 pre-fixed finishing date预定完成日 approved by / checked by / prepar

24、ed by核准/审核/承办 PCE assembly production schedule sheet PCE组装厂生产排配表 model机锺 work order工令 revision版次 production control confirmation生产确认 checked by初审 approved by核准 stock age analysis sheet 库存货龄分析表 on-hand inventory现有库存 available material良品可使用 obsolete material良品已呆滞 to be inspected or reworked 待验或重工 tota

25、l合计 cause description原因说明 part number/ P/N 料号 item/group/class类别 prepared by制表 year-end physical inventory difference analysis sheet 年终盘点差异分析表 physical inventory盘点数量 physical count quantity帐面数量 difference quantity差异量 cause analysis原因分析 semi-finished product半成品 defective product/non-good parts不良品 dis

26、posed goods处理品 warehouse/hub仓库 on way location在途仓 oversea location海外仓 spare parts physical inventory list备品盘点清单 spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割 EDM放电机 coil stock卷料 sheet stock片料 score=groove压线 cam block滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差 pocket for the punch

27、head挂钩槽 slug hole废料孔 feature die公母模 expansion dwg展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割 set screw止付螺丝 form block折刀 stop pin定位销 round pierce punch=die button圆冲子 shape punch=die insert异形子 stock locater block定位块 under cut=scrap chopper清角 active plate活动板 baffle plate挡块 cover plate盖板 male die公模 f

28、emale die母模 groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套 club car高尔夫球车 capability能力 factor系数 phosphate皮膜化成 viscosity涂料粘度 alkalidipping脱脂 main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁 high-speed transmission高速传递 heat dissipation热传 r

29、ack上料 degrease脱脂 rinse水洗 alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔 scraped products报放心品 defective products不良品 disposed products处理品 stamping冲压 spare parts=buffer备品 coordinate座标 dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶 sand bl

30、asting喷沙 grit 砂砾 derusting machine除锈机 degate打浇口 dryer烘干机 induction感应 induction light感应光 response=reaction=interaction感应 ram连杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕疵shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利

31、granule=peuet=grain细粒 grit maker抽粒机 cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 mill锉 plane刨 grind磨 drill钻boring镗 blister气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄 crank shaft曲柄轴 augular offset角度偏差 velocity速度 production tempo生产进度现状 torque扭矩 spline=the mul

32、tiple keys花键 quenching淬火 tempering回火 annealing退火 carbonization碳化 alloy合金 tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性 resistance电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机 模具工程类 plain die简易模 pierce die冲孔模 forming die成型模 progre

33、ssive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce冲孔 forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点 dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面

34、压印 tick-mark farside反面压印 冲压名称类 extension dwg展开图 procedure dwg工程图 die structure dwg模具结构图 press specification冲床规格 die height range适用模高 die height闭模高度 punch wt.上模重量 五金零件类 inner guiding post内导柱 inner hexagon screw内六角螺钉 dowel pin固定销 coil spring弹簧 lifter pin顶料销 eq-height sleeves=spool等高套筒 pin销 lifter guid

35、e pin浮升导料销 guide pin导正销 wire spring圆线弹簧 outer guiding post外导柱 stop screw止付螺丝 outer bush外导套 模板类 top plate上托板（顶板） top block上垫脚 punch set上模座 punch pad上垫板 punch holder上夹板 stripper pad脱料背板 up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板 lower plate下模板 die pad下垫板 die holder下夹

36、板 die set下模座 bottom block下垫脚 bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板 inner stripper内脱料板 lower stripper下脱料板 零件类 punch冲头 insert入块(嵌入件) deburring punch压毛边冲子 groove punch压线冲子 stamped punch字模冲子 round punch圆冲子 special shape punch异形冲子 bending block折刀 roller滚轴 baffle plate挡块 located b

37、lock定位块 supporting block for location 定位支承块 air cushion plate气垫板 air-cushion eject-rod气垫顶杆 trimming punch切边冲子 stiffening rib punch = stinger 加强筋冲子 ribbon punch压筋冲子 reel-stretch punch卷圆压平冲子 guide plate定位板 sliding block滑块 sliding dowel block滑块固定块 active plate活动板 lower sliding plate下滑块板 upper holder bl

38、ock上压块 upper mid plate上中间板 spring box弹簧箱 spring-box eject-rod弹簧箱顶杆 spring-box eject-plate弹簧箱顶板 bushing bolck衬套 cover plate盖板 guide pad导料块 塑件&模具相关英文 compre sion molding压缩成型 flash mold溢流式模具 plsitive mold挤压式模具 split mold分割式模具 cavity型控 母模 core模心 公模 taper锥拔 leather cloak仿皮革 shiver饰纹 flow mark流痕 welding m

39、ark溶合痕 post screw insert螺纹套筒埋值 self tapping screw自攻螺丝 striper plate脱料板 piston活塞 cylinder汽缸套 chip细碎物 handle mold手持式模具 移转成型用模具 encapsulation molding低压封装成型 射出成型用模具 two plate两极式（模具） well type蓄料井 insulated runner绝缘浇道方式 hot runner热浇道 runner plat浇道模块 valve gate阀门浇口 band heater环带状的电热器 spindle阀针 spear head刨尖

40、头 slag well冷料井 cold slag冷料渣 air vent排气道 h=0.020.05mm w=3.2mm L=35mm welding line熔合痕 eject pin顶出针 knock pin顶出销 return pin回位销反顶针 sleave套筒 stripper plate脱料板 insert core放置入子 runner stripper plate浇道脱料板 guide pin导销 eject rod (bar)（成型机）顶业捧 subzero深冷处理 three plate三极式模具 runner system浇道系统 stress crack应力电裂 ori

41、entation定向 sprue gate射料浇口，直浇口 nozzle射嘴 sprue lock pin料头钩销(拉料杆) slag well冷料井 side gate侧浇口 edge gate侧缘浇口 tab gate搭接浇口 film gate薄膜浇口 flash gate闸门浇口 slit gate缝隙浇口 fan gate扇形浇口 dish gate因盘形浇口 H=F=1/2t1/5t T=2.53.5mm diaphragm gate隔膜浇口 ring gate环形浇口 subarine gate潜入式浇口 tunnel gate隧道式浇口 pin gate针点浇口 0.81.0m

42、m Runner less无浇道 (sprue less)无射料管方式 long nozzle延长喷嘴方式 sprue浇口;溶渣 品质人员名称类 QC quality control 品质管理人员 FQC final quality control 终点品质管制人员 IPQC in process quality control 制程中的品质管制人员 OQC output quality control 最终出货品质管制人员 IQC incoming quality control 进料品质管制人员 TQC total quality control 全面质量管理 POC passage qu

43、ality control 段检人员 QA quality assurance 质量保证人员 OQA output quality assurance 出货质量保证人员 QE quality engineering 品质工程人员 品质保证类 FAI first article inspection 新品首件检查 FAA first article assurance 首件确认 TVR tool verification report 模具确认报告 3B 3B 模具正式投产前确认 CP capability index 能力指数 CPK capability index of process 模

44、具制程能力参数 SSQA standardized supplier quality 合格供应商品质评估 OOBA out of box audit 开箱检查 QFD quality function deployment 品质机能展开 FMEA failure model effectiveness analysis 失效模式分析 8 disciplines 8项回复内容 FA final audit 最後一次稽核 CAR corrective action request 改正行动要求 corrective action report 改正行动报告 FQC运作类 AQL Acceptable Quality Level 运作类允收品质水准 S/S Sample size 抽样检验样本大小 ACC Accept 允收 REE Reject 拒收 CR Critical 极严重的 MAJ Major 主要的 MIN Minor 轻微的 AOQ Average Output Quality 平均出厂品质 AOQL Av