中英文翻译(9页).doc

《中英文翻译(9页).doc》由会员分享，可在线阅读，更多相关《中英文翻译(9页).doc（9页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、-中英文翻译-第 9 页Fuzzy Logic Based Autonomous Skid Steering Vehicle Navigation L.Doitsidis,K.P.Valavanis,N.C.Tsourveloudis Technical University of Crete Department of Production Engineering and Management Chania,Crete,Greece GR-73100 Idoitsidis ,kimonv,nikostdpem.tuc.grAbstract-A two-layer fuzzy logic co

2、ntroller has been designed for 2-D autonomous Navigation of a skid steering vehicle in an obstacle filled environment. The first layer of the Fuzzy controller provides a model for multiple sonar sensor input fusion and it is composed of four individual controllers, each calculating a collision possi

3、bility in front, back, left and right directions of movement. The second layer consists of the main controller that performs real-time collision avoidance while calculating the updated course to be applicability and implementation is demonstrated through experimental results and case studies perform

4、ed o a real mobile robot.Keywords - Skid steering, mobile robots, fuzzy navigation. .INTRODUCTION The exist several proposed solutions to the problem of autonomous mobile robot navigation in 2-D uncertain environments that are based on fuzzy logic1,2,evolutionary algorithms 3,as well as methods comb

5、ining fuzzy logic with genetic algorithms4 and fuzzy logic with electrostatic potential fields5. The paper is the outgrowth of recently published results 9,10,but it studies 2-D environments navigation and collision avoidance of a skid steering vehicle. Skid steering vehicles are compact, light, req

6、uire few parts to assemble and exhibit agility from point turning to line driving using only the motions, components, and swept volume needed for straight line driving. Skid steering vehicle motion differs from explicit steering vehicle motion in the way the skid steering vehicle turns. The wheels r

7、otation is limited around one axis and the back of steering wheel results in navigation determined by the speed change in either side of the skid steering vehicle. Same speed in either side results in a straight-line motion. Explicit steering vehicles turn differently since the wheels are moving aro

8、und two axes. The geometric configuration of a skid steering vehicle in the X-Y plane is shown in Fig1，while at is the heading angle, W is the robot width, the sense of rotation and S1, S2 are the speeds in the either side of the robot. The derived and implemented planner a two-layer fuzzy logic bas

9、ed controller that provides purely” reactive behavior” of the vehicle moving in a 2-D obstacle filled environment, with inputs readings from a ring of 24 sonar sensors and angle errors, and outputs the updated rotational and translational velocities of the vehicle.DESIGN OF THE FUZZY LOGIC CONTROL S

10、YSTEM The order to the vehicle movement, a two-layer Madman-type controller has been designed and implemented. In the first layer, there are four fuzzy logic controllers repondible for obstacle detection and calculation of the collision possibleilities in the four main directions, front, back, left

11、and right. The possibilities calculated in the first layer are the input to the second layer along with the angle error (the difference between the robot heading angle and the desired target angle), and the output is the updated vehicles translational and the rotational speed. Fig. 1.Geometric confi

12、guration of the robot in the X-Y plane.A .first layer of the fuzzy logic controller The ATRV-mini is equipped with an array of 24 ultrasonic sensors that are vehicles as shown in Fig.2. The ultrasonic sensors that are used are manufactured by Polaroid.After experiment with, and testing several metho

13、ds concerning sonar sensor date grouping and management, it was first decided to follow the sensor grouping in pairs as proposed in 8(considering the ATRV mini twelve sonar group Ais=1,.,12, have been enumerated as shown in Fig.2) and then divide the sun of the provided pair sensor data by two to de

14、termine the distance from the (potential) obstacle. However, this method gave unsatisfactory results due to the ATRV minis specific sensor unreliability. Even in cases with obstacles present in the vicinity of the vehicle, the sensors were detecting a “free path”. To overcome this problem, a modifie

15、d, simpler, sensor grouping and data management method was tested that return much better and accurate results: The sensors were again grouped in pairs according to Fig.2, but the minimum of the (potential) obstacle. Each ATRV mini sonar returns from obstacles at a maximum distance of 4metres (exper

16、imentally verified as opposed to different value provided by the sonar sensors manufacturerFig.2. Grouping of the Sensors.The form of each first layer individual fuzzy controller, including the obstacle detection module, is shown in Fig.3.Observing Fig.3, data from group sensors A1, A2, .,A5(5 input

17、s) and group sensors A7, A8 , ,A11(5 inputs) serve as inputs to the individual controllers responsible for the calculation of the front and back collision possibilities, respectively. Data from group sensors A5, A6, A7 (3 inputs) serve as input to calculate the left and right possibilities, respecti

18、vely. The individual fuzzy controllers utilize the same membership functions to calculate the collision possibilities. The linguistic values of the variable distance_from_obstance are defined to be three, near, meium_distance, away with membership functions as shown in Fig.4 reflecting the maximum d

19、istance of 4 meters a sonar returns accurate information about potential obstacles.Fig.3.Obstacle detection module.Fig.4.Input Variable Distance_ From _ Obstacle.The first layer output is a collision possibility in each direction taking values from 0 to 1.The linguistic variables describing each dir

20、ection output variable collision possibility (with empiricallyDerived for best performance) membership functions as shown In Fig.5.A part of the rules base for left collision is presented in Table. An example of the rules used to extract front collision possibilities is: IF A1 is near AND A2 is near

21、 AND A3 is Near AND A4 is medium_distance AND A5is near THEN collision_possibility is high. Similar for the back collision possibility.For left (equivalently for right collision)possibilities the rule is of the form: If A5 is near And A6 is nearAnd A7 is near THEN collision_possibility is high.Fig.5

22、.Output Variable collision_possibilityTABLE PART OF THE RULES BASE FOR LEFT COLLISIONInput VariablesOutputVariablesA5A6A7NearNearNearHigh_PossibilityAwayAwayAwayNot_possibleNearAwayMedium_DistancePossibleNearAwayNearHigh_PossibilityB. Second layer of the fuzzy logic controller The second layer fuzzy

23、 controller recives as inputs the four collision possibilities in the four directions and the angle error, and outputs the translational velocity, which is responsible for moving the vehicle backward or forward and the rotational speed, which is responsible for the vehicle rotation as shown in Fig.6

24、. The angle error represents the difference between the robot-heading angle and the desired angle the robot should have in order to reach its target. The angle error takes values ranging from-1800to 1800. The linguistic variables that represent the angle error are: Backwards_1, Hard_Left, Left, righ

25、t, Hard_right, Backwards_2 with (empirically derived from tests) membership functions as shown in Fig.7. The translational velocity (m/sec) , which is one of the outputs of the second layer controller, is described with the following linguistic variables: back_full, back, back_solw, stop, front_slow

26、, front, frontfull, with membership functions as in Fig.8.Fig 6.Block diagram of the 2nd layer of the fuzzy logic controllerFig 7.Input Variable Angle Error.Fig 8.Output Variable Translational_Velocity. The rotational_speed (rad/sc) is described with the following linguistic variables: Right_full, r

27、ight, no_ratation, left, let_full with membership functions as in Fig.9. An example of the rules that control the vehicle is demonstrated: If front_collision is Not_Possible AND Back_Collision is Not_possible And Left_Collision is Not_possible And Right_Collision is Not_possible And Angle Error is A

28、head THEN Translational_velocity is Front_Full AND Rotational_Velocity is No_Ratation.Fig. 9. Output Variable Rotational_velocity. RUSULTS The fuzzy logic controller has been designed and implemented using C+ in an ATRV-mini manufactured by Real World Interface(RWI). In all experiments the robot is

29、considered to have reached its target when stopping inside a circle with radius of 30 cm. This assumption has been dictated because all calculations have been made relative to the center of the robot. So if the robot stops inside that circle it is assumed that it has reached its target. Several scen

30、arios in an indoor 2-D obstacle filled environment have been tested to study the robot behavior and the controllers applicability. The arrow in Fig.10, Fig.15, Fig.20 is showing the initial direction of the vehicle. In test case 1 we examine the behavior of the vehicle in an environment with three o

31、bstacles. The test case 1 is presented in Fig.10. Fig.11 shows the translational velocity, while the rotational velocity is given in Fig.12.Fig.13 presents the front collision possibility. In Fig.14, the solid line indicates the left collision possibility while the doted the right collision possibil

32、ity. The behavior of the vehicle is defined from the surrounding obstacles. In the beginning the left collision possibility is high due to the obstacle in the left. The robot moves forwards and its steering right in order to avoid the obstacle. Then it steers left and moves towards its target. In th

33、e second test case presented in Fig.15, a more complicated environment with three obstacles has been tested. Fig.16 shows the translational velocity, while the rotational velocity is given in Fig.17. Fig.18 presents the front collision possibility while in Fig.19 the solid line indicates the left co

34、llision possibility while the doted the right collision possibility. In Fig.15 we can see that the path in front of the robot is blocked. The robot uses only the rotational velocity in order to steer and avoid the obstacle. Then it moves in a curve towards its target. The third test case considers a

35、n environment with many small obstacles. The path the vehicle is following is presented in Fig.20. Due to the obstacles that are around the vehicle, the vehicle is forced to make a small right turn an then it escapes from the closed area. Fig.21 shows the translational velocity, while the rotational

36、 velocity is given in Fig.22.Fig.23 presents the front collision possibility while in Fig.24 the solid line indicates the left collision possibility while the doted the right collision possibility. The behavior of the vehicle in each case can verified by observing the relative figures concerning the

37、 collision possibility in each direction.Fig. 10.Test Case 1. Environment with three obstacles and remote target point.Fig.11. Translational Velocity in Test Case Fig. 14. Left and right Collision Possibilities in Test Case 1.Fig.12. Rotational Velocity in Test Case 1. Fig. 15. Test Case 2. Environm

38、ent with three obstacles.Fig.13. Front Collision Possibility in Test Case 1. Fig.16. Translational Velocity in Test Case 2.Fig.17.Rotational Velocity in Test Case 2. Fig.20. Test Case . Environment with many small obstacles.Fig.18. Front Collision Possibility in Test Case 2. Fig.16. Translational Ve

39、locity in Test Case 3.Fig.19. Left and right Collision Possibilities in Test Case 2 Fig.22.Rotational Velocity in Test Case 3. Fig.23. Front Collision Possibility in Test Case 3.Fig.24. Left and right Collision Possibilities in Test Case 3.DISCUSSION AND CONCLUSIONS We have presented a navigation sy

40、stem for a skid steering vehicle with the use of a two-layer fuzzy logic controller. The first layer of the fuzzy logic controller is composed of four fuzzy logic controllers. The rule base of the controllers responsible for front and back collision contains 60 rules and the rule base of the control

41、lers responsible for front and back collision contains 57 rules. The rule base of the second layer fuzzy logic controller responsible for real-time navigation and collision avoidance contains 238 rules. The fuzzy logic controller has performed satisfactorily. The results show that the vehicle has th

42、e ability to move in complicated environments. The controller, which is proposed in this paper, is based in the controller proposed in 9 but it is implemented in a skid steering vehicle. Future directions of the research include the testing of dynamic environments, and the use of other sources of in

43、formation. The goal is to create an autonomous vehicle that will use for navigation and the collision avoidance combined information from visual inputs, sonars and outdoors GPS data that will guide the vehicle in remote target points.中译文模糊控制理论在自动引导车智能导航中的应用L. Doitsidis, K. P. Valavanis, N. C. Tsourv

44、eloudis（克利特科技大学生产过程和管理工程系，克利特岛，希腊，希腊GR-73100，电子邮箱： ldoitsidis, kimonv, nikostdpem .tuc .gr）摘要：本文设计了一种双层的基于模糊控制理论的控制器，用来在一个充满障碍物的环境下为自动引导车提供自主领航。控制器的第一层建立了一个复合的声纳传感器的输入端模型，它是由四个独立的控制器组成，这四个控制器分别用来计算自动引导车向前、后、左、右四个方向移动时碰撞可能性。第二层是由一个主控制器构成，它能计算自动引导车的行驶路线，因此能执行相应的程序以避免碰撞。通过对一个移动机器人进行研究证明了这个双层控制器的适用性。关键词

45、：自动引导，移动机器人，智能导航1 引言自主移动的机器人在2维不确定环境下的导航的问题，现存有很多方法，这些建议有的是以模糊控制理论的算法为基础的，还有的是把把模糊控制理论和调优算法结合起来的，以及把模糊控制理论和静电学领域结合起来的方法。 这篇文章是结合最近的一些研究成果而提出的。本文主要研究自动引导车的2维环境下的导航问题。自动引导车是坚实而轻巧的，只要求很少的装配部件，并且它可以很迅速的从点运动转变到线运动时, 本文导论的就是自动引导车的直线驾驶问题6.自动引导车和明确指点车的运动的不同在于自动引导车的转弯方式. 轮子的转动被限于绕一条轴 , 方向盘的缺陷导致导航由每边的速度变化决定。只

46、要任一方向有相同速度就将导致自动引导车沿直线运动。而明确指点车的轮子绕着两条轴转动。自动引导车 在 X-Y 平面里的几何结构如图1所示,在这张图里,表示的是航向角度,w表示的是机器人的宽度,自转角和S1、S2时该车在每个方向的速度。.2.模糊逻辑控制系统的设计 为了控制车的移动，一个双层的Mamdani型的控制器已经设计出来并完成。在第一层，四个模糊控制器负责对障碍物的探测和对前后左右四个方向的碰撞可能性进行计算。这四个控制器接收来自声纳传感器的数据，同时输出前后左右四个方向的碰撞的可能性。这些可能性在第一层中计算出来并和角度误差一起被输入到第二层中，输出量是车的最新的平移和旋转速度。图1.

47、自动引导车在X-Y平面上的模型A. 模糊逻辑控制器的第一层在自动引导车周围装有24个超声波传感器，如图2所示。这里所用到的这些超声波传感器由Polaroid制造。在测试一些关于声纳传感器数据编组和管理之后，最初决定按照文献8的方法对传感器编组 (把小测距系统中的十二台生波探侧器的传感器编组为Ai, i=1,4a., 12,如图2)，然后再把来自两组传感器的一对数据分开来讨论，可以得到潜在障碍物的距离。然而，由于 小型测距系统特有的声纳传感器的不可靠性, 这个方法得到的结果不尽如人意，当车附近有障碍时，传感器却探测到一条“自由道路”。为了解决这个问题，本文提出了一个改进的,更简单的传感器编组和数

48、据管理方法，并得到了更好更准确的结果：对图2的传感器再编组，它们的读数的最小数是到障碍物的距离的一个衡量值。 每个ATRV生波探侧器传感器以4米作为最大距离，从这个距离处的障碍物返回数据。(这由生波探侧器传感器制造商进行了实验性地核实).图2. 传感器组第一层的每个独立的模糊控制器的模型，即障碍物探测模块，如图3所示。从图3可知，对前、后方向的碰撞可能性的测定由传感器A1,A2,A5（5个输入数据）和传感器A7,A8,A11（5个输入数据）完成，而对左、右方向的碰撞可能性的测定由传感器A5,A6,A7（3个输入数据）和传感器A11,A12,A13（3个输入数据）完成，每个独立的模糊控制器利用隶属度函数来计算碰撞的可能性。距离障碍物的距离按照隶属度函