2022年Cisco交换机密码恢复大全 .pdf

《2022年Cisco交换机密码恢复大全 .pdf》由会员分享，可在线阅读，更多相关《2022年Cisco交换机密码恢复大全 .pdf（11页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、Cisco 交换机密码恢复大全一.基于 CatOS的 CATALYST 1200,1400,2901,2902,2926T/F,2926GS/L,2948G,2980G,4000,5000,5500,6000与 6500 密码恢复:关掉交换机电源,等待片刻再打开.当出现密码提示符后,接下来要做的事情,就是在 30 秒内完成一些步骤：1.回车(相当于输入空密码).2.进入 enable mode(enable命令别说你不会).3.回车,继续玩空密码.4.修改密码(set password和 set enablepass命令).5.回车,相当于输入旧密码(如果在这时候收到提示信息说sorry pa

2、ssword incorrect,抱歉,你动作太慢了,超过 30 秒了,把上述步骤重新做1 次,动作快点).6.设置更为安全的密码(set password和 set enablepass命令).完工.示例:System Bootstrap,Version 5.3(1)Copyright(c)1994-1999 by Cisco Systems,Inc.c6k_sup1 processor with 65536 Kbytes of main memory Autoboot executing command:boot bootflash:cat6000-sup.6-3-3.bin Uncomp

3、ressing file:#System Power On Diagnostics DRAM Size.64 MB Testing DRAM.Passed NVRAM Size.512 KB Level2 Cache.Present System Power On Diagnostics Complete Boot image:bootflash:cat6000-sup.6-3-3.bin 名师资料总结-精品资料欢迎下载-名师精心整理-第 1 页，共 11 页 -Running System Diagnostics from this Supervisor(Module 1)This may

4、take up to 2 minutes.please wait Cisco Systems Console 2002 Apr 08 16:08:13%SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 1 Enter password:/-你只有 30 秒-/(回车)2007 Mar 08 11:08:15%SYS-1-SYS_ENABLEPS:Power supply 1 enabled 2007 Mar 08 11:08:15%SYS-1-SYS_ENABLEPS:Power supply 2 enabled 2007 M

5、ar 08 11:08:18%SYS-5-MOD_PWRON:Module 3 powered up 2007 Mar 08 11:08:18%SYS-5-MOD_PWRON:Module 4 powered up 2007 Mar 08 11:08:25%MLS-5-NDEDISABLED:Netflow Data Export disabled 2007 Mar 08 11:08:26%MLS-5-MCAST_STATUS:IP Multicast Multilayer Switching is enabled 2007 Mar 08 11:08:26%SYS-5-MOD_OK:Modul

6、e 1 is online Console enableEnter password:2007 Mar 08 11:08:37%SYS-5-MOD_OK:Module 3 is online 2007 Mar 08 11:08:37%SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 3 Console(enable)set passwordEnter old password:(回车)Enter new password:(回车)Retype new password:(回车)Password changed.Console(

7、enable)set enablepassEnter old password:(回车)Enter new password:(回车)Retype new password:(回车)Password changed.其他些老古董比如CATALYST 1200 和这个有点不太一样,不写了,实在需要的话查 documentation 吧.二.CATALYST 2900,3500XL的密码恢复:名师资料总结-精品资料欢迎下载-名师精心整理-第 2 页，共 11 页 -拔下交换机的电源线,然后按住交换机的Mode按钮,再重新插上交换机的电源线.直到端口 Port 1x 的LED熄灭之后释放 Mode按

8、钮.就这么简单,别告诉我你不知道Mode按钮在哪啊-_-#三.CATALYST 2940,2950L的密码恢复:拔下交换机的电源线,然后按住交换机的Mode按钮,再重新插上交换机的电源线.直到 STAT的 LED熄灭之后释放 Mode按钮.四.CATALYST 2955的密码恢复:CATALYST 2955没有没有外部的 Mode按钮,因此就不能使用之前的那种方法来进行密码恢复.在交换机启动时,对于 Windows系列的 PC,按下 Ctrl+Break键;对于 UNIX系列的工作站,按下 Ctrl+C.如下:C2955 Boot Loader(C2955-HBOOT-M)Version 12

9、.1(0.0.514),CISCO DEVELOPMENT TEST VERSION Compiled Fri 13-Dec-02 17:38 by madison WS-C2955T-12 starting.Base ethernet MAC Address:00:0b:be:b6:ee:00 Xmodem file system is available.Initializing Flash.flashfs0:19 files,2 directories flashfs0:0 orphaned files,0 orphaned directories flashfs0:Total byte

10、s:7741440 flashfs0:Bytes used:4510720 flashfs0:Bytes available:3230720 flashfs0:flashfs fsck took 7 seconds.done initializing flash.Boot Sector Filesystem(bs:)installed,fsid:3 Parameter Block Filesystem(pb:)installed,fsid:4 /-接下来交换机会在15 秒内自动启动,等出现该信息之后,按下 Ctrl+Break键或 Ctrl+C 键-/The system has been i

11、nterrupted prior to initializing the flash file system to finish loading the operating system software:flash_init load_helper bootswitch:switch:flash_init /-输入 flash_init命令-/Initializing Flash.flashfs0:143 files,4 directories flashfs0:0 orphaned files,0 orphaned directories flashfs0:Total bytes:3612

12、672 flashfs0:Bytes used:2729472 flashfs0:Bytes available:883200 flashfs0:flashfs fsck took 86 seconds.done Initializing Flash.Boot Sector Filesystem(bs:)installed,fsid:3 Parameter Block Filesystem(pb:)installed,fsid:4 名师资料总结-精品资料欢迎下载-名师精心整理-第 3 页，共 11 页 -switch:switch:load_helper /-输入 load_helper命令-

13、/switch:switch:dir flash:/-查看交换机 flash内容-/Directory of flash:/2-rwx 1803357 c3500 xl-c3h2s-mz.120-5.WC7.bin 4-rwx 1131 config.text 5-rwx 109 info 6-rwx 389 env_vars 7 drwx 640 html 18-rwx 109 info.ver 403968 bytes available(3208704 bytes used)switch:switch:rename flash:config.text flash:config.old /

14、-重命名交换机配置文件-/switch:switch:boot /-手动启动交换机-/Loading flash:c3500 xl-c3h2s-mz.120-5.WC7.bin.#File flash:c3500 xl-c3h2s-mz.120-5.WC7.bin uncompressed and installed,entry po int:0 x3000 executing.进入 CLI 后:Switch#rename flash:config.old flash:config.text /-恢复交换机配置文件-/Destination filename config.text Switc

15、h#Switch#copy flash:config.text system:running-config /-把配置文件保存到DRAM 里-/Destination filename running-config?1131 bytes copied in 0.760 secs Switch#接下来做的就是取消密码和保存新的配置:Switch(config)#no enable secret Switch#wr Building configuration.OK Switch#名师资料总结-精品资料欢迎下载-名师精心整理-第 4 页，共 11 页 -五.CATALYST 3550,3560,3

16、750 的密码恢复:启动超级终端:拔掉交换机的电源.按下交换机上的Mode按钮,与此同时,重新插上交换机的电源线.当交换机端口 1X上的 LED熄灭后可以松开Mode按钮 1 到 2 秒.之后将显示一些指示信息:The system has been interrupted prior to initializing the flash file system.The following commands will initialize the flash file system,and finish loading the operating system software:flash_in

17、it load_helper boot switch#Switch#flash_init /-初始化 flash文件系统-/Switch#load_helper /-加载帮助文件-/Switch#rename flash:config.text flash:config.text.old /-显示 flash里的内容,把配置文件重命名-/Switch#boot /-手动启动交换机-/Switch#rename flash:config.old flash:config.text /-恢复交换机配置文件-/Switch#copy flash:config.text system:running-

18、config /-保存配置到 DRAM 里-/Switch(config)#enable secret password /-干掉旧密码,设置新密码,并保存-/Switch#wr六.基于 CISCO IOS软件版本 12.2(17)SX 之前的,搭载 Supervisor Engine 720的 CATALYST 6500 密码恢复:标题同样很长-_-3.本 section只适用于基于 CISCO IOS软件版本 12.2(17)SX 或其之前版本的.(关于这 1 部分的恢复过程,也可以参见 CISCO Bug ID CSCec36997 这 1 部分的讲解).通常当交换机加电后,交换机处理器

19、(SP)启动,大约 25-60 秒后,控制权转交给路由处理器(RP,MSFC),RP继续加载软件镜象.接下来要做的,老规矩,CTRL+BREAK,但是别太快,该过程是应该在 RP启动的时候做而不是在SP启动的时候做,否则就进到 SP ROMMON模式去了.因此,出现以下信息后,就可以 CTRL+BREAK了:00:00:03:%OIR-6-CONSOLE:Changing console ownership to route processor注意由于之前提到的bug,这次更猛,你只有 10 秒的时间去 CTRL+BREAK(看来是前作大片的续集啊-_-#).接下来修改寄存器值为0 x2142

20、 让交换机忽略启动配置文件.然后就会重启:rommon 1 confreg 0 x214200:00:41:%SYS-SP-3-LOGGER_FLUSHED:System was paused for 00:00:00 to ensure co.00:00:41:%SYS-SP-2-INTSCHED:t_idle at level 7 -Process=SCP Download Process,ipl=7,pid=57 -Traceback=4013991C 401232B4 402827F4 40282994 40283010 405CB010 402A9858 4013C 名师资料总结-精

21、品资料欢迎下载-名师精心整理-第 5 页，共 11 页 -00:00:41:%SYS-SP-2-INTSCHED:t_idle at level 7 -Process=SCP Download Process,ipl=7,pid=57 -Traceback=4013991C 401232B4 402827F4 40282994 40283010 405CB010 402A9858 4013C 00:00:41:%SYS-SP-2-INTSCHED:t_idle at level 7 -Process=SCP Download Process,ipl=7,pid=57 -Traceback=40

22、13991C 401232B4 402827F4 40282994 40283010 405CB010 402A9858 4013C 00:00:41:%OIR-SP-6-CONSOLE:Changing console ownership to switch processor *System received a Software forced crash*signal=0 x17,code=0 x24,context=0 x4269f6f4 PC=0 x401370d8,Cause=0 x3020,Status Reg=0 x34008002 之后不要进 setup 模式,进入命令行后,

23、enable 命令进到特权模式.然后 configure memory或 copy startup-config running-config命令伺候,把 NVRAM 中的东西拷贝到 RAM 中.继续,进到全局配置模式后,用 enable secret命令修改密码.然后把寄存器值改回0 x2102.如果你 VTY线路下设置的有密码,这时候可以顺便一起改了:Router(config)#line vty 0 4 Router(config-line)#password NUAIKORouter(config-line)#Z Router#最后保存配置:wr 吧.收工!示例:System Boot

24、strap,Version 7.7(1)Copyright(c)1994-2003 by cisco Systems,Inc.Cat6k-Sup720/SP processor with 524288 Kbytes of main memory Autoboot executing command:boot disk0:s72033-ps-mz.122-14.SX1.bin Self decompressing the image:#Restricted Rights Legend Use,duplication,or disclosure by the Government is subje

25、ct to restrictions as set forth in subparagraph(c)of the Commercial Computer Software-Restricted Rights clause at FAR sec.52.227-19 and subparagraph(c)(1)(ii)of the Rights in Technical Data and Computer Software clause at DFARS sec.252.227-7013.cisco Systems,Inc.170 West Tasman Drive San Jose,Califo

26、rnia 95134-1706 Cisco Internetwork Operating System Software IOS(tm)s72033_sp Software(s72033_sp-SP-M),Version 12.2(14)SX1,EARLY DEPLOY)TAC Support:http:/ 6 页，共 11 页 -Copyright(c)1986-2003 by cisco Systems,Inc.Compiled Tue 27-May-03 20:48 by ccai Image text-base:0 x40020C10,data-base:0 x40B98000 00:

27、00:03:%PFREDUN-6-ACTIVE:Initializing as ACTIVE processor 00:00:03:%OIR-6-CONSOLE:Changing console ownership to route processor /-你只有 10秒 CTRL+BREAK-/System Bootstrap,Version 12.2(14r)S9,RELEASE SOFTWARE(fc1)TAC Support:http:/ by cisco Systems,Inc.Cat6k-Sup720/RP platform with 524288 Kbytes of main m

28、emory Download Start*Mistral Interrupt on line 4*System memory 1 bit ECC correctable error interrupt.PC=0 x8000841c,SP=0 x80007f00,RA=0 x80008488 Cause Reg=0 x00004400,Status Reg=0 x3041c003 rommon 1 rommon 1 confreg 0 x2142You must reset or power cycle for new config to take effect.rommon 2 /-自动重启了

29、,别怕-/00:00:31:%SYS-SP-3-LOGGER_FLUSHED:System was paused for 00:00:00 to ensure co.00:00:31:%SYS-SP-2-INTSCHED:t_idle at level 7-Process=SCP Download Process,ipl=7,pid=57-Traceback=4013991C 401232B4 402827F4 40282994 40283010 405CB010 402A9858 4013C 00:00:31:%SYS-SP-2-INTSCHED:t_idle at level 7-Proc

30、ess=SCP Download Process,ipl=7,pid=57-Traceback=4013991C 401232B4 402827F4 40282994 40283010 405CB010 402A9858 4013C 00:00:31:%SYS-SP-2-INTSCHED:t_idle at level 7-Process=SCP Download Process,ipl=7,pid=57-Traceback=4013991C 401232B4 402827F4 40282994 40283010 405CB010 402A9858 4013C 00:00:31:%OIR-SP

31、-6-CONSOLE:Changing console ownership to switch processor*System received a Software forced crash*signal=0 x17,code=0 x24,context=0 x4269f6f4 PC=0 x401370d8,Cause=0 x3020,Status Reg=0 x34008002 System Bootstrap,Version 7.7(1)Copyright(c)1994-2003 by cisco Systems,Inc.Cat6k-Sup720/SP processor with 5

32、24288 Kbytes of main memory Autoboot executing command:boot disk0:s72033-ps-mz.122-14.SX1.bin 名师资料总结-精品资料欢迎下载-名师精心整理-第 7 页，共 11 页 -Self decompressing the image:#Restricted Rights Legend Use,duplication,or disclosure by the Government is subject to restrictions as set forth in subparagraph(c)of the C

33、ommercial Computer Software-Restricted Rights clause at FAR sec.52.227-19 and subparagraph(c)(1)(ii)of the Rights in Technical Data and Computer Software clause at DFARS sec.252.227-7013.cisco Systems,Inc.170 West Tasman Drive San Jose,California 95134-1706 Cisco Internetwork Operating System Softwa

34、re IOS(tm)s72033_sp Software(s72033_sp-SP-M),Version 12.2(14)SX1,EARLY DEPLOY)TAC Support:http:/ by cisco Systems,Inc.Compiled Tue 27-May-03 20:48 by ccai Image text-base:0 x40020C10,data-base:0 x40B98000 00:00:03:%PFREDUN-6-ACTIVE:Initializing as ACTIVE processor 00:00:03:%OIR-6-CONSOLE:Changing co

35、nsole ownership to route processor System Bootstrap,Version 12.2(14r)S9,RELEASE SOFTWARE(fc1)TAC Support:http:/ by cisco Systems,Inc.Cat6k-Sup720/RP platform with 524288 Kbytes of main memory Download Start!Download Completed!Booting the image.Self decompressing the image:#Restricted Rights Legend U

36、se,duplication,or disclosure by the Government is subject to restrictions as set forth in subparagraph(c)of the Commercial Computer Software-Restricted Rights clause at FAR sec.52.227-19 and subparagraph(c)(1)(ii)of the Rights in Technical Data and Computer Software clause at DFARS sec.252.227-7013.

37、cisco Systems,Inc.170 West Tasman Drive San Jose,California 95134-1706 名师资料总结-精品资料欢迎下载-名师精心整理-第 8 页，共 11 页 -Cisco Internetwork Operating System Software IOS(tm)s72033_rp Software(s72033_rp-PS-M),Version 12.2(14)SX1,EARLY DEPLOY)TAC Support:http:/ by cisco Systems,Inc.Compiled Tue 27-May-03 20:40 by

38、ccai Image text-base:0 x40008C10,data-base:0 x41ACE000 cisco Catalyst 6000(R7000)processor with 458752K/65536K bytes of memory.Processor board ID SR71000 CPU at 600Mhz,Implementation 0 x504,Rev 1.2,512KB L2 Cache Last reset from power-on X.25 software,Version 3.0.0.Bridging software.1 Virtual Ethern

39、et/IEEE 802.3 interface(s)96 FastEthernet/IEEE 802.3 interface(s)58 Gigabit Ethernet/IEEE 802.3 interface(s)1917K bytes of non-volatile configuration memory.8192K bytes of packet buffer memory.65536K bytes of Flash internal SIMM(Sector size 512K).-System Configuration Dialog-Would you like to enter

40、the initial configuration dialog?yes/no:nPress RETURN to get started!00:00:03:%SYS-3-LOGGER_FLUSHED:System was paused for 00:00:00 to ensure conso.00:00:46:curr is 0 x10000 00:00:46:RP:Currently running ROMMON from F1 region 00:01:00:%SYS-5-RESTART:System restarted-Cisco Internetwork Operating Syste

41、m Software IOS(tm)s72033_rp Software(s72033_rp-PS-M),Version 12.2(14)SX1,EARLY DEPLOY)TAC Support:http:/ by cisco Systems,Inc.Compiled Tue 27-May-03 20:40 by ccai 00:01:00:%SNMP-5-COLDSTART:SNMP agent on host Router is undergoing a cold stat 00:01:00:%SYS-6 Router-BOOTTIME:Time taken to reboot after

42、 reload=1807 seconds Firmware compiled 19-May-03 10:54 by integ Build 100 00:00:54:%SPANTREE-SP-5-EXTENDED_SYSID:Extended SysId enabled for type vlan 00:00:54:SP:SP:Currently running ROMMON from F1 region 00:01:00:%SYS-SP-5-RESTART:System restarted-Cisco Internetwork Operating System Software IOS(tm

43、)s72033_sp Software(s72033_sp-SP-M),Version 12.2(14)SX1,EARLY DEPLOY)名师资料总结-精品资料欢迎下载-名师精心整理-第 9 页，共 11 页 -TAC Support:http:/ by cisco Systems,Inc.Compiled Tue 27-May-03 20:48 by ccai 00:01:01:%OIR-SP-6-INSPS:Power supply inserted in slot 1 00:01:01:%C6KPWR-SP-4-PSOK:power supply 1 turned on.00:01:01

44、:%OIR-SP-6-INSPS:Power supply inserted in slot 2 00:01:01:%C6KPWR-SP-4-PSOK:power supply 2 turned on.00:01:01:%C6KPWR-SP-4-PSREDUNDANTBOTHSUPPLY:in power-redundancy mode,system.00:01:05:%FABRIC-SP-5-FABRIC_MODULE_ACTIVE:the switching fabric module in sloe 00:01:06:%DIAG-SP-6-RUN_MINIMUM:Module 5:Run

45、ning Minimum Diagnostics.Router Router 00:01:18:%DIAG-SP-6-DIAG_OK:Module 5:Passed Online Diagnostics 00:01:18:%OIR-SP-6-INSCARD:Card inserted in slot 5,interfaces are now online 00:01:21:%DIAG-SP-6-RUN_MINIMUM:Module 4:Running Minimum Diagnostics.Router Router Router 00:01:36:%DIAG-SP-6-RUN_MINIMUM

46、:Module 9:Running Minimum Diagnostics.Router Router 00:01:42:%DIAG-SP-6-RUN_MINIMUM:Module 1:Running Minimum Diagnostics.00:01:44:%DIAG-SP-6-DIAG_OK:Module 4:Passed Online Diagnostics 00:01:45:%OIR-SP-6-INSCARD:Card inserted in slot 4,interfaces are now online 00:01:54:%DIAG-SP-6-DIAG_OK:Module 9:Pa

47、ssed Online Diagnostics 00:01:54:%OIR-SP-6-INSCARD:Card inserted in slot 9,interfaces are now online 00:01:57:%DIAG-SP-6-DIAG_OK:Module 1:Passed Online Diagnostics 00:01:57:%OIR-SP-6-INSCARD:Card inserted in slot 1,interfaces are now online 00:02:06:%DIAG-SP-6-RUN_MINIMUM:Module 2:Running Minimum Di

48、agnostics.00:02:15:%DIAG-SP-6-DIAG_OK:Module 2:Passed Online Diagnostics 00:02:15:%OIR-SP-6-INSCARD:Card inserted in slot 2,interfaces are now online Router RouterenableRouter#copy startup-config running-config Destination filename running-config?(回车)4864 bytes copied in 2.48 secs(2432 bytes/sec)sup

49、720#sup720#configure terminalEnter configuration commands,one per line.End with CNTL/Z.sup720(config)#enable secret NUAIKOsup720(config)#config-register 0 x2102sup720(config)#line vty 0 4sup720(config-line)#password 91Labsup720(config-line)#Z sup720#copy running-config startup-configDestination file

50、name startup-config?(回车)Building configuration.名师资料总结-精品资料欢迎下载-名师精心整理-第 10 页，共 11 页 -OK sup720#reloadProceed with reload?confirm (回车)七.基于 CISCO IOS的 CATALYST 6000/6500密码恢复:本 section只适用于基于 Supervisor Engine 1/2/720的系统,并且对于 Supervisor Engine 720,本section针对的是 CISCO IOS软件版本 12.2(17)SX 或其后续版本的,之前版本的恢复参考,