2022年模具邮件英语 .pdf

《2022年模具邮件英语 .pdf》由会员分享，可在线阅读，更多相关《2022年模具邮件英语 .pdf（9页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、1 XXX！你现在 有空 吗，我可以问你一些问题吗？Could I ask you some questions if you are free?/Are you free now?May I ask you some questions (a question)?2 请问此产品的面是否 为外观面？表面做什么处理？是晒纹/抛光？Can you tell me whether the surface of this part is a visible/esthetic one?What will we do for its surface?Texture or Polishing?3 请问产品这

2、个面可否加顶针或顶块？产品允许加扁顶针 吗？Does this part need an ejector pin or an ejector bar?Can we add an ejector blade?4 这个产品的柱位我们打算做司筒。（或镶针）可以吗？Can we add ejector sleeves or ejector pins in the boss of this part?5 产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？Theres an undercut at this position and it needs a slider.It will

3、also have a parting line on this side,is that OK?6 产品里面的这个位置我们打算做斜顶或内行位，有问题吗？We will make the lifter and(inner)slider in this position,will that be a problem?7 你提供的 2D产品图与3D 产品图不一致，请问以哪一个图面为准？The 2D and 3D drawing you provided is not the same,can you tell me which one is correct?8 你提供的 3D产品图有的地方没有出模

4、角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。There is no draft angle in the 3D drawing,some materials are too thick,and some place are too thin.Can we modify this part by ourselves?We will send the drawing to you for you to check after we modify it.9 按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的

5、产品图。请确认你们的材料的缩水率是否正确？Accoring to the shrinkage one over two hundred,the mold has been done in the right dimension,but the part falls short to your part drawing,are you sure the shrinkage is right?10 产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗？This position is too small and will make the steel material here too thi

6、n,can we widen it here?11 斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移动这个柱子的位置吗？The angular lifter interferes with the boss during ejection.Please consider changing the Position of the boss.12 这个筋骨位胶厚太溥，而且高度偏高，注塑时很难填充这个筋位，可以增加这个筋骨位的厚度吗？The rib here is too thin and on the high side,so it will be difficult to fill he

7、re when we do the injection,can you inrcease the thickness of this rib?13 你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公放电加深。但减胶的位置有两种做法，1、做镶件；2、烧焊；因为镶件的底部有运水，我们简单的做法是烧焊处理，你可以接受吗？Will you increase/decrease the material on this rib?We will use EDM if you add material,but there are two option if you choose to decrease

8、:1.Make inserts;2.Welding,because there is water in the bottom of the insert,is that OK?14 这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在筋骨位的中间增加一个镶件。This sample has been burned in the bottom because the venting is not good,we can add an insert in 名师资料总结-精品资料欢迎下载-名师精心整理-第 1 页，共 9 页 -the middle of the rib.15 重做镶件大约需要5-6

9、 天时间，你能接受吗？It will take about 5 or 6 days to redo the insert,is that OK?16 产品的这个面我们已经做了晒纹处理，如果需要加胶，这个面我们需要重新外发晒纹。可能需要几天的时间。所以我们直接以铜公放电的火花纹取代你要求的纹路，你可以接受吗？We have made the texture on this side,if we add material,it will take some days to remake the texture by out-resourcing,so we suggest using the te

10、xture by EDM instead,is that OK?17 模具是用公制/英制的配件？需要备用件吗？Is this mold dimension measured in inches or meters?Does it need spare parts?18 模具上铭牌上的刻字内容是由你们提供吗？你们什么时候可以这些刻字资料。Will you provide the engraving content of the plate of this mold to us?When will you send it?19 可否提供此模具生产时，注塑机的型号及相关资料。如：啤机大小、呵林柱尺寸

11、、顶棍孔尺寸等Can you provide the type of injection machine and other related information of this mold to us?Such as the boss dimension,the holes dimension of the ejector pin and the size of the injection machine and so on.20 这个问题我需要同其它同事商议会再答复你。I need to discuss this problem with the other colleagues and

12、then I will reply back to you.21 我们将尽力达成你的计划，如有异常，会及时通知你。We will try our best to complete your plan,if there are any complications,we will notify you immediately.22.这个产品的长度为330.12MM,宽度为 78.96MM,高度为 45MM.胶厚为 2MM,重量为 70.63g,试模注塑机型号为250 吨,胶料颜色为黑色,产品外表面晒纹处理,内表面为抛光.需要日期章、环保章、材料章.前后模用2344 氮硬，斜顶和行位座用738H，以

13、上模具信息正确吗？请确认！The length of this part is 330.12MM,Width is 78.96MM,height is 45MM,thickness is 2MM,weight is 70.63g,the injection machine is 250T,the material is black,the outside of the part has texture,inner side needs polishing,and it also needs a date and recycle stamp,the core&cavity is 2344 nit

14、ridng,the lifter and slider shelf is 728H.Please check the information above!23 现在到了吃午钣的时间，我们下午再继续好吗？It is time to have lunch,lets discuss this project later this afternoon?24.和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動(The undercut area interferes with the slide block and needs to be filled with material to Help the sl

15、ider move smoothly.)25.加肉太多 (The thickness added is too thick.)26.加肉面積太大 (The thickening area is too wide.)27.GATE位置移位 (The gate position is moved.)28.滑塊拆的位置 (The split line of slide block or the area of slide.)29.此處有尖角，填充困難(It is hard to fill this area due to the sharp feature.)30.此處鋼材太薄，強度不足而且不容易冷

16、卻(The strength of this area is too weak and it is hard to cool because the steel is too thin.)31.圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷(We avoid designing the semicircle of the cylinder on the slide block because it will 名师资料总结-精品资料欢迎下载-名师精心整理-第 2 页，共 9 页 -be pulled apart or cause drag marks.)32.此處做斜銷在作動時會削

17、到成品肉厚(The part will be damaged if we make the lifter in this area.)33.這個面是裝配面，不能加料(This is a critical surface where we cannot add additional material.)34.此處料位太厚，會有縮水，建議減料改善(Because of the shrinkage of the thickness,we suggest reducing some wall thickness to improve it.)35.此面是不是外觀面，此處做滑塊的話會有夾線，是否可以接受

18、(Please confirm whether it is a critical surface or not.Also,confirm whether it is acceptable to have a slide split line if we have a slide in this area.)36.此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷(Please confirm whether we can reduce material to the area where we have an undercut as indicated to have shut off on

19、cavity side.No slide block and lifter will be made.)37.請盡快確認這種拆模方式和結構，否則會影響模期(Please confirm the issues of Parting line,Gate position.Etc.as soon as possible;otherwise,the lead-time will be extended.)38.此面是否有特殊要求，能否有頂針印(Please confirm whether it is a critical surface or not and if we can have E.J.pi

20、n marks on it.)39.P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響(There are sharp edges if we set the parting line here,It will reduce the tool life)40.加大拔模角，以便脫模順利(We suggest enlarging the draft angle to help release the tool.)41.GATE 做在此處的話有兩個缺點：1.蓋子打開時可以看到GATE的修剪部位;2.兩個斜銷在同一側，頂出也不是很平衡.(There are two problems if the

21、 gate is to be designed in this area:a).It is easy to see the gate mark when you open the cap.b).The ejectors are unbalanced when two lifters are on the same side)42.GATE 做在此處的話.蓋子打開後看不到GATE的修剪部位(The gate mark is not visible if the gate position is designed like this.)43.如果 GATE一定要做在你們指定的位置的話，那還不如做在

22、這一側，這樣的話還可以減小這個位置的縮水(If you insist that the gate position has to be like the original design,then we would further recommend to have it to the area indicated so it can avoid a shrink problem in this area.)44.在此處 GATE做潛頂針的話，背後的外觀面會有沖料痕，而且成品又是黑色的，會最明顯(If the design of the gate has to be a sub.Gate,the

23、n the back surface of the part will have serious flow marks due to the black colour.)22.P.L開在此處不合理，模具加工困難，P.L 應改為和圖示的一樣(This area is not suitable to have a Parting line because the tool will become more complicated;therefore,we recommend to have the Parting line as indicated.)45。产品粘母模的機會很大，能否在公模加倒勾，

24、拉料頂針或者公模保留E.D.M 紋，開模時使成品留在公模一側(There is possible sticking on cavity;therefore,please confirm whether it can make undercuts,snatch pins or leave coarse E.D.M.on the core to snatch the part on)名师资料总结-精品资料欢迎下载-名师精心整理-第 3 页，共 9 页 -46.此處料厚段差很大，成品表面會有應力痕，是否接受(Please confirm whether it is acceptable to hav

25、e stress lines on the surface because the Thickness is not equal.)47.請注明何處為外觀面，能否提供2D圖和注意事項(Please advise where the critical surface is.Please also provide us a 2D drawing with critical dimensions.)48.紅色所示處是有問題的地方，請特別注意(Please note the red highlights because those areas have problems.)49.成品設計此處有問題，建

26、議如下圖所示修改(We would suggest using the attached part design as the current design has problems.)50.此處改為一個球形的凹槽(We suggest modifying it as a globe recess.)51.圓柱特征要有一半不可以拆在滑塊裡，以防拉斷(this issue is the same as no.8)52.此處大滑塊上走小滑塊，小滑塊要先退，大滑塊要做延遲(The inside small slide block will recede first and the parent sl

27、ide block have to postpone sliding.)53.滑塊要用液壓油缸抽芯以保証開合模順序(The slide pins will use an oil cylinder to assure that the process is in proper order.)54.這個面有裝配，加料的話裝配時會頂住，如圖所示(We cannot add material to this surface because it will intervene between the two parts when it is assembled.Please see the sketch

28、 attached.)55.可降低斜銷面，增加成品些許肉厚來做變化(To descend the surface of lifter in order to thicken the part.)56.一半做斜銷，一半做自然(One half side will have the lifter and the other half will be solid/nature.)57.此處兩個柱子重疊，有倒勾，不能做自然，要做SLIDE(These two bosses are overlapping with undercut therefore it can not be made as sol

29、id.We suggest making it with a slide block.)58.此處強迫頂出 (This area needs force ejection.)59.公模兩段開模，這個地方先退(Here will be a double ejection for forward and receding.)60.此處做鑲件會有夾線，能否接受(Please confirm whether it is acceptable that there will be a split line here.)61.此面公母模1 度靠破，會有段差，可否接受(Please confirm whet

30、her it is ok to have mismatch to the area where there is 1 degree of shut off in Core/Cavity side.)62.這個尺寸能否加大(Please confirm whether we can enlarge this dimension.)63.此處加一個凹槽，膠片的彈出效果會更好一些，試模後看裝配的效果再做修正(It will affect the elastic of the film better if we add a recess.See how it will affect the assem

31、bly parts,and then make your decision.)64.此處有倒勾，建議將剖面線所示部位CUT即可避免此處的倒勾(There is an undercut here,we suggest cutting out the indicated part as it highlighted to avoid an undercut.)65.成型後 SUB GATE要修平 (The gate(sub gate)needs to be trimmed evenly after being moulded.)66.此處倒勾先垂直頂出，之後再手動取出(This area of t

32、he undercut needs to be ejected vertically,then taken out manually.)名师资料总结-精品资料欢迎下载-名师精心整理-第 4 页，共 9 页 -67.這兩個面都有滑塊，GATE改在此處改不到(The gate is not suitable in this area becuase there are two sliding blocks sealing off this area.)68.此處加做一個旋轉GATE，射出時方便調整成品的品質(We would suggest placing a runner shut-off in

33、sert to adjust the volume of part filling.)69.此倒勾在滑塊上強迫脫模，倒勾是否可以減小到0.6(This undercut will be force ejected out,Please confirm whether it can be reduced to 0.6 mm.)70.此柱子無法脫模，請確認是否是在轉圖時錯位，能否提供客戶的原始圖檔 data.)(This boss is not releasable.Please check the file again and if possible,pleas re-send us the o

34、riginal draft.71.此柱子是實心的，會縮水(This boss will shrink because it is a solid boss.)72.這個面是否要咬花，咬花番號是什麼，最小的拔模角要多大(Please confirm whether this surface needs to be textured or not.Please advise texture specs.Also,whats the min.draft.)73.這個面是否要打光，貼標簽(Please confirm whether this surface needs to be polished

35、and stuck on a sticker.)74.紅色顯示的幾個面拔模角太小，出模時會拉傷，建議加大拔模角(The red highlighted area has a problem of a small draft angle.We suggest enlarging the draft to avoid casuing drag marks on the part.)75.此 RIB 太薄，會填充不足(This rib can not be filled properly because it is too thin.)76.此 RIB 太厚，會縮水 (This rib will h

36、ave a shrink problem because it is too thick.)77.此處倒勾出模困難，建議先不做倒勾，成型後再二次加工，但要做治具，費用要另外算(There are problems with this current design,we recommend doing this undercut as an alternative but there will be additional costs.)78.柱子底部都要做火山口(The base of all bosses require a crater to avoid shrinkage.)1.镶件，P.

37、L.面有充足排气坑，P.L.面要开环形排气槽,并能将气体排到模外。Insert/PL should have adequate venting,PL should have around slot for venting.79.顶棍孔镶件端面距离底板面0,5mm,攻 m20牙;the surface of KO insert shound below bottom plate 0.5mm,thread M20.80.回针，中托司与模胚部份避空0.5mm；RP,EGP should have 0.5mm gap with the moldbase.81.排气槽距封胶位10-15mm；Ventin

38、g slot distance from the seal off position 10-15mm82.运水进用 E ，运水出用 S ；IntakeE,OuttakeS83.底面板均要有隔热板,DME规格 1/4 厚；Top/Bottom plate must have insulator plate,DME standard 4/1H84.吊环要在模具的重心（保证吊模时的平衡）;Eyebolt should on the center of the mold(for balance)85.吊模螺丝的位置要在前/后模部份的重心,保持平衡；The eyebolt position on the

39、 cavity/core side should on the center of gravity for balance86.唧嘴分试模唧嘴/走模唧嘴;Sprue type:Trial/Delivery名师资料总结-精品资料欢迎下载-名师精心整理-第 5 页，共 9 页 -87.喉塞选用：NPT规格;Plug use NPT spec.88.中托司采用HASCO 滚珠形式.Use HASCO ball EGP89.水咀采用法国标准:1/4的水咀写:RPL08-1151Jiffy Use French Standard:1/4 mark:RPL08-11511.和滑塊干涉的倒勾請加料填平至滑塊

40、可以順利滑動(The undercut area where interfere with slide block need to be filled material to help the slider can move smoothly.)2.加肉太多 (The thickness is added too thick.)3.加肉面積太大(The thickening area is too wide.)4.GATE 位置移位 (Gate position is moved.)5.滑塊拆的位置(The split line of slide block or the area of sl

41、ide.)6.此處有尖角，填充困難(This area is hard to be filled due to the sharp feature.)7.此處鋼材太薄，強度不足而且不容易冷卻(The strength of this area is too weak and isn t easy to get cold due to the steel to thin.)8.圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷(The semicircle of cylinder avoids designing on slide block lest it will be pulle

42、d apart or cause drag mark)9.此處做斜銷在作動時會削到成品肉厚(The part will get damage if we make lifter in this area.)10.這個面是裝配面，不能加料(This is critical surface where is not allow to add material.)11.此處料位太厚，會有縮水，建議減料改善(Owing to the shrinkage of the thickness that we suggest to reduce some wall thickness to improve i

43、t.)12.此面是不是外觀面，此處做滑塊的話會有夾線，是否可以接受(Please confirm whether it is critical surface or not.Please confirm whether it is acceptable to has Slide split line if we have slide in this area.)13.此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷(Please confirm whether we can reduce material to the area where have undercut as indicate

44、d to have shut off on cavity side.No slide block and lifter to be made.)14.請盡快確認這種拆模方式和結構，否則會影響模期(Please confirm the issues of Parting line,Gate position.Etc otherwise the lead-time will be extended.)15.此面是否有特殊要求，能否有頂針印(Please confirm whether it is a critical surface or not and can we have E.J.pin m

45、ark on it.)16.P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響(There are sharp edges if set the parting line at here,It will reduce the tool life)17.加大拔模角，以便脫模順利(We would suggest to enlarging draft to help tool released.)18.GATE 做在此處的話有兩個缺點：1.蓋子打開時可以看到GATE的修剪部位;2.兩個斜銷在同一側，名师资料总结-精品资料欢迎下载-名师精心整理-第 6 页，共 9 页 -頂出也不是很平衡.(T

46、wo imperfect points if the gate is to be designed in this area as below:a).Easy to see the gate mark when you open the cap.b).Unbalance of ejector when two lifters are at the same side)19.GATE 做在此處的話.蓋子打開後看不到GATE的修剪部位(The gate mark is not visual if the gate position is design like it.)20.如果 GATE一定要做

47、在你們指定的位置的話，那還不如做在這一側，這樣的話還可以減小這個位置的縮水(If you insist that the gate position have to be as original design then we would further recommend to have it to the area where indicate as it 21.在此處 GATE做潛頂針的話，背後的外觀面會有沖料痕，而且成品又是黑色的，會最明顯(If the gate type has to be design as sub.gate then the back surface of par

48、t will have flow mark with serious due to black colour.)22.P.L開在此處不合理，模具加工困難，P.L 應改為和圖示的一樣(This area is not suitable to have Parting line as the tool will become more complicate therefore we recommend to have Parting line as indicated.)23.此成品粘母模的機會很大，能否在公模加倒勾，拉料頂針或者公模保留E.D.M 紋，開模時使成品留在公模一側(It is pos

49、sible sticking on cavity,therefore,please confirm whether it can make undercuts,snatch pins or leave coarse E.D.M.on core to snatch part on)24.此處料厚段差很大，成品表面會有應力痕，是否接受(Please confirm whether it is acceptable to has stress line on surface,it is cause to the thickness isnt equally.)25.請注明何處為外觀面，能否提供2D圖

50、和注意事項(Please advise where is the critical surface.Please also provide us 2D drawing with critical dimensions.)26.紅色所示處是有問題的地方，請特別注意(Please pay more attention to the area where highlighted as red co lour as this area have problem.)27.成品設計此處有問題，建議如下圖所示修改(We would suggest to have part design as attache