供应商零件交付要求PPT讲稿.ppt
《供应商零件交付要求PPT讲稿.ppt》由会员分享,可在线阅读,更多相关《供应商零件交付要求PPT讲稿.ppt(11页珍藏版)》请在淘文阁 - 分享文档赚钱的网站上搜索。
1、供供应商零件交付要商零件交付要求求4/21/09Ford Motor ConfidentialPrinted&Saved Copies are UNCONTROLLED1第1页,共11页,编辑于2022年,星期四4/21/09Ford Motor ConfidentialPrinted&Saved Copies are UNCONTROLLED2Guidelines for Level 2 Measuring PointsL2测量点的测量原则测量点的测量原则(From Document DCD 01-008 rev 4/12/07)NOTE:All measurements are to be
2、 taken from documented datums.所有测量必须有文件资料记录For components,use the following guidelines:单件测量原则Cut lines on outer skin panels are to be read out for margin and flushness as follows:外观件间隙段差搭接边的测量遵循以下原则:At 50 mm intervals for straight areas.直线段间隔50 mm 测量At 25 mm intervals for sweeping areas or radii.圆弧边
3、或曲边间隔25mm测量Mating surfaces,seal surfaces,flanges,and trim lines are to be read out at 50 mm intervals.匹配面,密封面,翻边以及切边线间隔50mm 测量Holes,other than weight-reduction holes,are to be measured for location and size.除减重孔外的其它孔需要测量大小及位置尺寸A point within 3 mm of the tangent of each radius must be measured.每个曲线段的
4、切线3mm内需要测量一个点。All form features are to have at least three points per line.所有外形特征线每条至少测量3点Grid the product surface into 150 mm squares and check at least one point per square.每150mm 的正方形面内至少需要测量1点,Level 2 points are a subset of Level 1 points(for components only)and must include Level 3 points.L1测量点
5、包含所有L2测量点,L2测量包含L3测量点For subassemblies,use the following guidelines:分总成测量原则All locators that are used to build the assembly are to be measured.所有用于装夹零件的定位点必须测量Cut lines on outer skin panels are to be read out for margin and flushness as follows:外观件间隙段差搭接边的测量遵循以下原则:At 100 mm intervals for straight ar
6、eas.直线段间隔100 mm 测量At 50 mm intervals for sweeping areas or radii.圆弧边或曲边间隔50mm测量All seal surfaces and mating surfaces are to be read out at 200 mm intervals.匹配面,密封面,边缘以及切边线 间隔200mm 测量Grid the product surface into 300 mm squares and check at least one point per square.每300mm 的正方形面内至少需要测量1点第2页,共11页,编辑于
7、2022年,星期四4/21/09Ford Motor ConfidentialPrinted&Saved Copies are UNCONTROLLED3Part Data Submission Requirement零件数据提交要求零件数据提交要求Data is to be submitted with the physical part for each PCF event.The data is to contain the following information and is to be formatted to follow the intent of the examples
8、that follow.The format does not have to match the exact appearance.数据须与实物零件一起提交。数据须包含以下信息并遵循附例格式要求The data submission package is to include the following:数据提交包含以下内容PIST Summary of Level 2 Points(Level 3 Points for Modified/Carry-Over Parts)L2测量点的PIST(L3点用于改善件/共用零件)Table summary broken out per Exampl
9、e A(include summary by form,trim,holes and total)on next page用图示范例A的表格(包含外形,切边,孔和总计)进行测量点汇总Illustration or manual sketch indicating the+and deviation reporting convention the data follows per Example B on next page按图例B用插图或草绘图显示正负偏差Illustration or manual sketch indicating the datums used when the par
10、t was measured per Example C on next page按图例C用插图或草绘图测量时的原始数据第3页,共11页,编辑于2022年,星期四4/21/09Ford Motor ConfidentialPrinted&Saved Copies are UNCONTROLLED4(+)(-)(-)(+)Example AExample BExample CPart Data Submission Requirements(cont.)零件数据提交要求零件数据提交要求第4页,共11页,编辑于2022年,星期四4/21/09Ford Motor ConfidentialPrint
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 供应商 零件 交付 要求 PPT 讲稿
限制150内