FCC 68500 美国通信联邦委员会.pdf

《FCC 68500 美国通信联邦委员会.pdf》由会员分享，可在线阅读，更多相关《FCC 68500 美国通信联邦委员会.pdf（68页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、35047 CFR Ch.I(10199 Edition)68.404the original complaint and which re-late to the original cause of action maybe filed with the Commission.68.404Number of copies.An original and two copies of allcomplaints and amended complaintsshall be filed.An original and one copyof all other pleadings shall be

2、filed.68.406Service.(a)The Commission will serve a copyof any complaint or amended com-plaint filed with it,together with a no-tice of the filing of the complaint.Such notice shall call upon the defend-ant to satisfy or answer the complaintin writing within the time specified insaid notice of compla

3、int.(b)All subsequent pleadings andbriefs shall be served by the filingparty on all other parties to the pro-ceeding in accordance with the require-ments of 1.47.Proof of such serviceshall also be made in accordance withthe requirements of said section.68.408Answers to complaints andamended complain

4、ts.Any party upon whom a copy of acomplaint or amended complaint isserved under this subpart shall servean answer within the time specified bythe Commission in its notice of com-plaint.The answer shall advise the par-ties and the Commission fully and com-pletely of the nature of the defense,and shal

5、l respond specifically to allmaterial allegations of the complaint.In cases involving allegations of harm,the answer shall indicate what actionhas been taken or is proposed to betaken to stop the occurrence of suchharm,both in terms of future produc-tion and with reference to articles inthe possessi

6、on of distributors,sellers,and users.Collateral or immaterialissues shall be avoided in answers andevery effort should be made to narrowthe issues.Matters alleged as affirma-tive defenses shall be separately statedand numbered.Any defendant failingto file and serve an answer within thetime and in th

7、e manner prescribed maybe deemed in default.68.410Replies to answers or amend-ed answers.Within 10 days after service of an an-swer or an amended answer,a com-plainant may serve a reply which shallbe responsive to matters contained insuch answer or amended answer andshall not contain new matters.Fai

8、lureto reply will not be deemed an admis-sion of any allegation contained insuch answer or amended answer.68.412Defective pleadings.Any pleading filed in a complaintproceeding not in substantial con-formity with the requirements of theapplicable rules in this part may bedismissed.68.414Hearing aid-c

9、ompatibility:En-forcement.Enforcement of 68.4 and 68.112 ishereby delegated to those states whichadopt those sections and provide fortheir enforcement.The procedures fol-lowed by a state to enforce those sec-tions shall provide a 30-day period aftera complaint is filed,during which timestate personn

10、el shall attempt to re-solve a dispute on an informal basis.Ifa state has not adopted or incorporated68.4 and 68.112,or failed to act within6 months from the filing of a complaintwith the state public utility commis-sion,the Commission will accept suchcompliants.A written notification tothe complain

11、ant that the state believesaction is unwarranted is not a failureto act.49 FR 1368,Jan.11,1984Subpart FConnectorsSOURCE:41 FR 28699,July 12,1976,unlessotherwise noted.68.500Specifications.General.The US customary units areshown in parentheses throughout thissubpart F.US customary units werethe origi

12、nal dimensional units used indesigning the plugs and jacks shown inthe following pages.The dimensionsshown without parenthesis are in SIunits.The SI dimensional units are de-rived from the US customary units byVerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00350Fmt 8010Sfmt 8010Y:SGML183186T.XXX

13、pfrm08PsN:183186T351Federal Communications Commission68.500multiplying inches by 25.4 to de-rive the exact conversion in millime-ters with no rounding-off of the result-ing decimal value.The number of dec-imal places to which the conversion istaken by adding a particular number ofzeroes to the right

14、 end of the resultingSI value,where required,is governedby the concept that when the cal-culated SI dimensional unit is dividedby 25.4,the resulting inches cal-culation will be exactly that shown inthe parenthesis(the original design di-mension).The conversion to SI forceunits,newtons,is rounded off

15、 to anumber of decimal places that will re-sult in the calculated SI force valuebeing within less than one percent ofthe original US customary force unitvalue located adjacent in parenthesis(the original design value).The ration-ale for this is that this ill bring theforce conversions to within the

16、degreeof accuracy of the force-measuring de-vice and avoid the carrying of an unre-alistic number of decimal places whichwould otherwise result from an exactconversion.The plugs and jacks de-scribed in this section represent thestandard connections to be used forconnections to the telephone network.

17、The plug and jack designs shown arerepresentative of generic types,andshould not be interpreted as the onlydesigns that may be used.Design inno-vation and improvement is expected;but for interchangeability to be main-tained,alternative designs(the orequivalent permitted in 68.104)mustbe compatible w

18、ith the plugs and jacksshown.The interface dimensions be-tween mating plugs and jacks must bemaintained.Hardware used to mount,protect,and enclose standard jacks isnot described.The only requirement onconnecting blocks,housings,dust cov-ers,outdoor boxes,and the like thatcontain standard network jac

19、ks is thatthey accept standard plugs with cord-age.For special purpose applications,plugs may be made longer than shownor adapted for direct use on equipmentor apparatus without cordage.The slid-ing modular plug used on the back ofmany modular wall telephone sets is anexample of such a special purpo

20、se ap-plication.It is the responsibility of thedesigners and manufacturers of com-munication equipment who use suchplugs to assure that they are compat-ible with the hardware used to mountstandard jacks with which they plan tointerface.For the purposes of this sec-tion,hard gold and contact perform-

21、ance equivalent to gold shall be deter-mined in accordance with the stand-ards detailed in Appendix H of TIATelecommunications Systems BulletinNo.31 Part 68 Rationale and Measure-ment Guidelines(TSB.31),prepared byEIA/TIA TR41 Committee on Tele-phone Terminals(1992).This publica-tion may be obtained

22、 by contactingGlobal Engineering Documents,7730Carondelet Avenue,Suite#407,St.Louis,Missouri,63105.(Telephone num-ber 18008547179).(a)Minature 6-position plug:VerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00351Fmt 8010Sfmt 8010Y:SGML183186T.XXXpfrm08PsN:183186T35247 CFR Ch.I(10199 Edition)68.50

23、0VerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00352Fmt 8010Sfmt 8006Y:SGML183186T.XXXpfrm08PsN:183186T353Federal Communications Commission68.500VerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00353Fmt 8010Sfmt 8006Y:SGML183186T.XXXpfrm08PsN:183186T35447 CFR Ch.I(10199 Edition)68.500NOTES:(N

24、otes apply to Figures 68.500(a)(2)(i)and 68.500(a)(2)(ii)1.All plugs must be capable of meeting therequirements of the plugs go and no-gogauges.VerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00354Fmt 8010Sfmt 8010Y:SGML183186T.XXXpfrm08PsN:183186T355Federal Communications Commission68.5002.Secti

25、on BB applies to any jack contact re-ceiving slot which does not contain a plugcontact.3.The preferred major cordage cross sectionis 2.5400 mm(.100 inch)max.thick by 5.0800mm(.200 inch)max.wide,with roundedcorners.It should exit the plug on the plugcenterline.Other cordage configurationsare permitte

26、d but may inhibit the specialfeatures of some network jack enclosures.4.The standard plug length is 11.6840 mm(.460 inch)max.Plugs may be made longerthan standard or adapted for direct use onspecial cords,adapters with out cordage,and on apparatus or equipment subject tothe limitations described in

27、the Section68.500 introductory paragraphs.Plugslonger than standard may inhibit the spe-cial features of some network jack enclo-sures.5.A 12.0396 mm(.474 inch)minimum tablength is required.It is preferred that amaximum tab length be no longer than13.2080 mm(.520 inch).Longer tabs may beused with th

28、e same limitations as de-scribed in Note 4.6.To obtain maximum plug guidance when 6-position plugs are inserted in 8-positionjacks,it is desirable to extend the frontplug nose to the 2.3368 mm(.092 inch)max-imum.7.These dimensions apply to the location ofjack contact receiving slots.It is desirablet

29、hat plug contacts be centered axially inthese slots,but centering is not required.8.The 6.0452/6.1722 mm(.238/.243 inch)dimen-sion is preferred to obtain maximum plugguidance in jacks with more than 6 conduc-tors.A tolerance range of 5.9182/6.1722 mm(.233/.243 inch)is permitted,but may createtargeti

30、ng problems in 8-position jacks.9.The center rib centerline shall be coinci-dent with the plug width 9.6520 mm(.380inch)ref.centerlinewithin+/.0762mm(+/.003 inch).VerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00355Fmt 8010Sfmt 8010Y:SGML183186T.XXXpfrm08PsN:183186T35647 CFR Ch.I(10199 Edition)6

31、8.500NOTES:(Notes apply to Figure 68.500(a)(3)(i)1.The plug/jack contact interface should behard gold to hard gold and should have aminimum gold thickness of.0012700 mm(0.000050 inch)on each side of the interface.The minimum contact force should be.98 N(100 grams).Any non-gold contact materialmust b

32、e compatible with gold and provideequivalent contact performance.A smooth,burr-free surface is required at the inter-face in the area shown.2.The jack contact design is based upon.4572mm(.018 inch)spring temper phosphorbronze round wire in the modular plugblade and jack contact interface.Othercontac

33、t configurations that provide con-tact performance equal to or better thanthe preferred configurations and do notcause damage to the plug or jack are per-mitted.The preferred jack contact width is.44958/.49530 mm(.0177/.0195 inches).Devi-ations from the preferred jack contactwidth are permitted for

34、round contacts aswell as noncircular cross sectional shapesbut they must be compatible with existingplug configurations.The requirements ofNote 1 apply to all possible contact areas.3.The configuration of the plug contact andthe front plastic of the plug should preventVerDate 299901:47 Nov 24,1999Jk

35、t 183186PO 00000Frm 00356Fmt 8010Sfmt 8010Y:SGML183186T.XXXpfrm08PsN:183186T357Federal Communications Commission68.500jack contacts from being damaged duringplug insertion into jacks.4.This is the suggested nominal contactangle between plugs and jacks with theplug latched into the jack.If this angle

36、 be-comes greater than 24 degrees loss of elec-trical contact may occur between the plugand jack.If the nominal contact angle be-comes less than 13 degrees,interference be-tween jack contacts and the internal plas-tic in the plug may occur.5.To avoid loss of electrical contact,the pre-ferred dimensi

37、on from datum B to thehighest point X should be 5.0800 mm(.200inch)max.A dimension greater than 5.3594mm(.211 inch)may result in loss of elec-trical contact between plugs and jacks.The 5.3594 mm(.211 inch)max.shall be con-sidered an absolute maximum.6.The 24 degree min.angle applies only toplugs wit

38、h front plastic walls higher than4.8260 mm(.190 inches).VerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00357Fmt 8010Sfmt 8010Y:SGML183186T.XXXpfrm08PsN:183186T35847 CFR Ch.I(10199 Edition)68.500VerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00358Fmt 8010Sfmt 8006Y:SGML183186T.XXXpfrm08PsN:18

39、3186T359Federal Communications Commission68.500(b)Miniature 6-position jack:(1)ReservedVerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00359Fmt 8010Sfmt 8010Y:SGML183186T.XXXpfrm08PsN:183186T36047 CFR Ch.I(10199 Edition)68.500VerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00360Fmt 8010Sfmt 80

40、06Y:SGML183186T.XXXpfrm08PsN:183186T361Federal Communications Commission68.500NOTES:(Notes apply to Figures 68.500(b)(2)(i)and 68.500(b)(3)(i).)1.Front surface projections beyond the 1.2700mm(.050 inch)min.shall be configured soas not to prevent finger access to the plugrelease catch(Reference Figur

41、e68.500(a)(2)(i),6-Position Plug,MechanicalSpecifications).A catch length greaterVerDate 299901:47 Nov 24,1999Jkt 183186PO 00000Frm 00361Fmt 8010Sfmt 8010Y:SGML183186T.XXXpfrm08PsN:183186T36247 CFR Ch.I(10199 Edition)68.500than 1.2700 mm(.050 inch)is beneficial inproviding greater breakout strength.

42、2.Surface Z need not be planar or coincidentwith the surface under the plug releasecatch.Surface Z projections must not pre-vent insertion,latching,and unlatching ofthe standard 6-position plug described in68.500(a).3.The preferred plug stop surface is indi-cated.If some other internal feature isuse

43、d as a plug stop,it must be located sothat the axial movement of a latched plugis no greater than 1.1430 mm(0.045 inch).4.To prevent mistargeting between the plugand jack contacts,the jack contactsshould be completely contained in their in-dividual contact zones,.7112 mm(.028 inch)max.wide,where the

44、y extend into the jackopenings.There is no location requirementfor jack contacts below these zones 5.8420mm(.230 inch)max.,but adequate contactseparation must be maintained to preventelectrical breakdown.These shaded con-tact zones should be centrally located,(in-cluded all locating tolerances),abou

45、t thejack opening width 9.8806 mm(.389 inch)Ref,(Datum-W-).Contacts located outsideof these zones may result in mistargetingbetween the jack and plug contacts.5.All inside and outside corners in the plugcavity to be.3810 mm(.015 inch)radiusmax.unless specified.6.These surfaces shall have 015 maximum

46、draft.7.Relief inside the dotted areas on 3 sides ofthe jack opening is permitted.The 6.8326mm(.269 inch)Ref and 9.8806 mm(.389inch)Ref Gauge Requirements must bemaintained in each corner,(ref.1.0160 mm(0.040 inch)min),to assure proper plug/jackinterface guidance.A.8128 mm.1270 mm(.032 inch.005 inch

47、)relief on the top side,(opposite plug catch),is required on jacksin connecting blocks which mount and con-nect portable wall telephones so as to as-sure interface with the special purposesliding modular plug used on many walltelephone sets.8.4.0640 mm(.160 inch)and 6.5278/6.8580 mm(.257/.270 inch)d

48、imensions to be centrallylocated to jack opening width-W-within.1778 mm(0.007 inch).9.Minimum acceptable jack contact length.When contact guide slots are used,the con-tacts must always be contained inside theguide slots and the contacts must movefreely in the slots so as not to restrain pluginsertio

49、n or damage jack contacts.10.Gauge Requirements:GO:The jack shall be capable of acceptinga 9.7536 x 6.7056 mm(0.3840 x 0.2640 inch)gauge and the gauge shall be capable ofbeing removed with a maximum force of8.9 newtons(2 pounds).NO GO:The jack shall not accept either a10.00760 x 6.45160 mm(0.3940 x

50、0.254 inch)horizontal width of opening gauge or a6.95960 x 9.5504 mm(.2740 x.376 inch)vertical height of opening gauge.How-ever,if either gauge is accepted the forcenecessary to remove the gauge shall beminimum.83 newtons(3.0 ounces).Removal forces do not include forces con-tributed by contact sprin