干网清洗机械维护常见报警信息处理.pdf

《干网清洗机械维护常见报警信息处理.pdf》由会员分享，可在线阅读，更多相关《干网清洗机械维护常见报警信息处理.pdf（54页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、DuoCleaner ExpressTM干网易清洗干网易清洗干网易清洗干网易清洗Lee&Man PM15VOITH 2011AMB Training|2DuoCleaner Express 管道流程图管道流程图管道流程图管道流程图AMB Training|3AMB Training|41 清洗头2 干网3 接水盘4 过程控制系统5 过滤系统6 高压泵站7 密封水槽8 气水分离器9 泵站10 清洗站11 横梁AMB Training|5ComponentsFlowsheet External Vacuum外接真空外接真空外接真空外接真空water高压水high pressureair压缩空气HP

2、-pumptraversing beamwash-boxwatervacuum line 真空管道4-6 m/min at 100-200 mbarcyclone气水分离器seal tankAMB Training|6DuoCleaner Express 清洗原理清洗原理清洗原理清洗原理air knife气刀water jet pump水喷射真空泵high pressure watersupply高压水外接真空catch pan接水盘干网运行速度200m/min.(连锁）?Air knife to blow remaining water out of the fabric?将残余的水分吹出干

3、网Suction by means of a water jet pump水喷射泵产生真空具有一定压力的工作介质水，通过喷嘴向吸入室高速喷出，将水的压力能变为动能，形成高速射流；吸入室中的气体被高速射流强制携带与之混合，形成气液混合流，进入扩压器，从而使吸入室压力降低，形成真空，在扩压器的扩张段内，混合射流的动能转变为压力能，速度降低压力升高，气体被进一步压缩，与水一起排出泵外，在水箱中气水分离，气体释放入大气，水由水泵循环再利用，周而复始达到抽真空的目的。单级水喷射泵的喷嘴可以是由一个渐缩喷嘴构成的单喷嘴结构，也可以是在一个孔板上开设多个孔口的多喷嘴结构。柱塞泵提供高压水，清洗与产生真空?C

4、leaning jet inclined against running direction?喷射方向与干网运行方向相反?Cleaning through wire in free draw Cleaning of surface and structure?穿透清洗，清洁表面与内部结构，保证干网透气度AMB Training|7Fabric direction干网运行方向Air knife气刀Water-jet vacuum pump水喷射真空泵（injector）高压水喷射产生真空Water-jet 高压水高压水高压水高压水DuoCleaner ExpressCleaning Head清洗

5、头清洗头清洗头清洗头catch pan 接水盘AMB Training|8Airknife气刀气刀气刀气刀Cleaningblock清洗块清洗块清洗块清洗块Cleaningnozzle喷嘴喷嘴喷嘴喷嘴Injectorblock水喷射真空泵水喷射真空泵水喷射真空泵水喷射真空泵DuoCleaner ExpressCleaning Head 分解后的清洗头分解后的清洗头分解后的清洗头分解后的清洗头清洗靴清洗靴清洗靴清洗靴AMB Training|90082.04.01Sealing lensordering No.0082.04.02xx(xx=*100/mmRound jet nozzleorde

6、r numberwith sealing lensSealing2000 barPressure range1.4305 with sapphire insertMaterialM8 x 1Threadpointed jetCharacter0.1 up to 1.7 mmDiameterMSD 2-0,20Round jet nozzleorder numberwith O-RingSealing2000 barPressure range1.4305 with ceramic insertMaterialM18 x 1Threadpointed jet 2;3;4;6Character0,

7、20;0,25;0,30DiameterDuoCleaner Expressnozzle specification 喷嘴规格喷嘴规格喷嘴规格喷嘴规格nozzle type 0082,=0.25 mmMSD3,=0.25 mmAMB Training|10DuoCleaner Express-Cleaning Head Maintenance清洗头维护清洗头维护清洗头维护清洗头维护1:喷水效果检查喷水效果检查喷水效果检查喷水效果检查Check the jet quality of the cleaning nozzles.(Visually inspect while the cleaning

8、 head is operating in park position)检查清洗喷嘴喷水效果检查清洗喷嘴喷水效果检查清洗喷嘴喷水效果检查清洗喷嘴喷水效果（肉眼检查清洗头在肉眼检查清洗头在肉眼检查清洗头在肉眼检查清洗头在P位置位置位置位置的喷水状况的喷水状况的喷水状况的喷水状况，应该为集中的水束应该为集中的水束应该为集中的水束应该为集中的水束）目的：1：检查喷嘴是否堵塞；2：过滤器是否堵塞严重；避免因为上述原因造成清洗效果不佳；建议每次停机开机前打到手动模式，将清洗头移至P位置，开启泵进行观察。2 to 6 needle jet nozzles in one nozzle body每个喷嘴有2至

9、6个针形孔Higher peel-off forces especially for large stickies产生很大的剥除力（特别对大的胶黏物）Jets support each other(no boundary layer of air),therefore less misting and contamination of the cleaning head.多束高压水柱无边流，清洗头较少的水雾和脏物AMB Training|112:更换清洗块滤芯和喷嘴更换清洗块滤芯和喷嘴更换清洗块滤芯和喷嘴更换清洗块滤芯和喷嘴?Remove cleaning block拆出清洗块?Open ma

10、le stud fitting(3)change filter(5)and check sealing ring拧出接头（3）（将清洗块固定在台虎钳上进行）更换滤芯（5）并检查密封圈?Re-insert filter and screw down the male stud couplingwith a drop of paste安装滤芯，拧紧接头（3）（涂抹螺纹胶）?Unscrew MSD nozzle(1)and check O-ring.旋出MSD喷嘴（1）并检查0形圈?Exchange the O-ring if it is damaged如果O形圈已经损坏则更换?Screw in t

11、he new MSD nozzle旋入新的MSD喷嘴DuoCleaner Express-Cleaning Head Maintenance清洗头维护清洗头维护清洗头维护清洗头维护根据水质情况，建议三个月检查更换滤芯AMB Training|12Running direction/MDNozzles parallel to CD：喷嘴要同喷嘴要同喷嘴要同喷嘴要同CD方向平行方向平行方向平行方向平行:To achieve that,the nozzle has to be tightened and then turned back until the alignment is parallel

12、 to CD.为达到这个目标为达到这个目标为达到这个目标为达到这个目标，清洗喷嘴必须首先被清洗喷嘴必须首先被清洗喷嘴必须首先被清洗喷嘴必须首先被拧紧拧紧拧紧拧紧，然后往回转一下然后往回转一下然后往回转一下然后往回转一下，直到喷嘴与直到喷嘴与直到喷嘴与直到喷嘴与CD方向平行方向平行方向平行方向平行The sealing is done by an O-ring,so it will be leak-proof also if not tightened.密封是通过密封是通过密封是通过密封是通过1个个个个O形圈实现的形圈实现的形圈实现的形圈实现的，所以即使所以即使所以即使所以即使喷嘴没有被拧紧的话

13、也不会滴水喷嘴没有被拧紧的话也不会滴水喷嘴没有被拧紧的话也不会滴水喷嘴没有被拧紧的话也不会滴水。Adjustment of Nozzle喷嘴调节喷嘴调节喷嘴调节喷嘴调节AMB Training|133：Drive Nozzle Exchange or cleanning水喷射真空泵喷嘴更换或清洁水喷射真空泵喷嘴更换或清洁水喷射真空泵喷嘴更换或清洁水喷射真空泵喷嘴更换或清洁DuoCleaner Express-Cleaning Head Maintenance清洗头维护清洗头维护清洗头维护清洗头维护?Remove cleaning block拆出真空发生块?Unscrew nozzles(1)f

14、rom the injector nozzle block(3)with Allen key 4mm用4mm内六角扳手将喷嘴(1)拆出?Remove the sealing discs(2).拆出密封(2)?Insert new sealing discs(2)into the nozzle block(3).?Screw-in cleaned or new nozzles(1)and tighten to a torque of 10 Nm.喷嘴拧紧力10Nm?Loosen threaded connection(5)to the filter(4).拆卸堵头（5）,检查密封圈（将组块固定在

15、台虎钳上进行）?Remove filter(4).拆除滤芯?Screw new filter(4)into nozzle block(3).安装新滤芯?Insert threaded connection(5)with a drop of paste安装堵头blind nozzles can be used in the upper row(marked red)to save water有时候为节约用水或降低泵的功率，在保证真空的前提下，使用堵头根据水质情况，建议三个月检查更换滤芯AMB Training|14DuoCleaner Express washing box Maintenanc

16、e清洗站维护清洗站维护清洗站维护清洗站维护1：扇形喷嘴清洁或更换停机时检查喷嘴是否堵塞，进行清洁。建议2个月清洁一次，具体根据水质情况。共13个2：密封橡胶皮更换如出现破损或缺失，进行更换。AMB Training|15DuoCleaner Express-Cleaning Head movement清洗头移动清洗头移动清洗头移动清洗头移动DS-FS传动侧往操作侧移动默认值 10Hz（清洗过程）FS-DS操作侧往传动侧移动回P位置默认值 50Hz(非清洗过程）AMB Training|16DuoCleaner Express Traversing Unit移动装置移动装置移动装置移动装置(1)

17、Traversing beam with openings for maintenance带维修孔的横梁(2)Limit switch 限位开关(3)Guide rolls(horizontal,vertical)导轮（水平，垂直）(4)Energy chain for high pressure water,air and waste water 桥架（内有高压水管，压缩空气管，废水管）(5)Trolley移动小车(6)Traversing motor with rope and tensioning unit 移动马达待钢丝绳和张紧装置(7)Guide rail 导轨(8)Cleaning

18、 head with water jet pump for extraction of dirt and water 清洗头AMB Training|17DuoCleaner Express-Cleaning Head movement清洗头移动清洗头移动清洗头移动清洗头移动变频马达（带传动轮）回转轮（带位置传感器与张紧装置）1：废水管2：钢丝绳固定头3：桥架4：钢丝绳5：车架6：移动滚轮7：导向滚轮8：压缩空气管9：高压水管钢丝绳未松懈不能手动移动清洗头避免安全销断裂AMB Training|18DuoCleaner Express traversing motor移动马达移动马达移动马达移

19、动马达马达齿箱AMB Training|19Service and MaintenanceChange of Shear Pin安全销的更换安全销的更换安全销的更换安全销的更换?Remove circlip(1)from the drive shaft(7).拆除传动轴上卡簧（1）；?Remove drive gear(2)from the drive shaft(7).拆除传动轮?Remove shear pin(5)from the drive shaft(7).拆除需要更换的安全销?Fit new shear pin.安装新安全销?Install all components in re

20、verse sequence to removal.反方向安装各部件AMB Training|20Turn back wheel of rope drive with REED Sensore钢丝绳驱动带传感器回转轮钢丝绳驱动带传感器回转轮钢丝绳驱动带传感器回转轮钢丝绳驱动带传感器回转轮传感器磁铁AMB Training|21Press the cable together withtwo fingers on this spotWheel=110mm(=4.3)?Adjustment screw张紧螺栓Tightening the Stainless Steel Cable钢丝绳的张紧钢丝绳

21、的张紧钢丝绳的张紧钢丝绳的张紧此部位两指压紧钢丝绳AMB Training|22DuoCleaner Express-Cleaning Head movement清洗头移动限位清洗头移动限位清洗头移动限位清洗头移动限位1：操作侧2：传动侧3：操作侧限位NNP(给转向信号）4：清洗站限位W5：P位置限位P6：操作侧限位NP7：移动装置操作侧传动侧NNP 0%NP100%W PAMB Training|23?Move DuoCleaner Express in service mode,coming from limit switch P(limit switch has hysteresis)t

22、o the corresponding limit switch.维护模式下，运行DCE从P位置到需要调整的限位位置?Mark current position of the cleaning boot(4)on the cross member.标记调整前清洗头位置?Measure distance(dimension D)to the correct limit switch position(in area C).测量目标位置距离D?Loosen the fastening screw(3)of the retaining plate(2).拆卸固定螺栓(2)?Pull retainin

23、g plate(2)out of the bayonet holder.移出保持架?Unscrew limit switch(1)from retaining plate(2).从保持架上拆卸限位开关?Move limit switch(1)by dimension D.移动限位开关，距离D?Tighten limit switch(1)onto retaining plate(2).锁紧限位开关?Push retaining plate(2)into the bayonet holder.将保持架归位?Tighten fastening screw(3).锁紧固定螺栓Chaning Posi

24、tion of Limit Switch 调整限位调整限位调整限位调整限位AMB Training|24Traversing Unit Maintenance 横梁维护横梁维护横梁维护横梁维护MaintenanceInterval.Check HP-piping,air piping and suction hose for leakage检查高压水管检查高压水管检查高压水管检查高压水管，压缩空气管和真空排管是否泄漏压缩空气管和真空排管是否泄漏压缩空气管和真空排管是否泄漏压缩空气管和真空排管是否泄漏Check for dirt inside the traverse beam检查清洗横梁内是否

25、有杂物检查清洗横梁内是否有杂物检查清洗横梁内是否有杂物检查清洗横梁内是否有杂物（特别是轨道上不应该有杂质特别是轨道上不应该有杂质特别是轨道上不应该有杂质特别是轨道上不应该有杂质）1 x weekly1次次次次/周周周周 或停机检查或停机检查或停机检查或停机检查（建议建议建议建议3个月清洁一次个月清洁一次个月清洁一次个月清洁一次）1 x monthly1次次次次/月或停机检查月或停机检查月或停机检查月或停机检查1 x monthly1 次次次次/月或停机检查月或停机检查月或停机检查月或停机检查Check the DuoCleaner for suspicious wear and damage,

26、specifically the steel cable,ride rolls,drive pulley and return pulley.检查可疑的磨损和损坏检查可疑的磨损和损坏检查可疑的磨损和损坏检查可疑的磨损和损坏，特别是钢丝绳特别是钢丝绳特别是钢丝绳特别是钢丝绳，小车移动轮和横梁两端的传动轮小车移动轮和横梁两端的传动轮小车移动轮和横梁两端的传动轮小车移动轮和横梁两端的传动轮和回转轮和回转轮和回转轮和回转轮1 x weekly1次次次次/周周周周 或停机检查或停机检查或停机检查或停机检查Check injector,snorkel and suction hose for dirt.C

27、lean with a pipe snake if required检查清洗真空驱动喷嘴检查清洗真空驱动喷嘴检查清洗真空驱动喷嘴检查清洗真空驱动喷嘴，清洗靴内部清洗靴内部清洗靴内部清洗靴内部，真空排管内部杂物真空排管内部杂物真空排管内部杂物真空排管内部杂物，气水气水气水气水分离器以及下面排管的清洁和疏通分离器以及下面排管的清洁和疏通分离器以及下面排管的清洁和疏通分离器以及下面排管的清洁和疏通AMB Training|25Pipeline cleaning 管道系统清洁管道系统清洁管道系统清洁管道系统清洁清洗头内部清洁清洗头内部清洁气水分离器清洁废水管清洁AMB Training|26Servi

28、ce und Instandhaltung-Traverse Wechsel Luft-und WasserschlauchService and MaintenanceExchange of hp hose 更换高压软管更换高压软管更换高压软管更换高压软管AMB Training|27Service and MaintenanceExchange of Waste Water Hose更换废水管更换废水管更换废水管更换废水管AMB Training|28Service and MaintenanceExchange of Energy ChainService and Maintenance

29、Exchange of hp chain 更换坦克链更换坦克链更换坦克链更换坦克链AMB Training|29PowerpackAMB Training|30Service and Maintenance-PumpReleasing Overpressure泄压保护泄压保护泄压保护泄压保护Here!安全阀安全阀安全阀安全阀AMB Training|31ComponentsWater Filter Station水过滤水过滤水过滤水过滤?For Filtering of the water supply to the high pressure pump?Filter inserts with

30、 1 m mesh 过滤精度1 m?Preferred water supply:mixture of fresh water and deionized water(1:10)with constant pressure of 2 5 bar进出口压差？AMB Training|32ComponentsMembrane Pressure Compensation隔膜式压力补偿器隔膜式压力补偿器隔膜式压力补偿器隔膜式压力补偿器?Mounted between filter and Powerpack?Assures constant pre-pressure to the pump even

31、if pre-pressure is fluctuating?安装与过滤器与泵之间，保证泵进口压力稳定AMB Training|33DuoCleaner-High Pressure PumpMaintenance高压泵维护高压泵维护高压泵维护高压泵维护MaintenanceCheck the oil level检查泵齿箱油位检查泵齿箱油位检查泵齿箱油位检查泵齿箱油位Check and change the water filter检查更换过滤器的滤芯检查更换过滤器的滤芯检查更换过滤器的滤芯检查更换过滤器的滤芯Oil change更换泵油更换泵油更换泵油更换泵油（油品与加入量见泵站顶盖油品与加入

32、量见泵站顶盖油品与加入量见泵站顶盖油品与加入量见泵站顶盖）Interval1 x weekly1次次次次/周周周周1 x weekly1次/周 或停机检查1 x monthly1次次次次/月月月月Check pump for leakage and excessive pulsation change seals,valves,plungers if necessary检查泵的漏水和脉冲检查泵的漏水和脉冲检查泵的漏水和脉冲检查泵的漏水和脉冲P,如果有必要更换密封圈如果有必要更换密封圈如果有必要更换密封圈如果有必要更换密封圈，阀门或泵杆阀门或泵杆阀门或泵杆阀门或泵杆压力表指针波动大时或压差大时5

33、00小时第一次，2000小时第二次，之后4000小时每次AMB Training|34Service and Maintenance-Pump Reasons for Pulsation泵压力波动的原因泵压力波动的原因泵压力波动的原因泵压力波动的原因High Pulsation(5%,at 12%the system switches off)can have two reasons:高脉冲（5，在12系统自动停泵）一般会有2个原因：?Dirt in Valves or defect valves 泵阀内有杂物或泵阀损坏?At least one of the sealings is brok

34、en 至少一个泵密封破了1st piston2nd piston3rd pistonPressure difference 23%PressureAnglePlunger pumps always show a certain amount of pulsation,at the display a value of 2-4%(much less than the theoretical 23%because of the high damping of the system)is absolutely normal.活塞泵会有一定范围的脉冲活塞泵会有一定范围的脉冲活塞泵会有一定范围的脉冲活塞

35、泵会有一定范围的脉冲，24（大大低于理论的大大低于理论的大大低于理论的大大低于理论的23，因为泵带有很高的阻尼系统因为泵带有很高的阻尼系统因为泵带有很高的阻尼系统因为泵带有很高的阻尼系统）的范围是完全正常的的范围是完全正常的的范围是完全正常的的范围是完全正常的。AMB Training|35Pump Reasons for Pulsation泵原因造成的脉冲泵原因造成的脉冲泵原因造成的脉冲泵原因造成的脉冲Dirt in Valves 阀内杂质阀内杂质阀内杂质阀内杂质If there is dirt in the valves,they cant close properly anymore.T

36、his leads to higher revolutions per minute and pulsation.If a new pump already shows pulsation when switching it on for the first time,dirt in the valves is a likely reason.如果泵单向阀有杂物，无法再关严，会导致泵更快的转速和更高的脉冲。特别是一个新泵在刚开机时就显示脉冲过高，那泵阀内有杂物应该是其原因。To flush out the dirt of the pump,open the blind plug at the

37、pulsation damping hose and switch on the pump.After a certain time the pump will switch off because of too high revolutions per minute.Acknowledge the alarm and redo the procedure for several times.为了把泵内的杂物冲出泵外，打开泵出口阻尼管一端的堵头，开启泵。泵的转速会越来越高，一段时间后泵会因为太高转速太高而跳停，复位报警，并重复上述操作，直至把泵内杂物冲出。Then close the blin

38、d plug and start the pump again.If there is still pulsation,you need to do service on the pump head or the sealings.If the sealings are ok,the valves are probably broken and you either need to exchange the valves or rather the whole pump head.然后堵上泵出口阻尼管的堵头，并开启泵。如果还有高脉冲，你应该对泵头或泵密封做检查维护，如果泵密封是好的，那泵阀可能

39、损坏了，更换泵阀或整个泵头。AMB Training|36Pump Reasons for Pulsation泵原因造成的脉冲泵原因造成的脉冲泵原因造成的脉冲泵原因造成的脉冲Sealings are defect密封圈损坏密封圈损坏密封圈损坏密封圈损坏If the sealings are defect(which can occur after some weeks or several months,depending on the water quality),water will flow with very high speed through the leaking areas a

40、nd not only destroy the sealings further,but also other parts like the drip return ring or the plungers.如果密封圈损坏了（根据水质量的差异，在新密封圈使用后几周或几月内可能发生），水流会以很快的速度流经泄漏区域，不仅进一步损坏密封圈，还会损坏其它部件如止回圈或泵活塞杆。Defect sealings lead to higher revolutions per minute and to pulsation.破损的密封圈将导致泵更高的转速和脉冲。AMB Training|37?Pump un

41、it with frequency controlled high pressure triplunger pump 变频控制三缸柱塞泵?max.operating pressure:640 bar?max.flow:33 l/minControl valves for water and air电磁阀控制水与压缩空气AMB Training|38Pump structure泵结构泵结构泵结构泵结构曲柄箱盘根盒单向阀组泵头AMB Training|39Stuffing box strcture盘根盒盘根盒盘根盒盘根盒Description/dimensionPos inFigureStuffi

42、ng box body d82/23x1171Pressure spring d28/3x23x3,52Bush d20/32x38 3Packing ring d20/32x6 4Bush d20/32x8 5Support ring d20/32x3,9 6Chevron ring d20/32x2,5x4,5 7Female adapter d20,2/32x8 8Circlip 32x1,2 10Cylinder pin 6h8x16-A1 13Splash guard d29/10 x1 14Gasket d10,4/17x3 15Hexagon screw M10 x110 16P

43、lunger ceramic piece d20/11x97 17AMB Training|40Check valve strcture单向阀单向阀单向阀单向阀Description/dimensionPos inFigureValve seat d47/6x33 1Valve plate d28,5/12x2,5 2Pressure spring d25/1,6x23x4 shot-blasted 3Spring seat d32/23x20 4Valve cone d10 x13,5 gehrtet 5Pressure spring d6/0,75x15x10 shot-blasted 6

44、Bush d10/16x30,5 7O-Ring d15,54x2,62 Nr.114 labs-frei 8Gasket d18,5/24x3 9O-Ring d40,94x2,62 Nr.130 10Cylinder head screw M6x12 11Bush d7/15x6 in collector force fitted 12AMB Training|41Gear box曲柄箱曲柄箱曲柄箱曲柄箱Description/dimensionPos inFigure Shaft sealing ring 30 x52x7-BA 4 Shaft sealing ring 55x70 x8

45、-BA 17AMB Training|42AMB Training|43sealing change盘根盒密封更换盘根盒密封更换盘根盒密封更换盘根盒密封更换1:loosen fixed screw 按如下顺序松懈螺栓1236548791211102:Draw out the pump head carefully 将泵头水平均匀拉出Notice:when pull out the pump head,some small parts easily fall down拉出泵头时小心小部件掉落丢失AMB Training|443:Draw out stuffing box respectively

46、 slowly and carefully将盘根盒水平均匀拉出4:Check plungers,Change them if necessary检查柱塞，必要时更换表面无明显划痕无点蚀无裂纹AMB Training|45change the plunger更换柱塞(1)unscrew the fixed bolt松懈螺栓(2)install new plunger安装新柱塞install washer 安装缺口垫片install washer,addsome lub.past to contact surface 垫圈接触面涂抹润滑膏tighten the bolt with torque w

47、rench after the stuffing box installation(make sure the level of plunger)为保证柱塞水平安装，将柱塞套入盘根盒，盘根盒与曲柄箱结合好后按近盘根盒，再按要求拧紧螺丝AMB Training|465:Dismount check valve from stuffing box 拆卸单向阀check sealing surface 检查单向阀密封面if the surface worn out serious,change a new one is necessayif it is worn out slight,use som

48、e chemical to polish AMB Training|476:Dismount high pressure seal from stuffing box 拆卸旧盘根draw out spring and bush取出压紧弹簧和护套draw out packing rings 用塑料棒从反面将盘根顶出draw out bush取出护套AMB Training|486:Dismount low pressure seal from stuffing box 拆卸低压侧密封draw out female adapter,chevronring,support ring 取出V形环和支撑

49、圈dismount circlip 拆卸卡簧AMB Training|497:Check the inner-surface of the stuffing boxpolish a lttile bit if it is necessary8:Pre-install the packing rings 预安装盘根检查盘根盒内表面，若轻微点蚀，用细砂纸打磨使用专用工具安装每个盘根缺口错开120度角AMB Training|509:Install-in reverse orders 按相反方向安装AMB Training|51报警信息：清洗器未准备好说明有某项清洗器开启的条件没有满足比如最常见的原

50、因：真空OK的信号没有从DCS反馈到清洗器的PLC此时需请自动化的检查真空OK的信号上图显示DCS已经开启，PLC也已经发出真空请求，但是真空OK的信号没有反馈AMB Training|52泵启动压力30bar没有达到可能的原因：1：管道泄漏大管道接头脱开或某处有大的泄漏；2：泵盘根磨损严重，造成压力上不起；3：泵启动速度设置太低，对于新泵或者没有大磨损的泵，一般启动速度为12%，如果一段时候后盘根有磨损，可以试试相应提高泵启动速度，比如设为16%，18%，如果仍然不能达到启动压力，泵密封需要更换AMB Training|53泵压力波动太大一般压力波动超过12%并且维持一定时间，泵会跳停可能原