积分球校准操作说明精选PPT.ppt

《积分球校准操作说明精选PPT.ppt》由会员分享，可在线阅读，更多相关《积分球校准操作说明精选PPT.ppt（40页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、积分球校准操作说明第1页，此课件共40页哦Photometry光度测量What is photometry?什么是光度测量Photometry is the measurement of light.光度测定是用来测量光If you cannot measure what you produce,you will not be in business for long.如果你不能测量你自己的产品,那么你不会有长久的买卖2第2页，此课件共40页哦Electromagnetic Spectrum电磁波频谱3第3页，此课件共40页哦Radiation辐射Light is the portion of

2、 the Electromagnetic Spectrum that can excite the retina and produce a visual sensation.光是电磁波频谱的一部分,它能刺激视网膜产生视觉Visible Light可见光380 to 800 nmUltraViolet Radiation紫外辐射UV-C -200 to 260 nmUV-B -260 to 320 nmUV-A -320 to 400 nm长波紫外线InfraRed Radiation红外辐射800 to 3600 nm4第4页，此课件共40页哦Relative Eye Sensitiviti

3、es眼睛相对的灵敏度Scotopic Eye Sensitivity Curve暗视觉灵敏度曲线Photopic Eye Sensitivity Curve适光5第5页，此课件共40页哦Integrating Spheres Why use them?积分球In practice,luminous flux is measured using an integrating sphere.习惯上积分球用来测量光通量The spheres are coated with a highly diffuse,reflective and spectrally flat coating.球面上覆盖有一层

4、高反射物质The advantage of a sphere is that the light from the test source is“integrated”via multiple reflections such that the reflected light striking any point on the sphere wall is proportional to the luminous flux emitted by the lamp.球的优势是测试源的光是”完整的”,经过多次反射,反射光照到球面内任何一个点上的灯发出的光通量是均衡的6第6页，此课件共40页哦Sys

5、tem Design系统设计Test Lamp测试灯Baffle挡片Detector探头Baffle挡片AuxiliaryLamp辅助灯Power System第7页，此课件共40页哦Sphere Design球设计Detector to measure the light output.探头测量光的输出Baffle to block the direct light from the lamp from the detector档片阻挡从灯管直接到探头的光We are interested in the integrated reflected light in the sphere not

6、 direct light(Illuminance).我们要测定的是在球内完整的反射光而不是直接照射光Auxiliary Lamp and baffle to monitor the sphere calibrations.辅助灯和挡片是监控球的标准8第8页，此课件共40页哦Sphere Photometer球面光度计9第9页，此课件共40页哦Sphere Theory球原理E=I/r2E=Illuminance照度I=Luminous Intensity发光强度10第10页，此课件共40页哦11E=I/AE=IlluminanceI=Luminous Intensity LINE 1 HAS

7、 ONE REFLECTION直线1有一个反射E1=r/ASphere Theory第11页，此课件共40页哦11222E=I/ALINE 2 HAS TWO REFLECTIONSE2=rr/ASphere Theory第12页，此课件共40页哦112223333E=I/ALINE 3 HAS THREE REFLECTIONSE3=rrr/ASphere Theory第13页，此课件共40页哦ETOTAL=I/r2+r/A+rr/A+rrr/A+.ETOTAL=I/r2+r/A+r2/A+r3/A+.ETOTAL=I/r2+/A S(r+r2+r3+.)ETOTAL=I/r2+r A(1-

8、r)Sphere TheoryETOTAL=r After Baffle Insertion to Block Direct A(1-r)The detector signal is proportional to luminous flux!探测到的信号与光通量成比例第14页，此课件共40页哦Basic Photometry Systems15第15页，此课件共40页哦Units:Lumens 1 lm is 1“light Watt”.单位:Lumens-1lm是1”光瓦”Eye sensitivity corrected power.Definition:The time rate of

9、 flow of radiant energy(radiant power)as weighted by the photopic spectral sensitivity of the eye.定义:光源在单位时间内所发出的光量,其中可产生视觉者If a uniform point light source of 1 cd luminous intensity is positioned at the center of a sphere of 1-m radius,every area of 1 m2 on the inside of the sphere will receive a l

10、uminous flux of 1 lm.如果在一个半径为1m的球内的中心位置有一个光强度为1cd的均匀点光源,在1 m2 内表面接收到的光通量是1lm.Luminous Flux()光通量16第16页，此课件共40页哦Determined by Equation:方程式P()is the spectral power distribution(SPD)of the light source in W/nmP()是光源的光谱能量分布W/nmV()is the photopic spectral sensitivity of the eye used here as a“weighting fa

11、ctor”V()是眼睛产生的视觉-”权重因数”This is the fundamental photometric equation这是光度的基本方程k=683 lm/W Luminous Flux()17第17页，此课件共40页哦P()=lamp power spectra灯能量范围V()=eye sensitivity curve视觉灵敏曲线P()*V()=effective power spectra the eye sees可见功率范围You can think of the eye as a detector with a response curve V()眼睛就象是V()曲线所

12、反应Photometry System Calibration18第18页，此课件共40页哦Photometry System Calibration光度系统标准Why calibrate?为什么用标准？Proper calibration links Philips measurements to Standard International Unitsoptical watt and lumen.飞利蒲测量单位是以国际单位为标准-瓦特和流明US Federal Trade Commission requires that ratings in catalogues,in advertisi

13、ng,etc be based in actual measurements.美国商务委员会要求刊登在目录、广告等要基于实物测量Many customers request certification to ANSI,CSA,or other standards.Photometric measurements are a part of many certifications.许多顾客要求有ANSI,CSA或者其它标准的认证。光度测量也是这些标准中的一部分。Governmental contracts(state and national)many times require certifi

14、cation.政府合同大多数要求有证明Philips Lighting is in the business of providing light and lighting solutions,NOT selling“light bulbs”.We must be able to measure what we sell.飞利蒲照明是供应灯和照明方案，不出售“电灯泡”。我们必须有能力测试我们所卖的。Luminous flux,color,CRI,Lifetime,etc is what we sell and how we differentiate ourselves from others

15、.我们出售的产品的光通量、色温、CRI、寿命等，如何与其它公司区别19第19页，此课件共40页哦Photometry System CalibrationWhy calibrate?Without good measurements,we cannot:没有好的测量法，我们没有好的测量法，我们不能不能：Determine our quality.决定我们的质量Judge the effectiveness of improvements or product cost reductions.判定效力的提升或者生产成本减少Properly analyze customer complaints.

16、完整的分析顾客抱怨Effectively bench mark the competition.有效的竞争基点Provide good data for court cases.提供对案例有益的资料Rebut competition claims and misinformation.反驳竞争要求和误传Support sales.支持销售20第20页，此课件共40页哦Fundamental Calibration Equation标准方程的基本原理Calibrations are typically performed by measuring a known value and then e

17、stablishing a Calibration Factor or Correction Factor as the ratio of the known and Measured Value:标准代表测量一个已知值，设定一个校准因数或者修正因数当作已知和测量值的比率Measured values of unknowns are then calculated as:测量未知值计算如下21第21页，此课件共40页哦Fundamental Calibration Equation方程基本原理The standard lamps are placed in the sphere and ope

18、rated at the electrical characteristics specified by the certificate标准灯放置在球内然后按照说明书进行电特性操作The flux value provided by the certificate is then used to determine the Calibration Factor:根据说明书提供的光通量值测定校准因数For some photometers(LMT I1000 and C1200s)this value can be entered in as the attenuator for the sys

19、tem.这个值可以当作是一些光度计系统的衰减器22第22页，此课件共40页哦Sphere Corrections球体修正Corrections must be applied to integrating sphere measurements to account for Lamp Color,Shape,Size,non-linear(or different)sphere illumination,fixturing,and Intensity Distribution.修正必须适用于累计球（光度计的圆球）测量说明灯的色温、外型、尺寸、非线形（或者不同）球照明、预定时间和亮度分布The

20、corrections are:修正如下：Self Absorption自吸收Spatial空间Intensity Distribution亮度分布Spectral光谱Positional位置23第23页，此课件共40页哦Photometry System Calibration光度测量系统标准There are typically only 2 calibrations required for photometry systems:光度测量系统典型的有2个要求标准Luminous flux(detector based)光通量（基于探头）Spectral光谱Once correction

21、factors are determined,the information can be put into calculation software(such as PDAQ)or spreadsheets and automatically used in the measurement process.一旦确定修正因数，资料应该被输入到计算软件（象PDAQ）或者电子数据表格，自动使用在测量程序中。24第24页，此课件共40页哦Photometry Systems CalibrationCalibration 1:Detector Based Calibration Luminous Fl

22、ux Calibration标准1：探头标准-光通量标准Lumens流明Includes SAF,ID,Spectral,Spatial,Positional Correction Factors包括SAF、ID、光谱、空间、位置、修正因数Equipment:LMT,sphere.设备：LMT、球Calibration 2:Spectral Based Calibration Spectral Power Distribution Calibration标准2：光谱标准-光谱能量分布Spectral Power Distribution光谱能量分布Used to calculate CCT,C

23、RI,x,y,all R-values习惯上计算CCT、CRI、X、Y、所有R值x,y correction factors are dependent upon this calibration,NOT the luminous flux calibration.X、Y的修正因数依赖于这个标准，不是光通量标准。This calibration is currently a“relative”calibration does not include corrections such as SAF,ID,etc.这个标准是当前“相对的”标准-不包括修正象SAF、ID等The calculated

24、 values need only relative values,not absolute values.计算值需要的只是相对值不是绝对值Equipment:DAS,OMA,Monochromator,Spectrometers,etc.设备：数据采集器、OMA、单色仪、分光计等。25第25页，此课件共40页哦Photometry Systems CalibrationCorrection factors applied to luminous flux can include:修正因数适用于光通量包括：Self Absorption Correction:A lamp in a spher

25、e absorbs light emitted by itself and reflected back from the sphere wall,thus reducing the sphere responsivity 自吸收修正：一支灯在球内吸收自身发出和球壁上反射的光，从而减少了球的敏感度Spectral Mismatch Correction:The spectral responsivity of the integrating sphere photometer is not perfectly matched to the eye sensitivity curve V()fu

26、nction.光谱失谐修正：积分球的光谱敏感度与人眼灵敏度曲线不是完全相等Spatial Non-uniformity Response Correction:The response of the sphere is not spatially uniform because of the baffle or other objects in the sphere(fixtures for u-bend),contamination of the sphere wall,gaps between hemispheres,different angular luminous-intensity

27、 distributions from those of the test lamp.空间不均匀反应修正：球内反应不是空间均匀的，因为在球内有挡光片和其它物体，球壁上的污染物，半球的空隙，测试灯从不同角度的照射。26第26页，此课件共40页哦Photometry Systems CalibrationCorrection factors applied to luminous flux can include:修正因数适用于光通量包括：Intensity Distribution Response Correction:The response of the sphere is not spa

28、tially uniform due to different angular luminous-intensity distributions from those of the test lamp as compared to the calibration lamp.强度分布反应修正：球体反应空间不一致取决于从标准灯不同角度发光亮度分布-Positional Correction:Ideally,all measured test lamps should be measured in the same positional orientation as the standard lam

29、ps during calibration procedures.In some cases,lamps must be measured in a different orientation.This correction is also important when making measurements on position limited lamps.In order to account for any effects that may occur due to a combination of non-uniform spatial issue with the sphere,a

30、 positional correction factor is used.-位置修正：理想上所有测试的试验灯应该安装在相同的位置方向按照标准灯的标准程序。有时候，灯必须在不同的方向上测试。这个修正同样重要当靠有限灯管来确定测量位置。为了解决任一效果的可能发生，取决于球的空间不一致问题，所以使用了位置修正因数。27第27页，此课件共40页哦Photometry Systems CalibrationCalibration 1:Detector Based Calibration Luminous Flux Calibration标准1：探头标准-光通量标准(1)Define the“null”

31、condition of the sphereExample:Empty socket,no lamp.定义球体“无效”条件 如：没有灯(2)Determine SAF of the calibration lamp standards 确定SAF标准灯的标准(3)Determine the Attenuator Setting确定衰减器设置Measure standards raw data,no correction factors测量标准-原始数据，没有修正因数Attenuator setting is set to force the following:衰减器设置是强制设置如下：Ce

32、rtificate Lumens=SAF*Raw Lumens证明光通量=SAF*原始光通量Note:Raw Lumens=Attenuator Setting*Detector Signal.注意：原始光通量=衰减器设置*探头信号Therefore:Lumens=SAF*Attenuator Setting*Detector signal.因此：光通量=SAF*衰减器设置*探头信号Since we have the SAF,we can set the attenuator setting.一旦我们有了SAF，我们就可以设置衰减器设置了。Measure standards as a test

33、测试时测量标准Measured lumens=SAF*Raw lumens.标准的光通量=SAF*原始光通量Confirm the data matches the certificate assigned value.确认证明赋值的数据匹配28第28页，此课件共40页哦Photometry Systems CalibrationCalibration 1:Detector Based Calibration Luminous Flux Calibration标准1：探头标准-光通量标准(4)Determine Luminous Flux Spectral Correction Factor

34、确定光通量光谱修正因数oThe LMT cell mimics the eye sensitivity curve,but it is never perfect.Therefore,error is introduced.oLMT模仿人眼视觉灵敏度曲线，但是它还不是很完美，所以有误差oThis correction factor is required whenever lamps are measured with different spectra than the initial calibration source.o修正因数要求无论何时测量不同光谱灯管都应和初始校准源比较oA sp

35、ectral correction factor is used so that the attenuator does not have to be reset for lamps with different spectra.o因为运用了光谱修正因数，所以不同光谱的灯衰减器也不用重新调整Determine the SAF for“other”standards(fluorescent,u-bend,etc).确定SAF适合“其它”标准（荧光灯、U形灯等）。Measure standards raw lumen data,no correction factors.测量标准-原始光通数据、无

36、修正因数。Spectral CF=Certificate Lumens/(SAF*raw lumen data).光谱CF=证明光通量/（SAF*原始光通数据）Measure standards as a test测试的测量标准Measured lumens=SAF*SPEC*Raw lumens.测量光通量=SAF*原始光通量Confirm the data matches the certificate assigned value.确认证明赋值的数据匹配29第29页，此课件共40页哦Photometry Systems CalibrationCalibration 1:Detector

37、Based Calibration Luminous Flux Calibration标准1:探头标准-光通量标准(5)Determine Luminous Flux Intensity Distribution Correction Factor(5)确定发光强度分布修正因数oReflector lamps unevenly illuminate the sphere in a different way from the initial standard lamps.This is especially an issue with smaller spheres.o最初的标准灯以不同的方式

38、在球内不均衡的反射.小球的结果尤为特别.oThis correction factor is required whenever lamps are measured with different illumination patterns than the initial standards.o修正因数要求无论何时测量不同光谱灯管都应和初始校准源比较oA intensity distribution correction factor is used so that the attenuator does not have to be reset for lamps with differe

39、nt spectra.o运用亮度分布因数,测试不同光谱灯时衰减器不必重新安装Determine the SAF for“reflector”standards.确定SAF适合“反射标准Measure standards raw lumen data,no correction factors测试标准-原始光通量数据、无修正因数Intensity Distribution CF=Certificate Lumens/(SAF*raw lumen data)亮度分布CF=已证光通量/(SAF*原始光通量数据)30第30页，此课件共40页哦Photometry Systems Calibration

40、Calibration 1:Detector Based Calibration Luminous Flux Calibration(5)Determine Luminous Flux Intensity Distribution Correction Factor(continued)Measure standards as a test检验测量标准Measured lumens=SAF*ID*Raw lumens.标准光通量=SAF*ID*初始光通量Confirm the data matches the certificate assigned value.确定初始数据的证明赋值Cali

41、bration 1:Detector Based Calibration Luminous Flux Calibration标准1:探头标准-光通量标准oOther Corrections Factors can be determined such as positional,etc.o确定其它修正因数如位置等oRemember,this calibration is for Lumens only!There is no need to perform color corrections at the time you perform lumen calibration.o记住这个标准仅适

42、用光通量!当你操作光通量标准时不必进行颜色修正.oThe use of correction factors is dependent upon the lamp type.o使用修正因数取决于灯的型号Measured lumens=SAF*SPEC*ID*Raw lumens.标准光通量=SAF*SPEC*ID*原始光通量31第31页，此课件共40页哦Example-SAF Process32第32页，此课件共40页哦Example Spectral CF Process33第33页，此课件共40页哦Example Lumen Calibration ProcessNONote:only s

43、hows a few correction factors SAF and Spectral CF.34第34页，此课件共40页哦Lumen Calibration Process Contd35第35页，此课件共40页哦Photometry Systems CalibrationCalibration 2:Spectral Based Calibration Spectral Power Distribution Calibration标准2:光谱标准-光谱能量分布标准Spectral Power Distribution光谱能量分布Used to calculate CCT,CRI,x,y

44、,all R-values习惯用于计算CCT,CRI,X,Y,所有R值x,y correction factors are dependent upon this calibration,NOT the luminous flux calibration.X、y修正因数由这个标准决定,不是光通量标准.CCT is directly calculated from x,y,so this must be correct for the CCT to be correct.CCT是从x、y中直接计算出来,所以必须给CCT做正确的校正.Calibrate with a Spectral Flux S

45、tandard.校准光谱流量标准Units are in W/nm 单位(1)A file with data for the standard lamp is compared with the raw measured data.(2)比较标准灯的档案资料数据与原始测量数据Carefully place the Spectral Flux Standard into the sphere.小心地将光谱流量标准放进球内Operate the lamp according to the certificate for the standard.按照标准说明书安装灯36第36页，此课件共40页哦

46、Photometry Systems CalibrationCalibration 2:Spectral Based Calibration Spectral Power Distribution Calibration标准2:光谱标准-光谱能量分布标准(3)Use appropriate software to measure the Spectral Flux Standard.(3)用合适的如件来测量光谱流量标准The software will generate a calibration file by comparing the spectral flux standard fil

47、e with the measured file,wavelength by wavelength.通过比较光谱流量标准文件和测试文件,软件会产生一个标准文件Each data point at each wavelength in the calibration file is calculated according to:每个波长里的每个数据点在标准文件内计算公式如下CAL=标准文件数据/原始探测数据CAL=(Standard File Data)/(Raw Detector Data).The calibration file is used to convert raw detect

48、or data to measured data by:标准文件用于将原始探测数据转变成测量数据:标准SPD=CAL*原始探测数据Measured SPD=CAL*(Raw Detector Data).(4)Measure the Standard as a test and compare the measured SPD with the Spectral Flux Standard File.(4)检验测量标准,比较测量SPD与光谱流量标准档案37第37页，此课件共40页哦Photometry Systems CalibrationoSpectral calibration must

49、be performed when:o必须执行光谱标准New equipment or sphere modifications are performed(painting,New spectrometer,etc)新设备或者球更改(着色,新分光计等)Whenever a color issue is suspected无论何时对色参数有怀疑Note:It is good practice to have a set of color check lamps that are read each month.注意:每个月检查一组颜色对比灯是一个好的习惯.oSpectral calibrati

50、on does not need to be performed when recalibrating for luminous flux unless you suspect that there has been a sphere condition change(large sections of paint flaked off,the baffle shifted,etc).o光通量重新校准光谱标准不需要执行除非你怀疑球条件已经有变动(大块掉漆,移动困难等)38第38页，此课件共40页哦Photometry Best PracticesUse lumen check lamp使用光通