2022年机械制造专业英语课后翻译标准答案.docx

《2022年机械制造专业英语课后翻译标准答案.docx》由会员分享，可在线阅读，更多相关《2022年机械制造专业英语课后翻译标准答案.docx（16页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选学习资料 - - - - - - - - - 第一单元 应力与应变 That branch of scientific analysis which motions, times and forces is called mechanics and is made up of two parts, statics and dynamics. 讨论位移、时间和力运动乘力是科学分析法的一个分歧,被称作力学,力学由两大部 分组成, 静力学 和动力学；For example, if the force operating on a sleeve bearing becomes too high,

2、it will squeeze out the oil film and cause metal-to-metal contact, overheating and rapid failure of the bearing. 例如：假如止推轴承上的作用力过大的话,会挤出油膜,引起金属和金属之间的相互接 触,轴承将过热而快速失效；Our intuitive concept of force includes such ideas as place of application, direction, and magnitude, and these are called the characte

3、ristics of a force. 力的直观概念包括力的作用点、大小、方向,这些被称为力的三 要素 ；All bodies are either elastic or plastic and will be deformed if acted upon by forces. When the deformation of such bodies is small, they are frequently assumed to be rigid, i.e., incapable of deformation, in order to simplify the analysis. 全部的物体既

4、可以是 弹性 的也可以是 塑性 的,假如受到力的作用就产生变形；当变形很小的时候它们被假设成 刚体 ,也就是不产生变形 ,以此来简化分析；The rigid-body assumption cannot be used in internal stresses and strains due to the applied forces to be analyzed. Thus we consider the body to be capable of deforming. 刚体假设不能应用于内应力和内应变的分析,所以在实际力的分析时,要考虑物体的形 变；If all the forces ac

5、ting on a particle are balanced, the particle will either remain at rest or will continue to move in a straight line at a uniform velocity. 假如作用在质点上全部的力是平稳的,质点将会保持静止或做做匀速直线运动；其次单元 材料的强度与塑性A tensile test consists of slowly pulling a sample of material with a tensile load until it breaks. The ends of

6、tensile specimens are usually enlarged to provide extra area for grip-ping and to avoid having the sample break where it is being gripped. 拉伸 试验包括渐渐加载拉伸载荷直到断裂；拉伸试件两端加粗为了供应装夹区域和防止试 件断裂；The usual manner of conducting the test is to deform the specimen at a constant speed. For example, in the universal

7、 testing machines, the motion between the fixed and moving crossheads can be controlled at a constant speed. 通常进行试验的方法就是使试件以恒定速度发生变形；例如,在万能拉伸试验机上,固定 端和移动的十字滑块之间的变形是以恒定速度进行的；The load that must be applied to enforce this displacement rate varies as the test proceeds. This load F may be divided by the

8、cross-sectional area A to obtain the stress in the specimen at any time during the test. 随着试验的进行,用来产生位移的载荷是随位移的变化而变化；在试验中,载荷 F 除以横 截面积 A 可以得到任意时刻点的应力；However actual measurement of L is preferable where this is feasible. Stress and strain based on the initial undeformed dimensions, Ai and Li, are cal

9、led engineering stress and strain. 名师归纳总结 - - - - - - -第 1 页,共 8 页精选学习资料 - - - - - - - - - 然而,在可行的位置上 L的实际测量是更可取的,基于原始 尺寸 Ai 和 Li 的应力和应变称为工程应力和工程应变；Ductile and brittle materials behave differently in compression test as well. The compression test is conducted on short cylindrical specimens placed be

10、tween parallel plates. 塑性和脆性 材料在压缩试验中表现的特性是不相同的；压缩试验是把短圆柱形试件放在两 平行平板之间进行的；The compression test diagram for these materials retains the qualitative features of the tension test diagram. The ultimate compressive strength of a brittle material is determined in the same way as in tension. 材料 压缩 试验 图 保持了

11、拉伸试验图性能上的特点；脆性材料的最大压缩强度与最大拉伸强 度得到的方法相同；第三单元 轴设计Virtually all machines contain shafts. The most common shape for shafts is circular and the cross section can be either solid or hollow hollow shafts can result in weight savings. 几乎全部的机器都有轴 ,最常用的外形是圆形的,横截面是空心 的或实心的圆形截面（空心轴可以削减重量）；A shaft must have adeq

12、uate torsional strength to transmit torque and not be overstressed. It must also be torsionally still enough so that one mounted component does not deviate excessively from its original angular position relative to a second component mounted on the same shaft. 一个轴必需有足够的 扭转 强度来传递扭矩而不会破坏,同样也必需有足够的扭转刚度

13、,这 样安装轴就不能过度偏离相对于安装在同一轴上其次个零件的原始位置；Shafts are mounted on bearings and transmit power through such devices as gears, pulleys, cams and clutches. These devices introduce forces which attempt to bend the shaft ； hence, the shaft must be rigid enough to prevent overloading of the supporting bearings. 轴安

14、装在轴承上通过 齿轮 ,滑轮 ,凸轮 和离合器 这些装置传递力；这些装置可以产生使轴 弯曲 的力,所以轴必修有足够的刚性防止支撑轴承的过载；In addition, the shaft must be able to sustain a combination of bending and torsion and bending. 另外,轴必需能承载弯扭组合的载荷,因此,这样就必需考虑弯扭组合的等效载荷；Components such as gears and pulleys are mounted on shafts by means of key. The design of the ke

15、y and the corresponding keyway in the shaft must be properly evaluated. 齿轮和滑轮构件是用键的方式连接在轴上的,键和对应的 键槽 的设计必需进行估算；Another important aspect of shaft design is the method of directly connecting one shaft to another. This is accomplished by devices such as rigid and flexible couplings. 轴设计的另一个重要方面是直接连接两轴,

16、通过刚性和柔性的联轴器装置来实现；第四单元 Spur Gears齿轮 Pressure angles for spur gears are usually 14.5 or 20 degrees, although other values can be used. Meshing gears must have the same pressure angles. 直齿轮 的压力角通常为 14.5 或 20,另外也使用其它的角度,啮合齿轮必需具有相同的压 力角；The shape of the space between gear teeth on the gear as well as too

17、th module, so most gear 名师归纳总结 - - - - - - -第 2 页,共 8 页精选学习资料 - - - - - - - - - manufacturing methods generate the tooth flank instead of forming. 齿轮轮齿之间齿槽的外形是复杂的,并且随着齿的数目和模数变化而变化,因此大多数齿轮的加工方法是展成齿腹齿廓而不是齿形成形加工；Worm gears are used where high ratios are desired and where the shafts are nonintersecting

18、and at right angles. 蜗杆蜗轮 应用于传动比大而且两轴不相交但相互垂直的情形下；It has the great advantage that the cutting tool is a simple rack with nearly straight sided teeth which can easily be ground accurately. 这种方法有很大的优势,切削工具是一个简洁的带有直齿边的齿条Modern shapers cutting car gears can run at 2000 cutting per minute. The shape of t

19、he cutter is roughly the same as aninvolutegear but the tips of the teeth are rounded. 现代切削汽车的成型器齿轮转速可达每分钟2000 转,齿刀外形与渐开线 大致相同,但齿顶是圆形的；Bevel gears are often used when two shafts are at right angles to each other and their centerline extensions intersect； however, some bevel gears are at angles other

20、 than 90 degrees.圆锥齿轮 一般应用于 相互垂直的 两轴或两个中心线延长线的相交轴中,也可用于不垂直的两轴中；第五单元 cams 凸轮The purpose of any cam is to produce a displacement of its follower ； a secondary follower is often used to produce additional displacement in another location. 使用凸轮的目的是使 从动件 产生位移,次级从动件在另一位置产生附加运动；The relative vertical positi

21、on of point A with respect to B needs to be raised if the reaction value at B is excessive. 假如 B 点的作用力过大,A 点相对 B 点的相对垂直位置必需被提高；In general, the follower is considered to be the part that comes in contact with the cam profile. However, when a secondary follower is used, the motion of the secondary fol

22、lower is dictated by that of the primary follower. 总的来说,从动件是与凸轮轮廓相接触的零件,然而,当用次级从动件时,次级从动件的运动就需通过主要从动件来实现；The simplest type of follower is the reciprocating type that merely moves up and down or in and out with the rotation of the cam centerline or offset form it. ； the centerline can be either colli

23、near with the cam 最简洁的从动件就是随着凸轮的转动而仅做上下（或进出）运动的从动件,其中心线可与 凸轮中心共线,也可与之偏离；Fasteners are devices which permit one part to be joined to a second part and, hence, they are involved in almost all designs. 紧固件 是一种连接一个部分和另一个部分的装置,因此,它涉及到几乎全部的设计；Springs are mechanical members which are designed to give a rel

24、atively large amount of elastic deflection under the action of an externally applied load. 弹簧 是一种被设计于在外力作用下产生相对弹性变形较大的机械构件第七章：砂型铸造名师归纳总结 - - - - - - -第 3 页,共 8 页精选学习资料 - - - - - - - - - 1.The first stage in the production of sand casting must be the design and manufacture of a suitable pattern. Cast

25、ing pattern has to be made larger than the finished casting size to allow for the shrinkage that takes place during solidification and cooling. 在型砂铸造生产中,第一阶段是必需设计和制造合适的 间产生的收缩铸件模型的尺寸要比铸件的尺寸大；模型 ,考虑到铸件在凝固和冷却期2.If a hollow casting is to be made the pattern will include extension pieces so that spaces

26、to accept the sand core are molded into the sand. These additional spaces in the mold are termed core prints. 假如铸造空心铸件时模型上包含伸长杆便于在砂中放置砂芯的空间称为 型芯座 ； 3.Sand molds for the production of small and medium-sized castings are made in a molding box. The mold is made in two or more parts in order that the pa

27、ttern may be removed. 中小型尺寸的铸件砂型是在一个砂箱中制造,砂型由两部分或更多部分组成,以利于模型 的顺当取出； 4.This process of filling and ramming may be done by hand but mold production is automated in a large foundry with the mold boxes moving along a conveyor, firstly to be filled with sand from hoppers and then to pass under mechanica

28、l hammers for ramming.填充和夯实 的过程可以手工完成,但在大型铸造中砂型的制造是自动完成的,砂箱随着传 送带移动,第一被料斗中的砂子填满,然后通过机械锤时被打实；5.The risers should coincide with the highest points of the mold cavity so that the displaced air can readily escape from the mold. The sizes of risers should be such that the metal in them does not freeze to

29、o rapidly. 冒口 应当与型腔的最高点相连接,使得进入的空气可以简洁的从模型中溢出,冒口的尺寸 应当足够大使模型中金属不会太快凝固；6.When the metal that has been poured into a sand mold has fully solidified, the mold is broken and the casting is removed. The casting still has the runner and risers attached to it and there will be sand adhering to portions of

30、the surface. 当熔的金属被倾倒到砂型内并充分凝固以后,砂型将被打破取出铸件,铸件上依旧带有 横 浇口和冒口 并且依旧有砂子粘在表面；造是自动完成的,砂箱随着传送带移动,第一被料 斗中的砂子填满,然后通过机械锤时被打实；第 8 课锻造 1. Forging means the shaping of metal by a series of hammer blows, or by slow application of pressure. The simplest example is a blacksmiths forging of a hot piece of metal by h

31、ammering the work-piece on an anvil. 铸造 是通过一系列的锤打或是在缓慢的加载压力的场合使金属成型的一种方法,最简洁的 实例就是热的金属的 自由锻 ,即通过铁砧上锤打锻件；2. Heavy smiths forging is fundamentally similar, differing only in the scale of the operation. The work-piece may be an ingot of 100 tons and the deforming force provided by a massive forging ham

32、mer, but the whole process is controlled by the master smith, who decides each time where, and with what force, the blow should take place. 重型自由锻和自由锻基本相像,仅在操作的规模上有所不同,锻件可以是一个 100 吨的铁 块,锻压力由一个庞大的锻锤供应,但是整个锻造过程由操作者掌握；他来打算什么时候 用多大力打到什么地方；3. Forging operations may be carried out using either forging hamm

33、ers or forging presses. 名师归纳总结 - - - - - - -第 4 页,共 8 页精选学习资料 - - - - - - - - - With a press, as opposed to a hammer, pressure is slowly applied and plastic deformation tends to occur fairly uniformly throughout the material. 锻造操作者既可以用锻锤也可以用锻压力来实现操作,用锻压力和锻锤相反,在压力缓慢 作用使整个匀称杆产生塑性变形的趋势；4. Forging hamme

34、rs are of two basic types with the large hammer either dropping on to the work-piece accelerated by gravity alone or, as in the steam hammer, accelerated by both gravity and steam pressure. 锻锤 有两种基本类型,既可以用很大的锤子通过作用在工件上也可以用蒸汽压力作用在工 件上或者是两者结合；5. Smiths or open-die forging is used for making very large

35、 forgings or when the number of forgings of a particular design is small. Open-die forging is also used to preform metal prior to final shaping by means of closed-die forging. 自由锻或 开模锻 用于制造大型的锻件或者特别设计的小锻件,开模锻用于预成型金属,在 最终金属成型之前通常使用 闭模锻；6. Closed-die forging involves the use of accurately machined die

36、 blocks. The capital cost of a pair of die blocks is high, but this is allowable when it is required to make forgings to close dimensional tolerances and in large quantity, as would be the case for, say, connecting rods for the engine of a popular car. 闭模锻包括精确的机械加工的模具,一对模具的成本很高,但是只适用于大批量生产和小 的公差要求的锻

37、件,例如,汽车发动机的连杆就是一个典型的例子；第九章电弧焊 1.Arc welding in one form or another is the most widely used form of welding .the electricalsupply is low voltage but high amperage and may be either alternating or direct . 电弧焊在一种或另一种形式是应用最广泛的焊接形式；电力供应是低 并且可以是 沟通 或 直流 ；电压 ,但是大 电流 ,2.the earliest forms of arc welding us

38、ed carbon electrodes.but nowadays the arc is struck between a metal electrode and workpiece .the electrode may either be of tungsten or be a consumable metal electrode that melts ,acting as a source of filler metal . 电弧焊接的最早的形式使用碳电极,但现在的电弧触发一个金属电极与工件之间,电极可 以是钨或可熔化,作为填充金属供源的消耗性金属电极；3.an alternating-c

39、urrent arc is broken and re-established at each half cycle and this leads to arc instability although the use of arc-established agents in the flux coating of electrode wires can overcome this problem . 沟通电弧被打破并且重新建立在每个半周期,这导致电弧不稳固虽然在电极布线 焊剂涂层 使用电弧建立剂可以克服这个问题；4.uncoated welding rods can be used for

40、arc wilding .but it is more usual to use flux-coated electrodes .when steels are welded using uncoated electrodes,oxides and nitrides can form and remain in the weld with a consequent loss of toughness . 未涂覆的焊条可以用于 电弧焊 ；但更通常使用的焊剂涂覆的电极；当钢在使用未涂覆的电极焊接, 氧化物和氮化物 能够形成并保持在焊缝韧性因此而丢失；5.flux-coated electrodes

41、 are widely used .the composition of the coatings is complex and a variety of different coatings are used to cater for different types of welding application . 焊剂涂覆的电极被广泛使用；涂层的组成是复杂和各种不同的涂料是用于协作不同类型的名师归纳总结 - - - - - - -第 5 页,共 8 页精选学习资料 - - - - - - - - - 焊接应用；6.in this case the electron flow is from

42、 electrode to work-piece .A concentrated arc issues from the electrode tip and heating of the work-piece is largely confined to the very small ares beneath the electrode . 在这种情形下 电子 流淌是从电极到工件,从电极头和工件的加热浓缩的弧的问题在很大程 度上仅限于电极下方的特别小顷；第十章：钢1.In simple terms, a plain carbon steel may be said to be an alloy

43、 of iron and carbon containing less than 1.7% carbon. In practice, however, these steels rarely contain more than 1.4% carbon and other elements are also present, either as deliberate additions e. g. manganese or as impurities e. g. sulphur and phosphorus. 简洁来说, 一般碳素钢 也被称为含碳量少于1.7%的合金钢；然而事实上,这些钢材中很少

44、有含碳量多于1.4%,同时也含有其它元素,例如一些额外添加物（如锰）或者杂质 （如硫和磷）；2.In the manufacture of this material, complete deoxidation is not carried out and it is made as rimming steel. It is produced as hot and cold worded sheet, strip, rod, wire and tube, and is available in the hot-worked or process annealed condition. 在材料的

45、生产加工中,不能实现脱氧仍原反应的钢被称为沸腾钢；它被用来生产热处理或 冷处理的 薄片、带、棒、电线、和管,并且它适用 热轧 和退火 的情形下；3.The strength and hardness of these steel is low, but a hard surface can be obtained by carbursing in order to combine a wear-resistant surface with tough core properties. 钢的强度和硬度低,可以通过 性；渗碳 的方法获得表面硬化以达到表面耐寒内部韧性较好的特4.As the car

46、bon content is raised above 0.2%, the strength increases into the range required for constructional purposes, but the ductility decreases. The fabrication qualities working and welding characteristics of this material are very good. 一旦钢中含碳量上升超过 0.2%,结构上的强度会发生庞大变化,但是其延展性会下降；材 料的制造质量（承载和焊接特性）特别好；5.Med

47、ium carbon steels are often quenched-hardened and fully tempered to give good strength with maximum toughness, which are the properties required of components such as shafts, gears and connecting rods. 中碳钢常被淬火硬化和高温回火处理以便赐予良好的温度和最大的韧性,这些是轴、齿轮和连杆所要求的才能特性；6.High carbon steels are quench hardened and li

48、ghtly tempered to give high hardness with only limited toughness. Material in this classification is mainly used for making fairly small, relatively inexpensive cutting tools so that the group as a whole is known as carbon tool steel. 高碳钢常被淬火硬化和低温回火处理以便赐予高硬度和肯定韧性；此类材料主要被用于生 产相当小、牢靠地、廉价的切削工具,者这就是碳素工具钢；第十一章：金属热加工1.The principal ki