PCB专业术语.doc

《PCB专业术语.doc》由会员分享，可在线阅读，更多相关《PCB专业术语.doc（15页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、PCB专业术语PCB Jargon (PCB专业术语)AAbsorption 吸收、吸入Accelerated Test（Aging） 加速试验、加速老化Accelerator 加速剂、速化剂Accept/Acceptance 允收Acceptable Quality Level（AQL） 允收品质水准Accuracy 准确度ACF：Adhesive copper foil 有胶铜箔Activator 活化剂、添加剂比称为ActivatorActive parts（Devices） 主动零件，指积体电路或电晶体Addition Agent 添加剂Additive Process 加成法、分全加

2、成、半加成及部份加成Adhesion 附著力Adhesive 胶类或接著剂Aging 老化Air Knife 风刀Ambient Temperature 环境温度Ampere 安培Amp-Hour 安培小时Annular Ring 孔环Anode 阳极Anode Bag 阳极带ANSI: American National Standard Institute 美国标准协会Anti-Forming Agent 消泡剂AOI: Automatic Optical Inspection 自动光学检验Aperture 开口APQP: Advanced Product Quality Plan Arr

3、ay 排列、阵列Artwork 底片ASIC: Application Specific Integrated Circuit 特定用途的积体电路器Aspect Ratio 纵横比、板厚与孔径之比值Assembly 装配、组装ATE: Automatic Testing Equipment 自动电测设备AVL: Approved Vender List 合格供应商BBack Light（Back Lighting） 背光法Back-UP 垫板Backpanels/ Backplanes 背板、支持板，厚度较厚，Ball Grid Array（BGA） 球脚车列（封装）Barrel 孔壁Base

4、 Material 基材Batch 批（同时间发料某一数量的板子）Bevelling 切斜边Binder 黏结剂Black oxide 黑氧化层，另有棕氧化（Brown Oxide）Blind Via Hole 盲导孔Blister 局部性分层或起泡Blockout 封网，网板之空网处以水溶胶涂满Blow Hole 吹孔，PTH孔壁有破洞（void）所造成Boiler (Water Tube Boiler/ Fire Tube Boiler)BOM: Bill of Material 用料表Bond Strength 结合强度Bonding Sheet(Layer) 接合片、接著层，指PPBo

5、nding Wire 结合线，IC之晶片与PCB之引线Bow 板弯Break-away Panel 可断开板或者说Break Away TabBreak Point 出像点、影像点Break-Out 破出（钻孔破出开成断环情形）Bridging 搭桥、桥接Brightener 光泽剂Brush Plating 刷镀BTU/British Thermal Unit 英制热量单位Bump 突块Buried Via Hole 埋导孔Burn-in 高温加速老化试验Burning 烧焦Burr 毛头Buy-off 认可CCAD: Computer Aided Design 电脑辅助设计CAM: Com

6、puter Aided Manufacturing 电脑辅助制造CAT: Computer Aided Testing 电脑辅助测试Capacitance 电容Carbide 碳化物、碳化钨钻头CAR: Corrective Action Report 改善报告Carbon Treatment 活性碳处理Card 卡板Carrier 载体Cartridge 滤芯Cathode 阴极CCL: Copper Clad Laminates 铜箔基板Ceramics 陶瓷Certificate 证明书CFC 氟氯碳化物 Chloro-Fluoro-CarbonChamfer 倒角、去掉直角Charac

7、teristic Impedance 特性阻抗Cheek list 检察清单Chip 晶粒、晶片Chip On Board 晶片黏著板Clean Room 无尘室 (Class 100)Cleanliness 清洁度Clearance 余隙、余环COB（Chip on Board） 晶片在板上直接组装COC（Certificate of Compliance） 出货合格书COF（Chip on Flexible PCB）COG（Chip glass）Coefficient of Thermal Expansion 热膨胀系数（CTE）Cold Solder Joint 冷焊点Component

8、 Hole 零件孔Component Side 组件面、零件面Conditioning 整孔Conductivity 导电度Connector 连接器Continuity Test 连通性试验Copper Foil 铜箔、铜皮Copper Ball 铜球Corner Crack 镀通孔转角断角Cp: Capability of Process 制程能力指数Crack 裂痕Crazing 白斑（基板外观上的缺点）Crosstalk 杂讯、串讯Cure/Curing 硬化、热化Current Density （C.D.）电流密度（1 ASD=9.1 ASF）Curtain Coating 液涂法D

9、Datum 基准点Deburring 去毛头Defect 不良缺点Degreasing 脱脂Delamination 分层、爆板Dent 凹陷、缓和均匀的下陷Desmearing 除胶渣Developer 显像液Deviation 偏差Device 电子元件Dewetting 缩锡DFM: Design for Manufacturing/Dirty foreign Materials 异物、杂质Die 冲模Dielectric 介质Dielectric Constant 介质常数Dimensional Stability 尺度安定性DIP（Dual Inline Package） 双排脚封装

10、体Direct Plating 直接电镀DI Water 纯水 (De-Ionize Water)DOE/Design of Experiment 实验计划法DPPM（Defect Parts Per Million）Drilling 钻孔Drill Bit 钻针Dry Film 干膜Dummy 假镀EECN: Engineering Change Notice 工程变更通知Elongation 延伸性EMI 电磁干扰 Electromagnetic InterferenceENIG: Electroless Nickel Immersion Gold 化镍浸金Entek 有机护铜处理Entr

11、y Material 盖板E.T/Electric Test 电测、电气测试Epoxy Resin 环氧树脂ESD: Electro-Static Discharge 静电流量Etching 蚀刻Etchback 加蚀Etch Factor 蚀刻函数Etching Resist 抗蚀阻剂Expose Copper 漏铜Exposure 曝光Eyelet 铆钉 RivetFFAAR（First Article Approval Report）Failure 故障、损坏Fault 缺陷、瑕疵FCC/Federal Communication Commission 美国联邦通讯委员会Fiber Ex

12、posure 玻织显露Fiducial Mark 基准记号、光学点Film 底片Filter 过滤器Fine Line 细线Finger 手指Finishing 制成品在外观上的最后处理First Article 试产的首件或首批小量产品First Pass-Yield 初检良品率Fixture 夹具、治具 (Rig and Fixture)Flame Resistant 耐燃性（分HB、VO、V1及V2等四级）Flux 助焊剂Foil Burr 铜箔毛边Foot Pint（Land Pattern） 脚垫Foreign Material 外来物、异物FR4/Flame Resistant L

13、aminates 耐燃性积层板材Frequency 频率GGauge 量规Gel Time 胶化时间Gerber Data/Gerber File 格搏档案Glass Fiber 玻璃纤维Glass Fiber Protrusion 玻纤突出Glass Transition Temperature/Tg 玻璃态转化温度Golden Board 测试用标准板Grid 标准格Ground Plane 接地层Guide Pin 导针HHaloing 白圈、白边（在钻孔、开槽等机械动作一旦过猛时将造成内部树脂之破碎或微小分层裂开的现象）Hardener 硬化剂Hardness 硬度Heat Dissi

14、pation 散热Hertz（Hz） 赫芝HEPA/High Efficiency Particulate Air Filter 高效空气尘粒过滤机Hipot Test 高压电测 High Potential TestHit 擎Holding Time 停区时间Hole Block 孔塞Hole Breakout 孔位破出，简称BreakoutHole counter 数孔机Hole Density 孔数密度Hole Pull Strength 孔壁强度Hole Void 破洞Hot Air Levelling 喷锡 HASL/HALTHE(High Temperature Elongatio

15、n) 高温延伸性II.C.Socket 积体电路插座Image Transfer 影像转移IMC: Inter-metallic compound 介面合金共化物Immersion Plating 浸镀Impedance 阻抗In-Circuit Testing 组装板电测，ICTIndexing Hole 基准孔Infrared(IR) 红外线Ink 油墨Inner Layer 内层Input/Output 输入、输出Insert/Insertion 插接、插装Insulation Resistance 绝缘电阻Integrated Circuit (IC) 积体电路器Interconnec

16、tion互连Intermatallic Compound(IMC) 介面合金共化物Internal Stress 内应力Ion Cleanliness 离子清洁度Ionic Contamination 离子污染IPC: The Institute for Interconnecting and Packaging Electronic Circuits 美国印刷电路板协会ISO: International Organization for Standardization 国际标准组织Isolation 隔离性JJPCA/Japan Print Circuit Association 日本印刷

17、电路工业会Just-In-Time(JIT) 适时供应KKeyboard 键盘Kraft Paper 牛皮纸LLaminate(s) 基板、积层板Laminator 压膜机Land 孔环焊垫、独立点Landless Hole 无环通孔Laser Direct Imaging/LDI 雷射直接成像Laser Photoplotter 雷射曝光机、绘图机Lay Out 布线、布局 (configuration, general arrangement)Lay Up 叠合Lead Frame 脚架Lead 引脚、接脚Legend 文字标记Levelling 整平Light Intensity 光强度

18、LMW: License Manufacturing Warehouse 保税厂Lot Size 批量LRR(Lot Reject Rate)MMajor Defect 严重缺点、主要缺点Marking 标记Mask 阻剂Mass Lamination 大型压板MCM/Multi-Chip Module 多晶片模组Measling 白点Membrane Switch 薄膜开关Microctching 微蚀Microsectioning 微切片法Migration迁移Mil 英丝0.001 inmisregistration 对不准、对不准度MLB/Multi-Layer Board 多层板Mo

19、dem 调变及解调器、数据机Modification 修改、改变Module 模组Mother Board 主机板NNail Head 钉头N.C.数值控制（Numerical Control）Negative 负片Negative etch-back 反回蚀Nick 缺口Node 节点Nodule 瘤Non-Conformance 不合格品Non-flammable 非燃性Non-wetting 不沾锡Normal Distribution 常态分配NPI：New project introduction)NRE Charge-Non-Recurring Engineering Charge

20、 不会重收的工程费用OOhm 欧姆Omega Meter 离子污染检测仪Open Circuits 断线Optical Density 光密度Optical Inspection 光学检验Organic Solderability Preservatives(OSP) 有机保焊剂Outgassing 出气、吹气Output 产出、输出Overflow 溢流Oxidation氧化Ozone Depletion 臭氧层耗损PPackaging 封装、购装Packing 包装Pad 配圈、孔环焊垫Panel Plating 全板镀铜Passive Parts 被动零件，如电阻、电容Past 膏（锡膏

21、Solder Paste）Pattern Plating 线路电镀PCB/Printed Circuit Board 印刷电路板Peel Strength 抗撕强度Peripheral 周边附属设备Phototool 底片（一般指偶氮棕片 Diazo Film）Pin Grid Array(PGA) 矩阵式针脚封装Pinhole 针孔Pin 接脚、插梢、插针Pink Ring 粉红圈Pits 凹点（小面积下陷）Pitch 脚距、垫距、线距Plasma 电浆Plated through Hole/PTH 镀通孔Plug 插脚、塞孔Polarization 分极、极化Polyimide(PI) 聚

22、亚酸胺Popcorn Effect 爆米花效应Post Cure 疏孔度试验Power Plane 后续硬化、后烤Power Supply 电源层PPM/Parts Per Million 百万分之几Preheat 预热Prepreg 胶片、树脂片Press Plate 压合钢板Press-Fit Contact 挤入式接触Printing 印刷Probe 探针Profile 轮廓、部面图、升温曲线图积线Punch 横切、冲床QQIT(Quality improvement Team) 品质改善小组Qualified Products List 合格产品（供应者）名单RRadiometer 辐

23、射计、光度计Radius 尺角、半径Reference Dimension 参考尺度、参考尺寸Reflow Soldering 重熔焊接、熔焊Registration 对准度Reject 剔退、拒收Reliability 可靠度、信赖度Repair 修理Resin Content 胶含量、树脂含量Resin Flow 胶流量、树脂流量Resist 阻剂、阻膜Resistor 电阻器、电阻Resolution 解像、解像度、解析度Resolving Power 解析力、解像力（分辨力）Rework(ing) 重工、再加工Ring 套环Roller Cutter 混切机（俗称锯板机）Roller

24、Coating 滚动涂布法Routing 切外型、捞外型RRM: Revolutions per Minute 转速（每分钟）Run-out 偏转、绕转、累积距差SSCAR(Supplier CA Request) 供应商改善报告SCM: Supply chain Management 供应商管理系统Scratch 刮痕Screen Printing 网版印刷Scrubber 磨刷机、磨刷器Selective Plating 选择性电镀SEM/Scanning Electron Microscope 扫瞄式电子显微镜Semi-Conductor 半导体Shearing 剪、裁切Short 短路

25、SIR(Surface Insulation Resistance) 表面绝缘电阻Side Wall 侧壁Sigma(Standard Deviation) 标准差Signal 讯号Silicon 矽Silk Screen 网版印刷、丝网印刷Skin Effect 集肤效应Skip Printing 漏印Slot 槽孔Smear 胶渣SMT/Surface Mount Technology 表面黏装技术Solder 焊锡Solderability 焊锡性Solder Ball 锡球Solder Bridging 锡桥Solder Bump 焊锡凸块Solder Dam 锡堤（IC脚间的防焊）S

26、older Levelling 喷锡、热风整平Solder Mask(S/M) 绿漆、防焊膜Solder Paste 锡膏Solder Plug 锡塞、锡柱Solder Pot 锡炉Solder Side 焊锡面Soldering Fluid/Soldering Oil 助焊液、护焊汕Solid Content 固体含量SOP(Standard Operation Procedure) 标准作业程序Spacing 间距SPC/Statistical Process Control 统计制程管制Specific Gravity SG比重Specification(Spec) 规范、规格Speci

27、men 样品、试样Spindle 钻轴Spray Coating 喷著涂装Stencil 版膜、网版Storage condition 储存条件Stress Relief 消除应力Substrate 底材Surface Insulation Resistance(SIR) 表面绝缘电阻Surface Tenting 表面张力Surface-Mount Device 表面黏装零件Swelling Agents/Sweller 膨胀剂SWR(Special Working Request) 试产前之“特殊工作要求”TTab 接点、金手指Tape 撕胶带试验Teflon 铁氟龙Temperature

28、 Profile 温度曲线Template 模板Tensile Strength 抗拉强度Tenting 盖孔法Terminal 端子Thermal Stress 热应力Thermal Shock 热冲击Thin Copper Foil 薄铜箔Then film Technology 薄膜技术Throwing Power 分布力Tolerance 公差Touch Up 检修（简单的工具在手操作下即可进行的小规范的检修，称之Touch Up或Rewok有些类似）Trace 线路、导线Traceability 追溯性、可溯性Transistor 电晶体Transmission Line 传输线Tw

29、ist 板翘、板扭UUL 保险业试验 Underwriters Laboratories/INCUltra Violet Curing(UV Curing) 紫外线硬化Ultrasonic Cleaning 超音波清洗Undercut/Undercutting 侧蚀Universal Tester 万用型电测机VVacuum Lamination 真空压合Vacuum Packing 真空包装Viscosity 黏滞度、黏度Vision Systems 视觉系统Visual Examination(Inspection) 目视检查Voltage 电压WWafer 晶圆Warp/Warpage

30、板弯Warp and Twist 板弯翘Washer 垫圈Waste Treatment 废弃处理Water Absorption 吸水性Water Break 水膜破散、水破Watermark 水印Wave Soldering 波焊Weave Exposure 织纹显露Weave Texture 织纹隐现Welding 熔接Wet Process 湿式制程Wetting Balance 沾锡、沾湿White Spot 白点Wicking effect 灯芯效应Wire Bonding 打线结合WIP(Working Piece in Process) 在制品XX Axis X轴X-Ray X

31、光YY-Axis Y轴Yield 良品率、良率、产率ZZ-Axis X轴OtherHDI-High Density inter-connect 高密度内连接SWOT Strengths Weaknesses Opportunities Threats CD: Compact DiscCPU: Central Process UnitDLD: Direct Laser Drilling (CO2 Laser, YAG Laser)DVD: Digital Versatile DiscEEPROM: Electrically Erasable Programmable Read Only Memo

32、ryEMS: Electronics Manufacturing ServiceGPS: Global Positioning ServiceHDD: Hard Disk DriveHDTV: High Density TVLCD: Liquid Crystal DisplayLED: Light Emitting DiodeVCD: Video Compact DiskQuality System Requirements QS-9000(質量體系要求)Advanced Product Quality Planning and Control Plan APQP(產品質量先期策劃和控制計劃)

33、Measurement Systems Analysis MSA(測量系統分析)Potential Failure Mode and Effects Analysis FMEA(潜在失效模式與後果分析)Production Part Approval Process PPAP (生產件批准程序)Statistical Process Control SPC (統計過程控制)IPC-A-600Classification 分级Acceptance Criteria 允收规格Applicable Documents 参考资料Dimensions And Tolerances 尺度与公差Terms

34、And Definitions 术语及定义Workmanship 工艺水准Externally Observable Characteristics 外观特性Board Edges 板边Burrs 看头、毛刺Nonmetallic Burrs 非金属性毛头Metallic Burrs 金属毛头Nicks 缺口Haloing 白边Base Material 基材Weave Exposure 织纹显露Weave Texture 织纹隐现Exposed/Disrupted Fibers 玻织曝露/扰乱Pits and Voids 凹点与凹坑Base Material Subsurface 基材次表面

35、Measling白点Crazing白斑Delamination/Blister分层/起泡Foreign Inclusions外来夹杂物Solder Coatings and Fused Tin Lead喷锡板或熔锡板Nonwetting拒锡（不沾锡）Dewetting缩锡Holes-Plated-Through-General镀通孔概要Nodules/Burrs镀瘤/毛头Pink Ring粉红圈Voids-Copper Plating镀铜层破洞Voids-Finished Coating完工皮膜之镀层破洞Lifted Lands-(Visual)孔环浮离（目检）Holes-Unsupporte

36、d未镀孔Haloing白圈Printed Contacts板边接触金手指Surface Plating-General表面镀层通则Surface Plating-Wire Bond Pads打线承垫之表面Burrs on Edge-Board Contacts板边接点之毛头Adhesion of Overplate表面镀层之附着力Marking标记Etched Marking蚀刻标记Screened or Ink Stamped Marking纲印或盖印之标记Solder Resist(Solder Mask)防焊绿漆Coverage Over Conductors (Skip Coverag

37、e)边线表面之覆盖性（覆盖不全、跳印）Registration to Holes (All Finishes)对孔之套准度（各种表处理层）Registration to Other Conductive Patterns其他防焊的对准性Ball Grid Array (Solder Resist-Defined Lands)球脚格列体之焊垫（绿漆设限之焊垫）Ball Grid Array (Copper-Defined Lands)球脚格列体（铜面设限之焊垫）Ball Grid Array (Solder Dam)球脚格列体（防焊堤）Blisters/Delamination起泡/分层Adhe

38、sion(Flaking or Peeling)附著力（破片或剥落）Waves/Wrinkles/Ripples起浪/起皱/纹路Tenting(Via Holes)盖孔（导通孔、过孔）Pattern Definition-Dimensional圆形尺度特性Conductor Width and Spacing线宽与间距Conductor Width线宽Conductor Spacing导线间距External Annular Ring-Measurement孔环测量External Annular Ring-Supported Holes有孔壁支援的外孔环External Annular Ri

39、ng-Unsupported Holes无孔壁支援的外孔环Flatness平坦度Internally Observable Characteristics可观察到的内在特性Dielectric Materials介质材料Laminate Voids(Outside Thermal Zone)压板空洞（或热区之外）Registration/Conductors to Holes导体与通孔之间的对准度Clearance Hole/Unsupported/to Power/Ground Planes针对电源层或接地层具隔环之非镀通孔Delamination/Blister分层/起泡Etchback回

40、蚀Negative Etchback反回蚀Smear Removal除胶渣Dielectric Material/Clearance/Metal Plane for Supported Holes金属层与通孔壁之介质隔距Layer-to-Layer Spacing层与层之间距Resin Recession树脂缩陷Conductive Patterns-General导线概论Etching Characteristics蚀刻特性Print and Etch印后即蚀刻（指正片法）Surface Conductor Thickness(Foil Plus Plating)表导体厚度（铜箔加电镀铜）F

41、oil Thickness-Internal Layers内层箔厚Plated-Through Holes-General镀通孔概论Annular Ring-Internal Layers各内层之孔环Lifted Lands-(Cross-Sections)焊环浮起（切片上所见）Foil Crack-(Internal Foil)“C”Crack内层铜箔之裂纹Foil Crack-(External Foil)镀层破裂Plating Crack-(Barrel)“E”Crack孔壁镀层破裂Plating Crack-(Corner)“F”Crack孔角镀层破裂Plating Nodules镀层

42、长瘤Copper Plating Thickness-Hole Wall孔壁镀铜厚度Plating Voids镀层破洞Solder Coating Thickness (Only When Specified)焊锡皮膜厚度（当已规定检查者）Solder Resist Thickness绿漆厚度Wicking灯芯效应（指玻织束渗入化学铜）Wicking/Clearance Holes隔离孔之渗铜Innerlayer Separation-Vertical (Axial) Microsection内层（环）分离-垂直（纵断面）微切片Innerlayer Separation-Horizontal

43、(Transverse) Microsection内层（环）分离-水平（横断面）微切片Material Fill of Blind and Buried Vias盲孔与埋孔之填充材料钻孔式镀通孔Plated-Through Holes-Drilled钻孔式镀通孔Burrs毛头Nailheading钉头Plated-Through Holes-Punched冲孔式镀通孔Roughness and Nodules粗糙与镀瘤Flare喇叭口Miscellaneous其他离顶Flexible And Rigid-Flex Printed Wiring软性及软硬合板Metal Core Printed

44、Boards金属平心电路板Type Classifications型式分类Spacing Laminated Type间距压合板Insulation Thickness/Insulated Metal Substrate已绝缘金属底材之绝缘厚度Insulation Material Fill/Laminated Type Metal Core压合型金属平心之绝缘填料Cracks in Insulation Material Fill/Laminated Type压合型绝缘填充料之裂纹Core Bond to Plated-Through Hole Wall平心层与镀通孔之间的固著Flush Printed Boards表面全平板Flushness of Surface Conductor表面导线之平坦性Cleanliness Testing清洁度试验Solderability Testing焊锡性试验Plated-Through Holes镀通孔Electrical Integrity电性之完整Page 15 Of 15