电路分析与电子线路综合训练题（DOC43页）.doc

《电路分析与电子线路综合训练题（DOC43页）.doc》由会员分享，可在线阅读，更多相关《电路分析与电子线路综合训练题（DOC43页）.doc（43页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、2022年-2023年建筑工程管理行业文档 齐鲁斌创作2018年电路分析与电子线路综合训练题注意：2018年电路分析与电子线路综合训练组队共同讨论完成综合训练题目3-4题，以书面形式撰写报告，需要详细的讨论过程和仿真的结果。请同学们自学“数值分析软件（如MATLAB等）及电路仿真软件（如Multisim或Pspice等）”。提交书面报告时间：6月20日前。Project 1Power SuppliesObjective: This project will show some of the basic principles of power supplies using fullwave re

2、ctifier, Zener diode, and fixed-voltage regulator circuits.Components: Bridge Rectifier (50 PIV, 1 A), Zener diode (10 V at 500 mW), 7805 regulatorIntroduction:Most of the direct current (DC) power used in electronic devices is derived by converting 60 Hz, 115 V alternating current (AC) power to dir

3、ect current power. This AC to DC conversion usually involves a step-down transformer, rectifier, filter, and a regulator. The step-down transformer is used to decrease the AC line voltage from 115 VRMS to an RMS value near the DC voltage needed. The output of the step-down transformer is then fed in

4、to a diode rectifier circuit that only outputs positive halves of the input sinusoid. A filter is then used to smooth the rectifier output to achieve a nearly constant DC voltage level. A regulator can be added after the filter to ensure a constant output voltage in spite of changes in load current

5、and input voltages.Two different types of voltage regulators will be used in this project. The first involves a Zener diode circuit and the second involves a voltage regulator circuit. A Zener diode can be used as a voltage regulator when the diode is reverse biased and operated in the breakdown reg

6、ion. To maintain voltage regulation, the Zener diode must be operated in the breakdown region at a current greater than the knee current (IZK). For currents greater than IZK, the Zener diode characteristic curve is nearly vertical and the voltage across the diode changes very little. Of course there

7、 is a maximum current the diode can tolerate, so good regulation is provided when the diode is reverse biased with currents between IZK and IZMAX. Zener diodes are available with a wide variety of breakdown voltages. Another type of voltage regulator is available with the 7800 series regulators. Thi

8、s series of fixed-voltage regulators is numbered 78xx, where xx corresponds to the value of the output voltage. Output voltages from 5 to 24 volts are available. These regulators are easy to use and work very well.Design:1. Find approximations for the DC voltage level and AC peak to peak ripple volt

9、age for the bridge rectifier and filter circuit of Figure 1-1.2. For the Zener diode regulator circuit of Figure 1-2 assume that the Zener diode will regulate at 10 V over a current range of 5 mA to 25 mA. Assuming that the current flowing through R is always between 5 mA and 25 mA and the Zener dio

10、de is regulating at 10 V, find the minimum values of R and RL required. You may assume the forward diode drop for the two diodes is 1 V.Lab Procedure:1. Construct the bridge rectifier circuit of Figure 1-1 without the capacitor. Use the Variac with the step-down transformer for the input voltage to

11、the bridge rectifier. With the transformer plugged into the Variac, adjust the Variac until the secondary voltage from the transformer equals 12 VRMS. BE CAREFUL not to short the secondary terminals! Observe the secondary waveform on the oscilloscope. Put the oscilloscope on DC coupling and observe

12、the load voltage waveform VL. Remember that both the input source and the load cannot share a common ground terminal.2. Remove power from the circuit. Insert the capacitor as shown in Figure 1-1 being sure to observe the correct polarity. Energize the circuit. With the oscilloscope on DC coupling ob

13、serve VL. Measure the DC voltage level using the digital voltmeter. With the oscilloscope on AC coupling observe the ripple voltage VR. Compare these measured values with the calculated values.3. Observe the effect of loading on the circuit by changing the load resistor from 1 kW to 500 W. Measure t

14、he DC voltage level with the digital voltmeter. Observe the ripple voltage with the oscilloscope set on AC coupling. Compare these values with the previously recorded values.4. Record the Zener diode characteristic curve from the digital curve tracer. Note the value of the breakdown voltage in the b

15、reakdown region. Also note the value of the knee current IZK.5. After verifying your designed values for R and RL with the instructor, construct the Zener diode regulator circuit of Figure 1-2. Measure the DC voltage level with the digital voltmeter for the minimum value of RL along with several val

16、ues above and below the minimum value. Be careful not to overload the Zener diode. Comment on the circuits operation for these different load resistances.6. Construct the 7805 regulator circuit of Figure 1-3 being careful to observe the correct pin configuration of the regulator. Measure the load vo

17、ltage for RL equal to 300 W, 200 W, and 100 W. Calculate the current for each of these cases. Does the value of the load resistor affect the output voltage?7. Using RL equal to 200 W, record the 7805 regulator input voltage (pin 1) and output voltage (pin 3). Decrease the regulator input voltage by

18、decreasing the setting of the Variac. For each decrease in amplitude, record the regulator input and output voltages. Continue decreasing the amplitude until the output of the regulator drops a measurable amount below 5 V. What is the minimum input voltage needed for the 7805 regulator to produce a

19、5 V output?Questions:1. Why cant the input source and load have a common ground in the bridge rectifier circuit?2. Can the Zener diode be used as a conventional diode? Explain your answer and verify with a curve from the curve tracer.3. Would the value of the output filter capacitor have to increase

20、, decrease, or remain the same to maintain the same ripple voltage if the bridge rectifier were changed to a half-wave rectifier? Explain your answer.4. How would increasing the frequency of the input source affect the ripple voltage assuming all components remained the same?Project 2Analog Applicat

21、ions of the Operational AmplifierObjective: This project will demonstrate some of the analog applications of an operational amplifier through a summing circuit and a bandpass filter circuit.Components: 741 op-ampIntroduction:Figure 2-1 shows a weighted summer circuit in the inverting configuration.

22、This circuit can be used to sum individual input signals with a variable gain for each signal. The virtual ground at the inverting input terminal of the op-amp keeps the input signals isolated from each other. This isolation makes it possible for each input to be summed with a different gain.The ban

23、dpass filter shown in Figure 2-2 uses an op-amp in combination with resistors and capacitors. Since the op-amp can increase the gain of the filter, the filter is classified as an active filter. This bandpass filter circuit is extremely useful because the center frequency can be changed by varying a

24、resistor instead of changing the values of the capacitors. The center frequency is given by:The center frequency can be changed by varying the variable resistor R3. Increasing R3 decreases the center frequency while decreasing R3 increases the center frequency. The bandwidth is given by:Notice that

25、the bandwidth is independent of the variable resistor R3 so the center frequency may be varied without changing the value of the bandwidth. The gain at the center frequency of the bandpass filter is given by:Design:1. Find the relationship between the output and inputs for the weighted summer circui

26、t of Figure 2-1.2. Design a bandpass filter with a center frequency of 2.0 kHz and a bandwidth of 200 Hz. Let the voltage gain at the center frequency be 20. Check your design with PSPICE. Use 15 V supplies for the op-amp. Use RL = 2.4 kW.Figure 2 - 1: Weighted SummerFigure 2 - 2: Bandpass FilterLab

27、 Procedure:1. Construct the summing amplifier of Figure 2-1. Design for the transfer function to be VO = -2 VIN1 - VIN2. Use 15 V supplies for the op-amp. Use RL = 2.4 kW.2. Let VIN1 be a 1 V peak sine wave at 1 kHz and VIN2 equal to 5 V DC. Verify the amplifiers operation by monitoring the output w

28、aveform on the oscilloscope.3. Construct the bandpass filter of Figure 2-2. Use the designed values for the resistors and capacitors. Use 15 V supplies for the op-amp. Use RL = 2.4 kW.4. Record and plot the frequency response (you may want to use computer control for the sweep and data collection).

29、Find the center frequency, corner frequencies, bandwidth, and center frequency voltage gain to verify that the specifications have been met.5. Change R3 to lower the center frequency from 2.0 kHz to 1.0 kHz. Repeat part 4 for the new frequency response. Verify that the new center frequency is 1.0 kH

30、z. What is the new bandwidth? What is the new center frequency voltage gain? Compare with the measurements of Procedure 4.Questions:1. Could the summer circuit be used with the inputs connected to the noninverting terminal and produce the same affect without the inversion? Explain.2. What is/are the

31、 benefit(s) of using an op-amp circuit to produce a bandpass filter over using an RLC circuit with a noninverting op-amp at the output of the RLC circuit?Project 3Analog Computer Applications using the Operational AmplifierObjective: This project will focus on the use of the operational amplifier in

32、 performing the mathematical operations of integration and differentiation. The design of a simple circuit (analog computer) to solve a differential equation will also be included.Components: 741 op-ampIntroduction:Figures 3-1 and 3-2 illustrate two op-amp based circuits designed to perform differen

33、tiation and integration respectively. The operations are performed real-time and can be helpful in observing both initial transients and steady state response. The analysis of the circuits is based on the ideal op-amp assumptions and performed in the time domain. The resistor RI shown in the two cir

34、cuits is included to help with stability and for general circuit protection. The value for RI is nominally set equal to the feedback resistor (Figure 3-1) or the input resistor (Figure 3-2). The purpose of the optional resistor is left for student investigation in conjunction with the summary questi

35、ons.The differentiator and integrator circuits may be combined with standard inverting and non-inverting op-amp circuits to provide the building blocks for analog computers. The resultant analog computer circuits are designed to solve differential and/or integral/differential equations in a real tim

36、e environment. The ability to easily include, and change, initial conditions and forcing functions are additional benefits of the analog computers. Figure 3-3 illustrates a circuit designed to solve the second order differential equation KY - Y = 0 with the initial condition Y(0) = - VX and K = R1R2

37、C1C2. The initial condition is set by using the momentary contact switch to force the output to equal the applied voltage at t = 0 (the time the switch is closed). While the major advances in digital computers and digital signal processing have reduced the use of these three circuits, they are still

38、 a fast and relatively inexpensive method for process control and stability/operation analysis for systems that can be represented in terms of differential equations.Design:1. Derive the expressions relating the input and output signals for the circuits shown in Figures 3-1 and 3-2.2. Design an anal

39、og computer to solve with y(0) = 2. Solve the differential equation when f(t) = 0 and verify your results using PSpice.Figure 3 - 1: DifferentiatorFigure 3 - 2: IntegratorFigure 3 - 3: Analog Computer (linear, second order, homogenous differential equation)Lab Procedure:1. Construct the circuit show

40、n in Figure 3-1. Use 15 V supplies for the op-amp and a load resistance of 2.4 kW.2. Verify the operation of the circuit using a 500 mV peak, 50 Hz sinewave as the input signal. Be sure to design the gain such that the output does not saturate.3. Repeat step 2 with a sinewave frequency of 500 Hz. Do

41、es the circuit still operate correctly? What changes need to be made to prevent output saturation?4. Repeat steps 2 and 3 using a triangle wave and then using a square wave with the same magnitudes and frequencies as used in steps 2 and 3. 5. Construct the circuit shown in Figure 3-2. Again, use 15

42、V supplies for the op-amp and a load resistance of 2.4 kW.6. Repeat steps 2 through 4 for this circuit. Be sure to adjust your gain as necessary to maintain an output signal within the saturation limits of 12 V.7. Construct the circuit designed to solve the differential equation in part 2 of the des

43、ign section. Verify the operation of the design using three different input waves (sine, triangle, and square). Determine the operation for at least three different frequencies - 10 Hz, 1 kHz, and 100 kHz. Explain any differences in operation of the circuit. What affect does the initial condition ha

44、ve on the result?Questions:1. How could you use the differentiator to obtain an estimate of the slew rate for the op-amp?2. Why should you include a resistor in parallel with the capacitor in the integrator?3. What is the purpose of the resistor in series with the input capacitor in the differentiat

45、or?4. Is it possible to design a circuit to perform the differentiation and integration functions using the non-inverting input? Explain your answer.Project 4Common Emitter Amplifier(designed for two lab periods)Objective: This project will show how the h-parameters for a BJT can be measured and use

46、d in an equivalent circuit model for the BJT. A CE small signal amplifier will be biased and designed to specifications along with both low and high frequency response and adjustment. Series-series feedback will also be used to control the bandwidth and input impedance of the CE amplifier.Components

47、: 2N2222 BJTIntroduction:In order for circuits involving transistors to be analyzed, the terminal behavior of the transistor must be characterized by a model. Two of the models often used for a BJT are the hybrid-p and the h-parameter models. The complete hybrid-p circuit model for the BJT is shown

48、in Figure 9-1. This model includes the internal capacitances and output resistance of the BJT. Inclusion of the internal transistor capacitances makes the hybrid-p model valid throughout the entire frequency range of the transistor. Typical data sheet values of Cp and Cm are 13 pF and 8 pF respectiv

49、ely. These values are so small that Cp and Cm may be considered open circuits for midband frequencies. The resistance rx typically has a value in the tens of ohms and can be considered a short circuit while rm and ro are usually extremely large in value and can be considered open circuits. The h-parameter small signal model for the BJT is charac