基于单片机的智能晾衣架控制系统的设计与实现外文文献原稿和译文(共20页).docx

《基于单片机的智能晾衣架控制系统的设计与实现外文文献原稿和译文(共20页).docx》由会员分享，可在线阅读，更多相关《基于单片机的智能晾衣架控制系统的设计与实现外文文献原稿和译文(共20页).docx（20页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上外文文献原稿和译文原稿The Description of AT89S511 General DescriptionThe AT89S51 is a low-power, high-performance CMOS 8-bit microcontroller with 4K bytes of In-System Programmable Flash memory. The device is manufactured using Atmels high-density nonvolatile memory technology and is compatible wi

2、th the industry-standard 80C51 instruction set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with In-System Programmable Flash on a monolithic chip, the Atmel AT89S51 is a po

3、werful microcontroller which provides a highly-flexible and cost-effective solution to many embedded control applications.The AT89S51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, Watchdog timer, two data pointers, two 16-bit timer/counters, a five-vect

4、or two-level interrupt architecture, a full duplex serial port, on-chip oscillator, and clock circuitry. In addition, the AT89S51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the

5、 RAM, timer/counters, serial port, and interrupt system to continue functioning. The Power-down mode saves the RAM contents but freezes the oscillator, disabling all other chip functions until the next external interrupt or hardware reset.2 PortsPort 0 is an 8-bit open drain bi-directional I/O port.

6、 As an output port, each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as high-impedance inputs. Port 0 can also be configured to be the multiplexed low-order address/data bus during accesses to external program and data memory. In this mode, P0 has internal

7、 pull-ups. Port 0 also receives the code bytes during Flash programming and outputs the code bytes during program verification. External pull-ups are required during program verification.Port 1 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 1 output buffers can sink/source four

8、 TTL inputs. When 1s are written to Port 1 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups. Port 1 also receives the low-order address bytes during Fl

9、ash programming and verification.Port PinAlternate FunctionsP1.5MOSI (used for In-System Programming)P1.6MOSO (used for In-System Programming)P1.7 SCK(used for In-System Programming)Port 2 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 2 output buffers can sink/source four TTL

10、inputs. When 1s are written to Port 2 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups.Port 2 emits the high-order address byte during fetches from ext

11、ernal program memory and during accesses to external data memory that use 16-bit addresses (MOVX DPTR). In this application, Port 2 uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX RI), Port 2 emits the contents of the P2 Special

12、Function Register. Port 2 also receives the high-order address bits and some control signals during Flash programming and verification.Port 3 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins, the

13、y are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pull-ups. Port 3 receives some control signals for Flash programming and verification. Port 3 also serves the functions of variou

14、s special features of the AT89S51, as shown in the following table.Port PinAlternate FunctionsP3.0RXD(serial input port)P3.1TXD(serial output port)P3.2INT0(external interrupt 0)P3.3INT1(external interrupt 1)P3.4T0(timer 0 external input)P3.5T1(timer 1 external input)P3.6WR(external data memory write

15、 strobe)P3.7RD(external data memory read strobe)3 Special Function RegistersA map of the on-chip memory area called the Special Function Register (SFR) space is shown in Table 3-1. Table 3-1. AT89S51 SFR Map and Reset Values0F8H 0FFH 0F0H B 0F7H 0E8H 0EFH 0E0H ACC 0E7H 0D8H 0DFH 0D0H PSW 0D7H 0C8H 0

16、CFH 0C0H 0C7H 0B8H IP XX 0BFH 0B0H P3 0B7H 0A8H IE 0X 0AFH 0A0H P2 AUXR1 XXXXXXX0 WDTRST XXXXXXXX 0A7H 98H SCON SBUF XXXXXXXX 9FH 90H P1 97H 88H TCON TMOD TL0 TL1 TH0 TH1 AUXR XXX00XX 8FH 80H P0 SP DP0L DP0H DP1L DP1H PCON 0XXX0000 87H Note that not all of the addresses are occupied, and unoccupied

17、addresses may not be implemented on the chip. Read accesses to these addresses will in general return random data, and write accesses will have an indeterminate effect. User software should not write 1s to these unlisted locations, since they may be used in future products to invoke new features. In

18、 that case, the reset or inactive values of the new bits will always be 0. Interrupt Registers: The individual interrupt enable bits are in the IE register. Two priorities can be set for each of the five interrupt sources in the IP register.Table 3-2. AUXR:Auxiliary RegisterAUXR Address=8EH Reset Va

19、lue=XXX00XX0b Not Bit Addressable WDIDLE DISRTO DISALEBit 7 6 5 4 3 2 1 0 Reserved for future expansionDISALE Disable/Enable ALE DISALE Operating Mode 0 ALE is emitted at a constant rate of 1/6 the oscillator frequency 1 ALE is active only during a MOVX or MOVC instruction DISRTO Disable/Enable Rese

20、t-out DISRTO 0 Reset pin is driven High after WDT times out 1 Reset pin is input only WDIDLE Disable/Enable WDT in IDLE modeWDIDLE0 WDT continues to count in IDLE mode 1 WDT halts counting in IDLE mode Dual Data Pointer Registers: To facilitate accessing both internal and external data memory, two b

21、anks of 16-bit Data Pointer Registers are provided: DP0 at SFR address locations 82H-83H and DP1 at 84H-85H. Bit DPS = 0 in SFR AUXR1 selects DP0 and DPS = 1 selects DP1. The user should always initialize the DPS bit to the appropriate value before accessing the respective Data Pointer Register.Powe

22、r Off Flag: The Power Off Flag (POF) is located at bit 4 (PCON.4) in the PCON SFR. POF is set to “1” during power up. It can be set and rest under software control and is not affected by reset.4 Memory OrganizationMCS-51 devices have a separate address space for Program and Data Memory. Up to 64K by

23、tes each of external Program and Data Memory can be addressed.4.1 Program MemoryIf the EA pin is connected to GND, all program fetches are directed to external memory. On the AT89S51, if EA is connected to VCC, program fetches to addresses 0000H through FFFH are directed to internal memory and fetch

24、es to addresses 1000H through FFFFH are directed to external memory.4.2 Data MemoryThe AT89S51 implements 128 bytes of on-chip RAM. The 128 bytes are accessible via direct and indirect addressing modes. Stack operations are examples of indirect addressing, so the 128 bytes of data RAM are available

25、as stack space.5 Watchdog Timer (One-time Enabled with Reset-out) The WDT is intended as a recovery method in situations where the CPU may be subjected to software upsets. The WDT consists of a 14-bit counter and the Watchdog Timer Reset (WDTRST) SFR. The WDT is defaulted to disable from exiting res

26、et. To enable the WDT, a user must write 01EH and 0E1H in sequence to the WDTRST register (SFR location 0A6H). When the WDT is enabled, it will increment every machine cycle while the oscillator is running. The WDT timeout period is dependent on the external clock frequency. There is no way to disab

27、le the WDT except through reset (either hardware reset or WDT overflow reset). When WDT overflows, it will drive an output RESET HIGH pulse at the RST pin.5.1 Using the WDTTo enable the WDT, a user must write 01EH and 0E1H in sequence to the WDTRST register (SFR location 0A6H). When the WDT is enabl

28、ed, the user needs to service it by writing 01EH and 0E1H to WDTRST to avoid a WDT overflow. The 14-bit counter overflows when it reaches 16383 (3FFFH), and this will reset the device. When the WDT is enabled, it will increment every machine cycle while the oscillator is running. This means the user

29、 must reset the WDT at least every 16383 machine cycles. To reset the WDT the user must write 01EH and 0E1H to WDTRST. WDTRST is a write-only register. The WDT counter cannot be read or written. When WDT overflows, it will generate an output RESET pulse at the RST pin. The RESET pulse duration is 98

30、xTOSC, where TOSC = 1/FOSC. To make the best use of the WDT, it should be serviced in those sections of code that will periodically be executed within the time required to prevent a WDT reset.5.2 WDT DURING Power-down and IdleIn Power-down mode the oscillator stops, which means the WDT also stops. W

31、hile in Power-down mode, the user does not need to service the WDT. There are two methods of exiting Power-down mode: by a hardware reset or via a level-activated external interrupt, which is enabled prior to entering Power-down mode. When Power-down is exited with hardware reset, servicing the WDT

32、should occur as it normally does whenever the AT89S51 is reset. Exiting Power-down with an interrupt is significantly different. The interrupt is held low long enough for the oscillator to stabilize. When the interrupt is brought high, the interrupt is serviced. To prevent the WDT from resetting the

33、 device while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high. It is suggested that the WDT be reset during the interrupt service for the interrupt used to exit Power-down mode. To ensure that the WDT does not overflow within a few states of exiting Power-dow

34、n, it is best to reset the WDT just before entering Power-down mode. Before going into the IDLE mode, the WDIDLE bit in SFR AUXR is used to determine whether the WDT continues to count if enabled. The WDT keeps counting during IDLE (WDIDLE bit = 0) as the default state. To prevent the WDT from reset

35、ting the AT89S51 while in IDLE mode, the user should always set up a timer that will periodically exit IDLE, service the WDT, and reenter IDLE mode.With WDIDLE bit enabled, the WDT will stop to count in IDLE mode and resumes the count upon exit from IDLE.6.InterruptsThe AT89S51 has a total of five i

36、nterrupt vectors: two external interrupts (INT0 and INT1), two timer interrupts (Timers 0 and 1), and the serial port interrupt. These interrupts are all shown in Figure 6-1. Each of these interrupt sources can be individually enabled or disabled by setting or clearing a bit in Special Function Regi

37、ster IE. IE also contains a global disable bit, EA, which disables all interrupts at once.Note that Table 6-1 shows that bit positions IE.6 and IE.5 are unimplemented. User software should not write 1s to these bit positions, since they may be used in future AT89 products. The Timer 0 and Timer 1 fl

38、ags, TF0 and TF1, are set at S5P2 of the cycle in which the timers overflow. The values are then polled by the circuitry in the next cycle. Figure 6-1 Interrupt Sources7 Oscillator Characteristics XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier that can be configure

39、d for use as an on-chip oscillator, as shown in Figure 7-1. Either a quartz crystal or ceramic resonator may be used. To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven, as shown in Figure 7-2. There are no requirements on the duty cycle of the

40、external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum voltage high and low time specifications must be observed.Figure 7-1 Oscillator ConnectionsNote: for Crystals for Ceramic ResonatorsFigure 7-2 External Clock Drive

41、Configuration8 Idle Mode In idle mode, the CPU puts itself to sleep while all the on-chip peripherals remain active. The mode is invoked by software. The content of the on-chip RAM and all the special function registers remain unchanged during this mode. The idle mode can be terminated by any enable

42、d interrupt or by a hardware reset. Note that when idle mode is terminated by a hardware reset, the device normally resumes pro-gram execution from where it left off, up to two machine cycles before the internal reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this

43、event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write to a port pin when idle mode is terminated by a reset, the instruction following the one that invokes idle mode should not write to a port pin or to external memory.9 Power-down Mode In the Power

44、-down mode, the oscillator is stopped, and the instruction that invokes Power-down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values until the Power-down mode is terminated. Exit from Power-down mode can be initiated either by a hardware reset or by

45、 activation of an enabled external interrupt (INT0 or INT1). Reset redefines the SFRs but does not change the on-chip RAM. The reset should not be activated before VCC is restored to its normal operating level and must be held active long enough to allow the oscillator to restart and stabilize.Table

46、 9-1 Status of External Pins During Idle and Power-down ModesModeProgram MemoryALEPSENPORT0PORT1PORT2PORT3IdleInternal 1 1DataDataDataDataIdleExternal 1 1FloatDataAddressDataPower-downInternal 0 0DataDataDataDataPower-downExternal 0 0FloatDataDataData 专心-专注-专业译文AT89S51概述1 一般概述 该AT89S51是一个低功耗，高性能CMOS 8位微控制器,可在4K字节的系统内编程的闪存存储器。该设备是采用Atmel的高密度、非易失性存储器技术和符合工业标准的80C51指令集和引脚。芯片上的Flash程序存储器在系统中可重新编程或常规非易失性内存编程 。通过结合通用8位中央处理器的系统内可编程闪存的单芯片， AT89S51是一个功能强大的微控制器提供了高度灵