Roads in Hertfordshire 3rd edition Volume 3 Pre Consultation 在哈福德郡第三版3卷前咨询的道路.doc

《Roads in Hertfordshire 3rd edition Volume 3 Pre Consultation 在哈福德郡第三版3卷前咨询的道路.doc》由会员分享，可在线阅读，更多相关《Roads in Hertfordshire 3rd edition Volume 3 Pre Consultation 在哈福德郡第三版3卷前咨询的道路.doc（5页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、 Roads in Hertfordshire: Highway Design Guide3rd EditionVolume 4 - Design Standards and AdviceChapter 7 Road Restraint Systems7. Road Restraint Systems (Vehicle and Pedestrian)1.1.Vehicle Restraint Systems (VRS)21.2.Pedestrian Restraint Systems31.2.1.Pedestrian Crossings31.2.2.Pedestrian Parapets31.

2、2.3.Pedestrian Restraint and Protection at Head Walls, Wing Walls and Retaining Walls.47.1. Vehicle Restraint Systems (VRS)Refer to Section5, Chapter 5 Road Restraint Systems (Vehicle and Pedestrian) (Series 400).Vehicle Restraint Systems (VRS) are systems installed on a road to provide a level of c

3、ontainment for errant vehicles. They will not normally be required on single carriageway roads with speed limits less than 50mph.There may, however, be circumstances where protection is required to prevent large vehicles from colliding with structures. There may also be a specific need to provide pr

4、otection where a hazard such as a river, road, railway or pedestrian subway passes underneath the road. See also TD19 chapter 3 for the General Requirements, including visibility, set-back, working width class and lists of hazards for consideration of protection. For these circumstances, a risk asse

5、ssment should be carried out using the guidance given in TD19 para.1.2.3 for roads with speed limits of less than 50mph.Where VRS are to be provided on roads where the speed limit is 50mph or higher, then they shall conform to the requirements in TD19 DMRB 2.2.8.TD19 is now a risk based Standard and

6、 does not follow the conventional Standard format. The Standard has two parts that must be used together, namely: the written Standard TD19 Requirement for RRS DMRB 2.2.8 and the Road Restraint Risk Assessment Process (RRRAP), which is software driven. This software is available from; and is located

7、 in “Doing Business With Us/Technical Information.Road furniture must not be positioned in front of a new or existing VRS and, in general, it should not be placed immediately in advance of nor within the available working width of a new or existing VRS unless the road furniture has been designed to

8、be passively safe, and if hit, will not be displaced into the adjacent carriageway or give rise to a secondary event. Refer to TD19 paras.3.123 to 3.128 for use of passively safe lighting columns and signs.There may be circumstances where due to physical geometric restraints, a VRS cannot be accommo

9、dated within the TD19 standard for roads with speeds of greater than 50mph.Relaxations may be introduced at the discretion of HCC, having regard to advice and guidance given in TD19 and all relevant local factors.Careful consideration must be given to layout options and the effects of incorporating

10、relaxations, having weighed the benefits and potential disadvantages. The preferred option must be compared against options that would meet full standards. It is recommended that the details of the relaxation and justification are copied to HCC before incorporation into the works, (See TD19 paragrap

11、hs 1.37 and 1.38).Where special circumstances arise and the technical requirements for provision of a VRS cannot be achieved for some reason, users are encouraged to come forward with departures which go beyond relaxations from criteria, or to propose additional criteria based on a reasoned assessme

12、nt. Details of the departure and justification should be copied to HCC in order for the proposals tobe assessed, (See TD19 paragraphs 1.39 and 1.40).Where a Contractor needs to use a VRS as part of Temporary Traffic Management, then it shall conform to the requirements given in TD19 Chapter 8.Road S

13、afety Audits must be undertaken on all highway schemes involving removal, provision or improvement of VRS in accordance with HD19 DMRB 5.2.2.7.2. Pedestrian Restraint SystemsReference should be made to Chapter 9 of TD19 for further guidance on Pedestrian Restraint Systems.7.2.1. Pedestrian Crossings

14、The minimum height of pedestrian guardrail or pedestrian parapet must be:UsersGuardrailParapets(drops over 1.2m)Not over railwayOver railwayPedestrian1.0m1.15m1.5mCyclist1.0m1.4m1.5mEquestrian1.8m1.8m1.8mTable 4.7.2.1:Minimum Guardrail or Parapet HeightsReference should be made to Chapter 4 of TD19

15、for accepted heights of parapets and Chapter 9 of TD19 for information on Pedestrian Restraint Systems.Many accidents at pedestrian crossings occur on the approach to the crossing. The provision of pedestrian guard railing at such positions should be considered. However, there is a growing realisati

16、on that the excessive use of such features has caused substantial aesthetic damage to our towns and cities as well as being a deterrent to walking and a potential hazard to cyclists. High Inter Visibility pedestrian guard railing may be required to give motorists a clear view of waiting pedestrians.

17、 The appropriate type guard railing will depend on the geometric layout of the crossing facility, (See manufacturers details for the various types of guard railing to be used in different scenarios, be it on a straight road or on a bend).The effectiveness of guard railing is lessened if gaps have to

18、 be left for access for vehicles and the loading and unloading of goods. Where possible, crossings should be sited to avoid the necessity for such gaps.Pedestrian guard railing at traffic signal controlled crossings should start at the signal post but not encroach beyond the push button position.It

19、is desirable in some cases to restrict the crossing of pedestrians to certain approaches. This may be the case at a traffic signal controlled junction or where a change in direction is required across an island such as a roundabout. Pedestrian guard rails can be used to prevent pedestrians crossing

20、at dangerous places (for example where filtering traffic may be moving at times unexpected by pedestrians).Pedestrian guard rails should not be provided as a deterrent to kerbside vehicle parking.7.2.2. Pedestrian ParapetsAll footbridges and bridleway bridges must be provided with pedestrian parapet

21、s conforming to the requirements of BS7818.Pedestrian parapets on bridges over railways are subject to special design requirements with respect to infill panels, as detailed in BS7818 and the design and material must be approved by the Railway Authority.On cycleway bridges or accommodation bridges f

22、requently used by equestrians, the height of the parapet above the adjoining paved surface must be increased to 1.8m, and a 600mm high solid infill panel must be provided at the bottom of the parapet in order to obstruct the animals view of the road below.7.2.3. Pedestrian Restraint and Protection a

23、t Head Walls, Wing Walls and Retaining Walls.Where any pedestrian movement may occur within the highway from use or maintenance of the highway and there is a risk to health and safety from a fall from a height, suitable protective measures must be provided in accordance with the requirements detaile

24、d below.Where a structure, such as a retaining wall, head wall or wing wall, presents a vertical or near vertical face 1.5m or more in height and it would be possible for a person to gain access to the upper edge of the structure, a pedestrian restraint system such as a protective barrier or guard r

25、ail must be installed close to, or on top of the structure. A pedestrian protective barrier or guard rail must also be installed at walls less than 1.5m in height if a particular hazard, such as a watercourse, or road, is near the wall.The type of pedestrian protective measure to be used will need to be determined locally and be in keeping with any structural, drainage, environmental and aesthetic considerations. The protective measures could include pedestrian guard railing, pedestrian parapet or appropriate types of boundary fencing.