外文翻译文献(共14页).doc

《外文翻译文献(共14页).doc》由会员分享，可在线阅读，更多相关《外文翻译文献(共14页).doc（14页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上毕 业 设 计（论文）外 文 文 献 翻 译题 目：基于DSP的单相恒压逆 变器设计 教 学 院： 电气与电子信息工程学院专业名称： 电气工程及其自动化 学 号： 1 学生姓名： 明寿 指导教师： 马学军 2014 年 5月10日专心-专注-专业逆变器 SHITingNa,WANGJian1引言逆变器是一种电动装置，转换成直流电（DC），交流电流转换的AC（交流）可以在任何所需的电压和频率使用适当的变压器，开关，控制circuits.Solid状态逆变器有没有移动部件，用于广泛的应用范围从小型计算机开关电源，高压大型电力公司电力，运输散装直接电流应用。逆变器通常用于提

2、供交流电源，直流电源，如太阳能电池板或电池。逆变器的主要有两种类型。修改后的正弦波逆变器的输出是类似方波输出，输出变为零伏前一段时间切换积极或消极的除外。它是简单，成本低，是大多数电子设备兼容，除敏感或专用设备，例如某些激光打印机。一个纯正弦波逆变器产生一个近乎完美的正弦波输出（3的总谐波失真），本质上是相同的公用事业提供电网。因此，它是与所有的交流电的电子设备兼容。这是在电网领带逆变器使用的类型。它的设计更复杂，成本5或10倍以上每单位功率电逆变器是一个高功率的电子振荡器。它这样命名，因为早期的机械AC到DC转换器工作在反向，因而被“倒”，将直流电转换AC.The变频器执行的整流器对面功能。

3、2应用2.1直流电源利用率 逆变器从交流电力来源，如电池，太阳能电池板，燃料电池的直流电转换成。电力，可以在任何所需的电压，特别是它可以操作交流电源操作而设计的设备，或纠正，以产生任何所需的voltage Grid领带逆变器的直流送入分销网络的能量，因为它们产生电流交替使用相同的波形和频率分配制度提供。他们还可以关掉一个blackout.Micro逆变器的情况下自动转换成交流电电网的电流直接从当前个别太阳能电池板。默认情况下，他们是格领带设计。2.2不间断电源不间断电源（UPS），电池和逆变器，交流电源，主电源不可用时使用。当主电源恢复正常时，整流提供直流电源给电池充电。2.3感应加热逆变器的

4、低频交流主电源转换到更高频率的感应加热使用。要做到这一点，首先纠正交流电源提供直流电源。逆变器，然后改变高频率的交流电源，直流电源。2.4高压直流输电随着高压直流输电，交流电源经过整流和高压直流电源传输到另一个位置。在接收的位置，在静态逆变器厂逆变器转换回交流电源。2.5变频驱动器一个变频驱动控制向电动机提供电源的频率和电压控制交流电机的运行速度。逆变器提供控制电源。在大多数情况下，变频驱动，包括整流器，使逆变器的直流电源，可从交流主电源提供。由于逆变器是关键部件，变频驱动，有时被称为逆变器驱动器，或只是逆变器。2.6电动汽车驱动器目前使用的权力，在一些电动和柴油 - 电动轨道车辆以及一些电池

5、的电动汽车和混合动力电动公路车辆，如丰田Prius和菲斯克噶牵引电机调速电机控制逆变器。变频技术的各种改进正在开发专门用于电动汽车的应用。2在再生制动的车辆，逆变器也需要从电机（作为发电机）的权力，并储存在电池中。2.7一般情况下 一个变压器，使交流电源转换为任何所需的电压，但在相同的频率。直流逆变器，加上整流器，可以被用来转换从任何电压，交流或直流，任何其他的电压，也交流或直流，在任何所需的频率。输出功率不能超过输入功率，但效率高的余热消耗的功率小的比例。3电路描述3.1基本设计在一个简单的逆变电路，直流电源连接到变压器初级绕组中心抽头通过。一个正在迅速来回切换开关允许电?流流回直流电源后，

6、两个备用路径，然后通过初级绕组的一端其他。在变压器的初级绕组中的电流方向交替产生交流电（AC）在二次回路。机电开关设备的版本包括两个固定触点和支持动触头弹簧。春天拥有对固定触点之一的可移动的接触和电磁铁拉动产接触到相对固定的联系。在电磁铁的电流被中断的开关，使开关不断来回切换迅速的行动。这种机电逆变器开关的类型，称为一个振动器或蜂鸣器，曾一度被用于真空管汽车收音机。类似的机制已被用于门铃，蜂鸣器和纹身枪。当他们成为具有足够的额定功率，晶体管和其他各种类型的半导体开关逆变电路设计已纳入。3.2输出波形 如上所述，在简单的逆变器开关时不耦合到输出变压器，产生一个方形的电压波形作为反对的是平常的交流

7、电源波形的正弦的波形，由于其简单的关闭和对自然的。使用傅立叶分析，周期性波形表示作为正弦波无穷级数的总和。原始波形正弦波具有相同的频率被称为基本组成部分。其他正弦波，称为谐波，该系列包括有频率是基本频率的整数倍。需要从变频器的输出波形的质量取决于所连接的负载的特点。一些负载需要一个近乎完美的正弦波电源电压才能正常工作。方波电压与其他负载可能工作得非常好。3.3三阶段逆变器用于三相逆变器变频驱动应用和高功率应用，如高压直流输电。一个基本的三个单相逆变器的三相逆变器组成，每个交换机连接到三个负载端子。三层交换机的运作最基本的控制计划，协调，使一台交换机工作在60度的基本输出波形的每个点。这将创建一

8、个线到线输出波形有六个步骤。六步波形方波是3的倍数的谐波消除如上所述的正面和负面的部分之间的零电压的一步。当舰载PWM技术应用于六步波形，基本整体造型，或信封的波形，保留3次谐波及其倍数，使被消除。4历史4.1早期的逆变器从十九世纪末到二十世纪中叶，直流 - 交流功率转换完成使用旋转器或马达发电机组（爵套）。在二十世纪初，真空管和充满气体管开始被用于逆变器电路中的开关。最广泛使用的管型晶闸管。机电逆变器的起源解释源长期变频器。早期的AC至DC转换器采用感应或同步交流电机直接连接到一台发电机（发电机），使发电机的整流子扭转在正确的时刻其连接生产直流。后来的发展是同步的转换器，电机和发电机绕组结合

9、成一个电枢，一端与滑环和整流子在其他只有一个领域的框架。结果要么是交流，直流。与MG组，直流，可考虑将分别从AC生成，同步器，它在一定意义上可以认为是“机械纠正交流”。由于正确的辅助设备和控制设备，MG集或旋转转换，可以“倒着跑”，将直流转换为交流电。因此，逆变器是一个倒置的转换。 4.2可控整流逆变器自从1957年初年初以来，晶体管不能提供足够的电压和额定电流最逆变器应用，它是1957年的晶闸管或可控硅（SCR）的介绍，开始过渡到固态逆变电路。可控硅的换相的条件是在可控硅电路设计的关键考虑因素。不要关闭可控硅整流自动门控制信号被切断时。他们只关闭当正向电流降至低于最低维持电流，每一种可控硅变

10、化，通过一些外部进程。对于连接到交流电源的可控硅，整流发生自然每次源?电压极性反转。可控硅直流电源连接到通常需要强迫换，强制要求减刑时电流为零的一种手段。最复杂的可控硅电路采用自然，而不是被迫换减刑。此外被迫换电路，可控硅已被用于在以上所述的逆变器电路的类型。在逆变器传输到AC电源由直流电源供电的应用程序，它可以使用交流 - 直流可控整流电路的反演模式经营。在反演模式，可控整流电路整流逆变器行。这种类型的操作，可用于高压直流输电系统和再生制动电机控制系统的操作。另一种类型的可控硅逆变电路是电流源输入（CSI）逆变器。一个CSI逆变器是一个六步的电压源逆变器的双。用一个电流源逆变器，直流电源作为

11、电流源而非电压源配置。变频器可控硅开关在六步序列直接阶梯电流波形作为一个三相交流负载的电流。沪深逆变器换方法包括整流负载和并联电容器减刑。这两种方法，输入电流调节协助减刑。带整流负载，负载是在领先的功率因数运行的同步电机。因为他们已经成为在更高的额定电压和电流，如可以通过控制信号的晶体管或IGBT的半导体已成为首选开关元件逆变电路使用。4.3整流器和逆变器的脉冲数整流电路往往流的每个周期的AC输入电压整流的直流侧电流脉冲的数量分类。单相半波整流是一个脉冲电路和单相全波整流是两个脉冲的电路。一个三相半波整流是一个三脉冲电路和三相全波整流是一个六脉冲电路。两个或两个以上的整流器三相整流器，有时串联

12、或并联连接以获得更高的电压或额定电流。提供特种变压器提供相移输出整流器的输入。这有相乘法效应。六个阶段是从两个变压器，12个阶段从三变等。 12脉冲整流器，18脉冲整流器等相关的整流电路。当可控整流电路的反演模式在运作，他们将分为脉冲数也。整流电路具有较高的脉冲数减少交流输入电流和减少直流输出电压纹波的谐波含量。在反演模式，有较高的脉冲个数的电路，在AC输出电压波形的谐波含量较低。5 参考文献 1 R. Organti, K. Nagaswamy, L. Sang, Predicted equal charge creterion scheme for constant frequency c

13、ontrol of single phase boost-type AC-DC converter, IEEE Trans. Power Electron 13 (1) (1998) 47-57.2 M. Ohshima, E. Masada, A single-phase PCS with a novel constantly sampled current-regulated PWM scheme, IEEE Trans. Power Electron 14 (5) (1999) 823-830.3 T. Toshida, O. Shiizuka, O. Miyashita, K. Ohn

14、iwa, An improvement technique for the efficiency of high-frequency switch-mode rectifiers, IEEE Trans. Power Electron 15 (6) (2000) 1118-1123.4 R. Sriniuasan,R. Oruganti,A unity power factor converter using half-bridge boost topology, IEEE Trans.Power Electron 13(3)(1998) 487-500.5 K. Itako, T. Mori

15、, A high performance rectifier control system with feedforward control and DC resonance filter, in: International Conference on Electrical Engineering 2005, Kunming, China, July 10-14, 2005.6 K. Itako, T. Mori. Full bridge PWM rectifier with load current feedforward, in: International Conference on

16、Electrical Engineering, Hong Kong, 2009.7 W. Leonhard, Control of Electrical Drives, 3rd ed.,Springer, 2001, pp. 160-162.Inverter SHITingNa,WANGJian1 IntroductionAn inverter is an electrical device that converts (DC) to (AC); the converted AC can be at any required voltage and frequency with the use

17、 of appropriate , switching, and control circuits.Solid-state inverters have no moving parts and are used in a wide range of applications, from small in computers, to large applications that transport bulk power. Inverters are commonly used to supply AC power from DC sources such as or .There are tw

18、o main types of inverter. The output of a modified sine wave inverter is similar to a output except that the output goes to zero volts for a time before switching positive or negative. It is simple and low cost and is compatible with most electronic devices, except for sensitive or specialized equip

19、ment, for example certain . A pure sine wave inverter produces a nearly perfect sine wave output (3% ) that is essentially the same as utility-supplied grid power. Thus it is compatible with all AC electronic devices. This is the type used in grid-tie inverters. Its design is more complex, and costs

20、 5 or 10 times more per unit power The electrical inverter is a high-power . It is so named because early were made to work in reverse, and thus were inverted, to convert DC to AC.The inverter performs the opposite function of a .2 Applications2.1 DC power source utilizationAn inverter converts the

21、DC electricity from sources such as , , or to AC electricity. The electricity can be at any required voltage; in particular it can operate AC equipment designed for mains operation, or rectified to produce DC at any desired voltage can feed energy back into the distribution network because they prod

22、uce alternating current with the same wave shape and frequency as supplied by the distribution system. They can also switch off automatically in the event of a . convert direct current from individual solar panels into alternating current for the electric grid. They are grid tie designs by default.

23、2.2 Uninterruptible power suppliesAn (UPS) uses batteries and an inverter to supply AC power when main power is not available. When main power is restored, a supplies DC power to recharge the batteries.2.3 Induction heatingInverters convert low frequency main AC power to a higher frequency for use i

24、n . To do this, AC power is first to provide DC power. The inverter then changes the DC power to high frequency AC power. 2.4 HVDC power transmissionWith power transmission, AC power is rectified and high voltage DC power is transmitted to another location. At the receiving location, an inverter in

25、a converts the power back to AC.2.5 Variable-frequency drivesA controls the operating speed of an AC motor by controlling the frequency and voltage of the power supplied to the motor. An inverter provides the controlled power. In most cases, the variable-frequency drive includes a so that DC power f

26、or the inverter can be provided from main AC power. Since an inverter is the key component, variable-frequency drives are sometimes called inverter drives or just inverters.2.6 Electric vehicle drivesAdjustable speed motor control inverters are currently used to power the in some and rail vehicles a

27、s well as some and highway vehicles such as the and . Various improvements in inverter technology are being developed specifically for electric vehicle applications. In vehicles with , the inverter also takes power from the motor (now acting as a generator) and stores it in the batteries. 2.7 The ge

28、neral caseA allows AC power to be converted to any desired voltage, but at the same frequency. Inverters, plus rectifiers for DC, can be designed to convert from any voltage, AC or DC, to any other voltage, also AC or DC, at any desired frequency. The output power can never exceed the input power, b

29、ut efficiencies can be high, with a small proportion of the power dissipated as waste heat. 3 Circuit description 3.1 Basic designs In one simple inverter circuit, DC power is connected to a through the centre tap of the primary winding. A switch is rapidly switched back and forth to allow current t

30、o flow back to the DC source following two alternate paths through one end of the primary winding and then the other. The alternation of the direction of current in the primary winding of the transformer produces (AC) in the secondary circuit. The electromechanical version of the switching device in

31、cludes two stationary contacts and a spring supported moving contact. The spring holds the movable contact against one of the stationary contacts and an electromagnet pulls the movable contact to the opposite stationary contact. The current in the electromagnet is interrupted by the action of the sw

32、itch so that the switch continually switches rapidly back and forth. This type of electromechanical inverter switch, called a or buzzer, was once used in automobile radios. A similar mechanism has been used in door bells, buzzers and .As they became available with adequate power ratings, and various

33、 other types of switches have been incorporated into inverter circuit designs3.2 Output waveformsThe switch in the simple inverter described above, when not coupled to an output transformer, produces a square voltage due to its simple off and on nature as opposed to the waveform that is the usual wa

34、veform of an AC power supply. Using , waveforms are represented as the sum of an infinite series of sine waves. The sine wave that has the same as the original waveform is called the fundamental component. The other sine waves, called harmonics, that are included in the series have frequencies that

35、are integral multiples of the fundamental frequency.The quality of output waveform that is needed from an inverter depends on the characteristics of the connected load. Some loads need a nearly perfect sine wave voltage supply in order to work properly. Other loads may work quite well with a square

36、wave voltage. 3.3 Three phase inverters inverters are used for applications and for high power applications such as power transmission. A basic three-phase inverter consists of three single-phase inverter switches each connected to one of the three load terminals. For the most basic control scheme,

37、the operation of the three switches is coordinated so that one switch operates at each 60 degree point of the fundamental output waveform. This creates a line-to-line output waveform that has six steps. The six-step waveform has a zero-voltage step between the positive and negative sections of the s

38、quare-wave such that the harmonics that are multiples of three are eliminated as described above. When carrier-based PWM techniques are applied to six-step waveforms, the basic overall shape, or envelope, of the waveform is retained so that the 3rd harmonic and its multiples are cancelled.4 History4

39、.1 Early invertersFrom the late nineteenth century through the middle of the twentieth century, DC-to-AC was accomplished using or sets (M-G sets). In the early twentieth century, and began to be used as switches in inverter circuits. The most widely used type of tube was the .The origins of electro

40、mechanical inverters explain the source of the term inverter. Early AC-to-DC converters used an induction or synchronous AC motor direct-connected to a generator (dynamo) so that the generators commutator reversed its connections at exactly the right moments to produce DC. A later development is the

41、 synchronous converter, in which the motor and generator windings are combined into one armature, with slip rings at one end and a commutator at the other and only one field frame. The result with either is AC-in, DC-out. With an M-G set, the DC can be considered to be separately generated from the

42、AC; with a synchronous converter, in a certain sense it can be considered to be mechanically rectified AC. Given the right auxiliary and control equipment, an M-G set or rotary converter can be run backwards, converting DC to AC. Hence an inverter is an inverted converter. 4.2 Controlled rectifier i

43、nvertersSince early transistors were not available with sufficient voltage and current ratings for most inverter applications, it was the 1957 introduction of the or (SCR) that initiated the transition to inverter circuits.The commutation requirements of SCRs are a key consideration in SCR circuit d

44、esigns. SCRs do not turn off or commutate automatically when the gate control signal is shut off. They only turn off when the forward current is reduced to below the minimum holding current, which varies with each kind of SCR, through some external process. For SCRs connected to an AC power source,

45、commutation occurs naturally every time the polarity of the source voltage reverses. SCRs connected to a DC power source usually require a means of forced commutation that forces the current to zero when commutation is required. The least complicated SCR circuits employ natural commutation rather th

46、an forced commutation. With the addition of forced commutation circuits, SCRs have been used in the types of inverter circuits described above.In applications where inverters transfer power from a DC power source to an AC power source, it is possible to use AC-to-DC controlled rectifier circuits ope

47、rating in the inversion mode. In the inversion mode, a controlled rectifier circuit operates as a line commutated inverter. This type of operation can be used in HVDC power transmission systems and in operation of motor control systems.Another type of SCR inverter circuit is the current source input

48、 (CSI) inverter. A CSI inverter is the of a six-step voltage source inverter. With a current source inverter, the DC power supply is configured as a rather than a . The inverter SCRs are switched in a six-step sequence to direct the current to a three-phase AC load as a stepped current waveform. CSI inverter commutation methods include load commutation and parallel capacitor commutation. With both methods, the input curr