HAT833-HAT833S英文说明书.pdf

《HAT833-HAT833S英文说明书.pdf》由会员分享，可在线阅读，更多相关《HAT833-HAT833S英文说明书.pdf（57页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、 HAT833(HAT833/HAT833S)THREE POWER ATS CONTROLLER USER MANUAL All rights reserved.No part of this publication may be reproduced in any material form(including photocopying or storing in any medium by electronic means or other)without the written permission of the copyright holder.Applications for th

2、e copyright holders written permission to reproduce any part of this publication should be addressed to SmartGen Technology at the address above.Any reference to trademarked product names used within this publication is owned by their respective companies.SmartGen Technology reserves the right to ch

3、ange the contents of this document without prior notice.Table 1-Software Version Date Version Note 2018-10-16 1.0 Original release.2018-12-13 1.1 Modified controller front panel picture.2020-02-13 1.2 Modified typical application diagram,added mutual lock for each power close.2020-10-10 1.3 Modified

4、 the Chinese interface display of the controller.2021-04-20 1.4 1.Add the HAT833S function descriptions;2.Changed“Mains-Gen-Mains”to“Mains-Gen-Gen”in“Performance and characteristics”;3.Modified the manual font and the format of header and footer.CONTENT 1 OVERVIEW.5 2 NAMING CONVENTION AND MODEL COM

5、PARISON.6 2.1 NAMING CONVENTION.6 2.2 MODEL COMPARISON.6 3 PERFORMANCE AND CHARACTERISTICS.7 4 SPECIFICATION.8 5 MEASURE AND DISPLAY DATA.9 6 OPERATION.10 6.1 INDICATORS.10 6.2 KEY FUNCTION DESCRIPTION.11 7 LCD DISPLAY.12 7.1 MAIN SCREEN.12 7.2 STATUS DESCRIPTION.13 7.3 MAIN MENU.18 8 START/STOP OPE

6、RATION.19 8.1 MANUAL START/STOP.19 8.1.1 PANEL START/STOP.19 8.1.2 REMOTE START/STOP.20 8.2 AUTO START/STOP.20 8.2.1 START CONDITIONS.20 8.2.1.1 INPUT START.20 8.2.1.2 GEN START MAINS NG.20 8.2.1.3 GEN START MASTER.20 8.2.2 GEN-GEN START/STOP.20 8.2.3 SCHEDULED RUN.22 8.2.4 SCHEDULED NOT RUN.23 9 PA

7、RAMETERS CONFIGURATION.24 9.1 ILLUSTRATION.24 9.2 PARAMETERS TABLE.24 9.3 DIGITAL INPUT/OUTPUT FUNCTION DESCRIPTION.35 9.3.1 INPUT PORTS FUNCTION.35 9.3.2 OUTPUT PORTS FUNCTION.37 9.3.3 CUSTOM COMBINED.40 9.4 DEFINITE TIME DELAY AND INVERSE DEFINITE MINIMUM TIME SETTING.41 10 HISTORICAL RECORDS.42 1

8、1 BLACK BOX RECORDS.43 12 SWITCH OPERATION.44 12.1 MANUAL OPERATION.44 12.2 AUTOMATIC OPERATION.46 13 ATS POWER SUPPLY.47 14 NEL CONTROL.48 14.1 ILLUSTRATION.48 14.2 AUTO OPERATION.48 14.3 MANUAL OPERATION.48 15 COMMUNICATION CONFIGURATION.49 16 TERMINALS.50 17 TYPICAL WIRING DIAGRAM.54 18 INSTALLAT

9、ION.56 19 TROUBLE SHOOTING.57 1 OVERVIEW HAT833 Series Three Power ATS Controller is intelligent tri-supply module with configurable function,automatic measurement,LCD display,and digital communication.It combines digitization,intelligence and networking.Automatic measurement and control can reduce

10、incorrect operation,which is an ideal option for ATS.The powerful Microprocessor contained within the unit allows for precision voltage(3-way 3-phase)measuring and make accurate judgment and the corresponding volt free digital output port will active when there is over/under voltage,over/under frequ

11、ency,loss of phase,phase sequence wrong and other abnormal condition occurs.It has compact structure,advanced circuits,simple wiring and high reliability,and can be widely used in electrical automatic control system of electric power,telecommunications,petroleum,coal,metallurgy,railways,municipal ad

12、ministration,intelligent building,etc.2 NAMING CONVENTION AND MODEL COMPARISON 2.1 NAMING CONVENTION Fig.1 Naming Convention 2.2 MODEL COMPARISON Table 2 Model Comparison Functions Model DC Supply AC Supply Sync.Closing Input Port No.Output Port No.RS485 HAT833 8 12 HAT833S 8 12 3 PERFORMANCE AND CH

13、ARACTERISTICS System type can set as:Mains-Mains-Gen,Mains-Mains-Mains,Mains-Gen-Gen,etc;4.3 inchs solid color 240 x128 LCD display with white backlight,multilingual interface(including English,Simplified Chinese or other languages),push-button operation;Collect and display 3-way 3-phase voltage,fre

14、quency and phase sequence;Collect and display load active power,reactive power,apparent power,power factor and current;S1/S2/S3 separated over current warning/trip alarm;NEL(Non-essential Load)trip function;Display S1/S2/S3 total kW energy,total kvar energy,total close times;Display continuous power

15、 supply time and S1/S2/S3 total power supply time;For Stored-Energy type ATS,its close relay will active after the PF Input is active;Over/under voltage,over/under frequency,over current,loss of phase,phase sequence wrong protection;Automatic/Manual mode.In manual mode,can force the switch to close

16、or open;All parameters can be set on site.Passwords authentication ensures authorized staff operation only;The genset can be manual test on site to achieve start/stop operation;Automatic re-closing;Closing output signal can be set as on intervals or as continuous output;Applicable for 3 isolated neu

17、tral line;Real-time clock(RTC);event log function(event log can record 200 items circularly);Scheduled routing run&scheduled not run(can be set as start genset once a day/week/month whether with load or not);Can control two generators to work as cycle run mode,master run mode and balance run mode;Wi

18、dely DC power supply range allows the controller can bear instantaneous 80V DC input;Large terminal space allows the controller can bear maximum 625V AC voltage input;With Dual-RS485 isolated communication interface.With remote controlling,remote measuring,remote communication,remote regulating func

19、tion by the ModBus-RTU communication protocol.Can remote start/stop the genset and remote control the breaker to close or open;Suitable for various AC systems(3-phase 4-wire,3-phase 3-wire,single-phase 2-wire,and 2-phase 3-wire);Modular design,self extinguishing ABS plastic shell,pluggable terminal,

20、built-in mounting，compact structure with easy installation.4 SPECIFICATION Table 3 Performance Parameters Items Contents Operating Voltage 1.DC8.0V35.0V,continuous power supply 2.AC(90305)V power supply A1N1/A2N2/A3N3 Power Consumption S2S3 8.2.3 SCHEDULED RUN Once“Scheduled Run”enables,users can se

21、t the scheduled start time.Controller will send start signal at preset start time.Start signal will deactivated after the start delay has expired.“Scheduled Run On Load”or“Scheduled Run Off Load”can be set.Scheduled Run On Load:When the input is active,genset close relay will active after genset is

22、normal.Scheduled Run Off Load:When the input is active,mains close relay will active after mains is normal.Cycle time of Scheduled Run can be set as start monthly,weekly and daily.Run Monthly:Which month to start,start date and time can be set.Run Weekly:Can start the genset at the same time in coup

23、le days of a week.Eg.Start the genset at 8:00 a.m.from Monday to Friday and keep 10 hours.Run Daily:Can start the genset at same time everyday.8.2.4 SCHEDULED NOT RUN Once”Scheduled Not Run”enables,users can set the“Scheduled Not Start”time.Start signal will deactivated at preset time and it will be

24、 inhibited before the delay has expired.Cycle time of“Scheduled Not Run”can be set as monthly,weekly and daily.Not Run Monthly:Which month not start,not start date and time can be set.Not Run Weekly:Can not start the genset at the same time in couple days of a week.Eg.Not Start the genset at 19:00 p

25、.m.from Monday to Friday and keep 12 hours.Not Run Daily:Can not start the genset at same time everyday.Note 5:“Scheduled Not Run”operation is prior to“Scheduled Run”operation.9 PARAMETERS CONFIGURATION 9.1 ILLUSTRATION In the main interface,press key,choose Configuration and press again to enter in

26、to password confirmation interface.If password is correct,enter into parameter setting interface,otherwise,exit to main interface directly.Factory default password is 01234.In parameters configuration interface,pressing key to return the prior menu.9.2 PARAMETERS TABLE Table 18 Parameter Configurati

27、on Form No.Item Range Default Description AC Config 1 S1 Volt Normal(0-3600)s 10 The delay from S1 voltage abnormal to normal.2 S1 Volt Abnormal(0-3600)s 5 The delay from S1 voltage normal to abnormal.3 S2 Volt Normal(0-3600)s 10 The delay from S2 voltage abnormal to normal.4 S2 Volt Abnormal(0-3600

28、)s 5 The delay from S2 voltage normal to abnormal.5 S3 Volt Normal(0-3600)s 10 The delay from S3 voltage abnormal to normal.6 S3 Volt Abnormal(0-3600)s 5 The delay from S3 voltage normal to abnormal.7 Master Set(05)0 0:S1S2S3 1:S2S1S3 2:S3S1S2 3:S1S3S2 4:S2S3S1 5:S3S2S1 8 System Type (06)6 0:S1M S2G

29、 S3M 1:S1G S2M S3M 2:S1M S2M S3M 3:S1G S2G S3M 4:S1M S2G S3G 5:S1G S2M S3G 6:S1M S2M S3G 9 AC System(03)0 0:3 Phase,4 Wire(3P4W)1:3 Phase,3 Wire(3P3W)No.Item Range Default Description 2:2 Phase,3 Wire(2P3W)3:Single Phase,2 Wire(1P2W)10 PT Fitted(0-1)0 0:Disable;1:Enable 11 PT Primary(30-30000)V 100

30、Primary voltage of voltage transformer 12 PT Secondary(30-1000)V 100 Secondary voltage of voltage transformer 13 Rated Voltage(0-30000)V 220 Rated voltage of AC system 14 Over Volt Warn(0-1)1 0:Disable;1:Enable 15 Set Value(0-200)%120 Upper limit value of voltage;it is abnormal if the value has exce

31、eded the set value.16 Return(0-200)%115 Upper limit return value of voltage;it is normal only when the value has fallen below the set value.17 Under voltage Warn(0-1)1 0:Disable;1:Enable 18 Set Value(0-200)%80 Lower limit value of voltage;it is abnormal if the value has fallen below the set value.19

32、 Return Value(0-200)%85 Lower limit return value of voltage;it is normal only when the value has exceeded the set value.20 Rated Frequency(10.0-75.0)Hz 50.0 Rated frequency of AC system 21 Over Frequency Warn(0-1)1 0:Disable;1:Enable 22 Set Value(0-200)%110 Upper limit value of frequency;it is abnor

33、mal if the value has exceeded the set value.23 Return Value(0-200)%104 Upper limit return value of frequency;it is normal only when the value has fallen below the set value.24 Under Frequency Warn(0-1)1 0:Disable;1:Enable 25 Set Value(0-200)%90 Lower limit value of frequency;it is abnormal if the va

34、lue has fallen below the set value.26 Return Value(0-200)%96 Lower limit return value of frequency;it is normal only when the value has exceeded the set value.27 Phase Sequence Wrong(0-1)1 0:Disable;1:Enable Switch 1 Power Supply Type(01)1 0:DC Supply 1:AC Supply 2 AC Power Supply Voltage Lower Limi

35、t(0100)%70 The lowest AC power supply voltage,the switch will not transfer if it is lower than this value.3 AC Power Supply Voltage Upper Limit(0200)%200 The highest AC power supply voltage,the switch will not transfer if it is higher than this value.No.Item Range Default Description 4 Fixed Close/O

36、pen Time(0-1)0 0:Disable;1:Enable Disable:The output time was judged depends on the close relay;the longest output time up to the set delay.Enable:The output time last for the preset time.5 Close Delay(0.1-20.0)s 5.0 Pulse time of close relay.6 Open Delay(0.1-20.0)s 5.0 Pulse time of open relay.7 Tr

37、ansfer Interval(0-9999)s 1 Interval time from S1 switch open to S2 switch close;or from S2 switch open to S1 switch close.8 Auto Charge/Recover(0-1)1 0:Auto Charge Man Rec.1:Auto Charge/Rec.9 Again Close Delay(0-20.0)s 0.0 When the breaker fail to open for the first time,then the module will close f

38、or the second time and the Again Close Delay begins,after the delay has expired,if still failed to open for the second time,the module will send out fail to open alarm.10 Again Open Delay(0-20.0)s 0.0 When the breaker fail to close for the first time,then the module will open for the second time and

39、 the Again Open Delay begins,after the delay has expired,if still failed to close for the second time,the module will send out fail to close alarm.11 Forced Open Action(0-1)0 0:Warn Alarm 1:Fault Alarm 12 Continually Close(0-1)0 0:Disable;1:Enable If“Enable”is selected,“Close Time”and“Open Time”are

40、deactivated.13 Sync.Switching Enable(01)0 0:Disable 1:Enable 14 Sync.Voltage Difference Enable(01)0 0:Disable 1:Enable 15 Sync.Voltage Difference(050)V 5 The max.voltage difference when synchronization success.16 Sync.Frequency Difference(00.50)Hz 0.20 The max.frequence difference when synchronizati

41、on success.17 Sync.Phase Difference(020)5 The max.phase difference when synchronization success.18 Sync.Failure Alarm Action(01)0 0:Warning Alarm 1:Fault Alarm After sync.failure,it continues to wait for a synchronization until the switch is No.Item Range Default Description closed.Warning alarms,th

42、e alarm will be cleared when synchronization is finished or exited.Fault alarms,press alarm reset key to clear the alarm.19 Sync.Failure Forced Transfer(01)0 0:Disable 1:Enable After sync.failure,it will perform nonsynchronous closing and will not initiate a nonsynchronous.failure alarm.20 Sync.Fail

43、ure Delay(09999)s 120 Time to wait for sync.success,it fails to synchronize when the time exceeds the pre-set value.21 Dection Time for Sync.Closing/Opening(0.11.0)s 0.6 Sync.closing or opening output starts to delay when sync.switching,it will stop the closing/opening pulse output when it detects t

44、he correct closing status during the delay process.If it still can not detect the correct closing status when the delay ends,it will initiate a closing failure alarm or opening failure alarm.Generator 1 Start Delay(0-9999)s 1 When the genset is ready to start,start delay begins,after the start delay

45、 has expired,start signal will be initiated.2 Stop Delay(0-9999)s 5 When the genset is ready to stop,stop delay begins,after the stop delay has expired,stop signal will be initiated.3 Gen-Gen Start Mode(03)0 0:Cycs Run 1:Master Run 2:Balance Run 3:Not Used 4 S1 Cycle Running Time(0-9999)min 720 Gens

46、 cycle start S1 running time.5 S2 Cycle RunningTime(0-9999)min 720 Gens cycle start S2 running time.6 S3 Cycle RunningTime(0-9999)min 720 Gens cycle start S3 running time.7 Supply Delay(0-9999)s 120 When the start signal is active,the start delay will be initiated.If the gen voltage lasts abnormal a

47、fter the delay has expired,“Genset Fault”alarm will be initiated.No.Item Range Default Description 8 Battery Volt (0-1)0 0:Disable;1:Enable 9 Battery Under Volt Warn(0-1)0 0:Disable;1:Enable 10 Set Value(0-100.0)V 10.0“Battery Under Volts”alarm will be initiated if the battery voltage has fallen bel

48、ow the set value.11 Return Value(0-100.0)V 10.5“Battery Under Volts”alarm will be removed if the battery voltage has exceeded the set value.12 Battery Over Volt Warn(0-1)0 0:Disable;1:Enable 13 Set Value(0-100.0)V 30.0“Battery Over Volts”alarm will be initiated if the battery voltage has exceeded th

49、e set value.14 Return Value(0-100.0)V 29.5“Battery Over Volts”alarm will be removed if the battery voltage has fallen below the set value.Scheduler 1 Schedule Run(0-1)0 0:Disable;1:Enable 2 Run Mode(0-1)0 0:Off Load 1:On Load 3 Cycle Selection(0-2)0 0:Monthly 1:Weekly 2:Daily 4 Time(Month)(14095)409

50、5 Bit0:Jan.Bit1:Feb.Bit2:Mar.Bit3:Apr.Bit4:May Bit5:June Bit6:July Bit7:Aug.Bit8:Sep.Bit9:Oct.Bit10:Nov.Bit11:Dec.5 Time(Day)(131)1 The date of start the genset 6 Time(Week)(1-127)1 Bit0:Sunday Bit1:Monday Bit2:Tuesday Bit3:Wednesday Bit4:Thursday Bit5:Friday No.Item Range Default Description Bit6:S