2022年SH3501-2002 石油化工有毒可燃介质管道工程施工及验收规范双语版.doc

《2022年SH3501-2002 石油化工有毒可燃介质管道工程施工及验收规范双语版.doc》由会员分享，可在线阅读，更多相关《2022年SH3501-2002 石油化工有毒可燃介质管道工程施工及验收规范双语版.doc（64页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、备案号：J2492003 SH中华人民共和国石油化工行业标准Standard for Petrochemical Industry of PRCSH 35012002代替SH 35012001SH 3501-2002A substitute version of SH 3501-2001石油化工有毒、可燃介质管道工程施工及验收标准Specification for construction and acceptance of hypertoxic and combustible medium piping engineering in petrochemical industryChinese

2、 language is the original language and if inconsistencies exist between English and Chinese versions, the Chinese version takes precedence and the Chinese version is the legally binding version. 本来以中文书就，假如英文和中文版本之间存在不一致，以中文版本为准，中文版本具有法律约束力。20030209 发布20030501 施行国家经济贸易委员会发布Issued on Feb. 9, 2003 Impl

3、emented on May 1, 2003Issued by State Economy Trade Commission59SH 35012002目次List of Contents前言Foreword1范围Scope2标准性援用文件Normative documents quoted3总则General4管道分级Pipeline grading5管道组成件检验Inspection of constituent elements of pipeline5.1一般规定General specifications5.2管子检验Inspection of pipe5.3阀门检验Inspectio

4、n of valve5.4其他管道组成件检验Inspection of constituent elements of other pipes6管道预制及安装Prefabrication and installation of pipeline6.1管道预制Prefabrication of pipeline6.2管道安装Installation of pipeline7管道焊接Welding of pipeline7.1一般规定General specifications7.2焊前预备与接头组对Preparation and assembly of joints7.3焊接工艺要求Requir

5、ement for welding procedure7.4预热与热处理Preheating and heat treatment7.5质量检验Quality inspection8管道系统试验Test for piping system8.1管道系统压力试验Pressure test for piping system8.2管道系统吹扫Sweeping for piping system8.3气体泄漏性试验及真空度试验Gas leakage test and test of vacuum degree9交工文件Handover document附录A（材料性附录）常用有毒介质、可燃介质App

6、endix A (Data Appendix) Common Hypertoxic and Combustible Medium附录B（材料性附录）焊接接头坡口方式及组对要求Appendix B(Data Appendix) Type of Groove of Weld Joint and Requirements for Assembly附：条文说明Explanation to Clauses前言Foreword本标准是依照国经贸厅行业200236号文的通知，由中国石化集团第五建立公司对石油化工剧毒、可燃介质管道工程施工及验收标准SH 35012001进展修订而成。The Specifica

7、tion is the revision of Specification for Construction and Acceptance of Hypertoxic and Combustible Medium Piping Engineering in Petrochemical Industry SH3501-2001 revised by The Fifth Construction Company of the China Petrochemical Corporation according to File 200236 issued by State Economy Trade

8、Commission.本标准共分9章和2个材料性附录。本标准与SH 35012001石油化工剧毒、可燃介质管道工程施工及验收标准相比，主要变化如下：The Specification contains 9 chapters and 2 data appendixes. The main changes of the Specification comparing with original SH3501-2001 Specification for Construction and Acceptance of Hypertoxic and Combustible Medium Piping E

9、ngineering in Petrochemical Industry are:适用范围扩大至毒性程度为中度危害和轻度危害介质；调整了管道分级规定，与SH 35092001石油化工管道设计器材选用通则协调一致；将有关内容与GB 5023597工业金属管道工程施工及验收标准进展了协调；修正了原标准中管道组成件检验、试验的有关规定；完善了焊接接头检验方面的有关规定。-Scope of application is enlarged. Toxic level includes moderate hazard and negligible hazard.-Specification for pipe

10、line grading is regulated to comply with General Rule for Pipeline Design and Selection in Petrochemical Industry.-Specification for inspection and test of constituent elements of pipeline is modified.-Perfect specification for inspection of weld joint.本标准以黑体字标志的条文为强迫性条文，必要严格执行。Boldfaces in the Spec

11、ification are mandatory clauses and must be strictly implemented.本标准由中国石化集团施工标准治理站淄博分站治理，由中国石化集团第五建立公司负责解释。The Specification is managed by Zibo Branch of Construction Specification Management Station of China Petrochemical Corporation, and interpreted by The Fifth Construction Company of the China P

12、etrochemical Corporation. 本标准在施行过程中，如发觉需要修正补充之处，请将意见和有关材料提供应我们，以便今后修订时参考。In case any repair and supplement are found necessary during implementation of the Specification, please send the suggestion together with relevant information to us for reference during future update.治理单位：中国石化集团公司施工标准治理站淄博分站Ma

13、nagement unit: Zibo Branch of Construction Specification Management Station of China Petrochemical Corporation通讯地址：山东省淄博市132号信箱Address: Mailbox No. 132, Zibo City, Shandong Province.邮政编码：255438 Postcode: 255438 主编单位：中国石化集团第五建立公司Chief editor: China Petrochemical Corporation通讯地址：甘肃省兰州市西固区康乐路35号Address

14、: No. 35, Kangle Rd., Xigu District, Lanzhou City, Gansu Province邮政编码：730060 Postcode: 730060主要起草人：姚代贵张西庚汪庆华单承家Main drafters：Yao Daigui, Zhang Xigeng, Wang Qinghua, Shan Chengjia本标准1985年发布，1997年第一次修订，2001年第二次修订，本次为第三次修订。The specification was issued in 1985, revised in 1997 for the first time, revise

15、d in 2001 for the second time, and this is the third revision.石油化工有毒、可燃介质管道工程施工及验收标准Specification for Construction and Acceptance of Hypertoxic and Combustible Medium Piping Engineering in Petrochemical Industry1范围Scope本标准规定了石油化工有毒（毒性程度为极度危害、高度危害、中度危害和轻度危害）、可燃介质管道工程的施工和检验要求。The Specification specifi

16、es requirements for construction and inspection of hypertoxic (toxic levels are utmost hazard, high hazard, moderate hazard and negligible hazard) and combustible medium piping engineering.本标准适用于设计压力400 Pa绝压42MPa表压，设计温度196850的有毒、可燃介质钢制管道工程的施工及验收。The Specification is applicable for construction and a

17、cceptance of hypertoxic and combustible medium steel piping engineering with design pressure of 400Pa absolute pressure42MPa gage pressure and design temperature of -196850.本范围不适用于长输管道及城镇公用燃气管道的施工及验收。The Specification is not applicable for construction and acceptance of long-distance pipeline and ga

18、s pipeline.2标准性援用文件Normative documents quoted以下文件中的条款通过本标准的援用而成为本标准的条款。但凡注日期的援用文件，其随后所有的修正单（不包括堪误的内容）或修订版均不适用于本标准，然而，鼓舞依照本标准达成协议的各方研究是否可使用这些文件的最新版本。但凡不注日期的援用文件，其最新版适用于本标准。Provisions in following documents are quoted as provisions of the Specification. Modification (excluding corrigendum) or revision

19、 of dated document is not applicable for the Specification. It is suggested that all parties who reach an agreement based upon the Specification can study whether the latest revision of the dated document can be used. Latest revision of undated document is applicable for the Specification.GB 4159金属低

20、温夏比冲击试验方法Test Methods for Low Temperature Variation Ratio Impact of MetalGB/T 4334.16不锈钢耐腐蚀试验方法Test Method for Anticorrosion of Stainless SteelGB 5777无缝钢管超声波探伤方法Methods for Supersonic Inspection of Seamless Steel PipeJB 4730压力容器无损检测Nondestructive Test of Pressure ContainerSH 3503-2001石油化工工程建立交工技术文件规

21、定Specifications for Technical Document of Handover of Petrochemical Engineering ConstructionSH3059-2001石油化工管道设计器材选用通则General Rule for Pipeline Design and Selection in Petrochemical IndustrySH 3064石油化工钢制通用阀门选用、检验及验收Selection, Inspection and Acceptance of Common Steel Valve in Petrochemical IndustrySH

22、 3505石油化工施工平安技术规程Specifications for Safety Technology of Construction in Petrochemical IndustrySH3521石油化工仪表工程施工技术规程Technical Specifications for Construction of Meter Works in Petrochemical IndustrySH 3526石油化工异种钢焊接规程Specifications for Welding of Special Steel in Petrochemical Industry国质检锅2002109号GZJG

23、 2002 No. 109锅炉压力容器压力管道焊工考试与治理规则Rules for Examination and Management of Welder for Welding of Pressure Container and Pipe of Boiler劳部发1993441号LBF 1993 No. 441锅炉压力容器无损检测人员资历考核规则Rules for Qualification Test of Operator for Nondestructive Test of Pressure Container of Boiler3总则General3.1 有毒、可燃介质管道施工应按设

24、计文件规定进展，修正设计或材料代用，应经设计单位批准。3.1 Construction of hypertoxic and combustible medium piping shall be carried out as per specifications in design document. Modification of design or replacement of material shall be approved by the design unit.3.2管道施工的平安技术和劳动保护，应按SH 3505的规定执行。在已投入消费的区域内施工时，应按消费区域的特点制定施工平安

25、技术措施。3.2 Safety technique and labor protection for piping installation shall be implemented according to SH 3505. If construction is carried out in producing area, measures for safety technique of construction shall be formulated according to characteristics of the producing area.3.3承担有毒、可燃介质管道施工的单位

26、，必须持有质量技术监视行政部门颁发的相应的压力管道安装许可证。3.3 Unit undertaking construction of hypertoxic and combustible medium piping must have corresponding certificate of pressure piping installation issued by Executive of Quality Technology Supervision.3.4从事有毒、可燃介质管道施工的焊工应按锅炉压力容器压力管道焊工考试与治理规则进展考试，获得合格证书。无损检测人员应按锅炉压力容器无损检

27、测人员资历考核规则进展考核，获得相应的资历证书。3.4 Welder engaged in hypertoxic and combustible medium piping installation shall take an examination for Rules for Examination and Management of Welder for Welding of Pressure Pipe of Boiler and get the certificate of qualification. Nondestructive test operator shall take an

28、 examination for Rules for Qualification Test of Operator for Nondestructive Test of Pressure Container of Boiler and get the certificate of qualification.4管道分级Pipeline grading4.1输送有毒、可燃介质管道的分级，应符合SH 30592001的规定（见表1）。常见毒性介质、可燃介质参见附录A。4.1 Grading of pipeline conveying hypertoxic and combustible mediu

29、m shall meet specifications in SH 30592001 (see table 1). Please see Appendix A for common hypertoxic and combustible medium.表1管道分级Table 1 Pipeline Grading管道级别Pipeline grading适用范围Scope of applicationSHA1毒性程度为极度危害介质管道（苯管道除外）2 毒性程度为高度危害介质的丙烯腈、光气、二硫化碳和氟化氢介质管道3 设计压力大于或等于10.0MPa输送有毒、可燃介质管道1. Utmost hazar

30、d pipeline (except benzene pipeline)2. Acrylon, carbonyl chloride, carbon disulfide and hydrogen fluoride medium pipeline whose toxic level is high hazard3. Pipeline conveying hypertoxic and combustible medium with design pressure 10.0MPaSHB1 毒性程度为极度危害介质的笨管道2 毒性程度为高度危害介质管道（丙烯腈、光气、二硫化碳和氟化氢管道除外）3 甲类、乙

31、类可燃气体和甲A类液化烃、甲B类、乙A类可燃液体介质管道1. Utmost hazard benzene pipeline2. High hazard medium pipeline (except Acrylon, carbonyl chloride, carbon disulfide and hydrogen fluoride pipeline)3. Category A and B combustible gas and Category AB and BA combustible liquid medium pipelineSHC1 毒性程度为中度、轻度危害介质管道2 乙B类、丙类可燃

32、液体介质管道1. Moderate and negligible hazard medium pipeline2. Category BB and C combustible liquid medium pipelineSHD设计温度低于-29的低温管道Pipeline with design temperature lower than -294.2 输送同时具有毒性和可燃特性介质的管道，应按本标准中的高级别管道处理。4.2Pipeline conveying both hypertoxic and combustible medium shall be treated as high-le

33、vel pipeline in the Specification.4.3 输送混合介质的管道，应以主导介质作为管道分级的依照。4.3Pipeline conveying mixed medium shall take dominant medium as grading reference.5 管道组成件检验 Inspection of constituent elements of pipeline5.1一般规定 General specifications5.1.1有毒、可燃介质管道工程使用的管道组成件，应符合设计文件规定及本标准的有关要求。5.1.1 Constituent eleme

34、nts of pipeline for Hypertoxic and Combustible Medium Piping Engineering shall meet the requirements in design document and the Specification.5.1.2管道组成件（管子、阀门、管件、法兰、补偿器、平安保护装置等）的制造单位，当所在地质量技术监视行政部门有规定时，应获得压力管道元件制造单位平安注册证书。5.1.2Manufacturer of constituent elements of pipeline (pipe, valve, pipe fitti

35、ngs, flange, compensator, safety protection device, etc.) shall have Registered Certificate of Manufacturer for Safety Production of Elements of Pressure Pipe if it is required by local executive of quality technology supervision.5.1.3管道组成件必须具有质量证明文件，无质量证明文件的产品不得使用。5.1.3 Constituent elements of pipe

36、line must have certificate of qualification. Product having no the certificate cant be adopted.产品在使用前，应对质量证明文件进展审查，并与实物核对。假设到货的管道组成件实物标识不清或与质量证明文件不符或对产质量量证明文件中的特性数据或检验结果有异议，供货方应按相应标准作验证性检验或追溯到产品制造单位。异议未处理前，该批产品不得使用。Certificate of qualification of products shall be checked before use. If marks of the

37、 constituent elements are unclear, or not conform to certificate of qualification, or there is objection about performance data or inspection result in certificate of qualification, the Supplier shall carry out experimental verification based upon related standard or track back to the manufacture. B

38、efore settlement of objection, the products cant be used.5.1.4管道组成件在使用前应进展外观检查，其外表质量应符合相应产品标准的规定，不合格者不得使用。5.1.4 Appearance inspection of constituent elements of pipeline shall be carried out before use. Quality of their surfaces shall meet the specification in corresponding standard. Unqualified pro

39、duct cant be used.5.1.5合金钢管道组成件主体的关键合金成分，应依照本标准规定的比例采纳光谱分析或其他方法进展半定量分析复查，并作好标识。5.1.5 Certain proportion (specified in the Specification) of alloyed steel pipelines main body, alloying component, shall be checked with spectral analysis method or other methods. Marks shall be made.5.1.6设计文件有低温冲击值要求的材料

40、，产质量量证明文件应有低温冲击韧性试验值，否则应按GB 4159的规定进展补项试验。5.1.6 If there are requirements for low temperature impact value of a material in design document, certificate of qualification of the material shall have low temperature impact toughness test value; otherwise, additional test shall be done according to GB 4

41、159.5.1.7凡按规定作抽样检查或检验的样品中，假设有一件不合格，必须按原规定数加倍抽检，假设仍有不合格，则该批管道组成件不得使用，并应作好标识和隔离。5.1.7 If one of samples is unqualified during sampling inspection, certain amount (specified in the Specification) of products shall be inspected. If there still is unqualified product, the batch of products cant be used.

42、And they shall be marked and separated with other products.5.1.8管道组成件应分区存放，且不锈钢管道组成件不得与非合金钢、低合金钢接触。5.1.8 Constituent elements of pipeline shall be stacked by areas. Constituent elements of stainless steel pipeline cant contact non-alloyed steel and low alloy steel.5.2管子检验Inspection of pipe5.2.1输送有毒、

43、可燃介质的管子，使用前应按设计文件要求核对管子的规格、数量和标识。5.2.1 Specification, quantity and mark of pipe conveying hypertoxic and combustible medium shall be checked according to the design document.5.2.2管子的质量证明文件应包括以下内容：5.2.2Certificate of Qualification of pipe shall contain following contents:a) 产品标准号；a) Product standard

44、number of product;b) 钢的牌号；b) Brand of steel;c) 炉罐号、批号、交货状态、重量和件数；c) Stove number, lot number, delivery state, weight and number of packages;d) 品种名称、规格及质量等级；d) Name, specification and quality level of variety;e) 产品标准和订货合同中规定的各项检验结果；e) Results of all inspections specified in product standard and contract;f) 制造厂检验印记。f) Inspection stamp of manufacturer.5.2.3假设到货管子钢的牌号、炉罐号、批号、交货状态与质量证明文件不符，该批管子不得使用。5.2.3 If brand, stove number,