模具术语相关翻译.doc

《模具术语相关翻译.doc》由会员分享，可在线阅读，更多相关《模具术语相关翻译.doc（5页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、模具,冲压相关英语专业翻译 模具工程常用词汇 金属弹片(锅仔片)，metal dome.die 模具 figure file, chart file图档 cutting die, blanking die冲裁模 progressive die, follow (-on)die 连续模 compound die复合模 punched hole冲孔 panel board镶块 to cut edges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸 Line strenching, line pulling线拉伸 engraving

2、, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper paddin

3、g plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 plain die简易模 pierce die冲孔模 forming die成型模 progressive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce冲孔 forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点 dome凸圆 semi-shearing半剪 tamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side str

4、etch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark farside反面压印 冲压名称类 stamping, press冲压 punch press, dieing out press冲床 uncoiler & strainghtener整平机 feeder送料机 rack, shelf, stack料架 cylinder油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输

5、送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤 deformation变形 filings铁削 to draw holes抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取 approval examine and ver

6、ify审核 processing, to process加工 delivery, to deliver 交货 to return delivenry to.to send delinery back to retrn of goods退货 registration登记 registration card登记卡 to control管制 to put forward and hand in提报 safe stock安全库存 acceptance = receive验收 to notice通知 application form for purchase请购单 consume, consumptio

7、n消耗 to fill in填写 abrasion磨损 reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics统计 demand and supply需求 career card履历卡 to take apart a die卸下模具 to load a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓 to move away a die plate移走模板 easily damaged parts易损件 sta

8、ndard parts标准件 breaking.(be)broken,(be)cracked 断裂 to lubricate润滑 common vocabulary for die engineering extension dwg展开图 o procedure dwg工程图 o die structure dwg模具结构图 o material材质 o material thickness料片厚度 o factor系数 o upward向上 o downward向下 o press specification冲床规格 o die height range适用模高 o die height闭模

9、高度 o burr毛边 o gap间隙 o weight重量 o total wt.总重量 o punch wt.上模重量机械模模具术语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate 水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(

10、full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold

11、二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,retur

12、n core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lev

13、er arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术

14、语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use

15、(core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极)：copper electrode 塑胶产品负面描述的英文词汇blister 起泡

16、blooming 起霜 blow hole 破孔 blushing 泛白 body wrinkle 侧壁皱纹 breaking-in 冒口带肉 bubble 膜泡 burn mark 糊斑 burr 毛边 camber 翘曲 cell 气泡 center buckle 表面中部波皱 check 细裂痕 checking 龟裂 chipping 修整表面缺陷 clamp-off 铸件凹痕 collapse 塌陷 color mottle 色斑 corrosion 腐蚀 crack 裂痕 crazing 碎裂crazing 龟裂 deformation 变形 edge 切边碎片 edge crac

17、k 裂边 fading 退色 filler speak 填充料斑 fissure 裂纹 flange wrinkle 凸缘起皱 flaw 刮伤 flow mark 流痕 galling 毛边 glazing 光滑 gloss 光泽 grease pits 污斑 grinding defect 磨痕 haircrack 发裂 haze 雾度 incrustation 水锈 indentation 压痕 internal porosity 内部气孔 mismatch 偏模 mottle 斑点 necking 缩颈 nick 割痕 orange peel 橘皮状表面缺陷 overflow 溢流 pe

18、eling 剥离 pit 坑 pitting corrosion 点状腐蚀 plate mark 模板印痕 pock 麻点 pock mark 痘斑 resin streak 树脂流纹 resin wear 树脂脱落 riding 凹陷 sagging 松垂 saponification 皂化 scar 疤痕 scrap 废料 scrap jam 废料阻塞 scratch 刮伤/划痕 scuffing 深冲表面划伤 seam 裂痕 shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔 sink mark 凹痕 skin inclusion 表皮折迭

19、straightening 矫直 streak 条状痕 surface check 表面裂痕 surface roughening 橘皮状表皮皱折 surging 波动 sweat out 冒汗 torsion 扭曲 warpage 翘曲 waviness 波痕 webbing 熔塌 weld mark 焊痕 whitening 白化 wrinkle 皱纹missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to stand

20、ard不合规格 dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属) flash(塑件)毛边 poor staking铆合不良excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 (Flow Line)流痕 (Weld Line) 熔接线 Sink Mark凹陷 Streak条纹 Warpage翘曲5