模具专业术语—英文.xls

《模具专业术语—英文.xls》由会员分享，可在线阅读，更多相关《模具专业术语—英文.xls（6页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、模芯Parting Core平面度Parallel局部视图Partial View倒角Chamfer冷料#Cold Slag模胚Mold Base线切割Wire cutting热嘴Hot nozzle轮廊Contour火花加工E.D.M螺纹孔Tapping Hole熔接线Weld line连接件Fittings压力Press斜针Angle Pin晒纹Texturing接合Engage梯形Trapezoid替换镶件Interchangeable Mold Inserts凸缘、法兰Flange指定吨位的注塑机Specific Press方铁Spacer Block水嘴接头Cooling Nippl

2、e顶针板Ejector Plate吊模孔Eyebolt Thread顶针面板Ejector Retainer Plate回针Return Pin垫板Support Plate二级顶出针Sub-Leaderd Pin后模镶针Core Pin镶件Mold Insert拉圾钉Stop Pin加硬Harden有托顶针Shoulder Ejector Pin唧嘴Sprue Bushing顶针板导套Ejector Guide Bushing设计简图Design Preliminary针板导柱Ejector Guide Pin名细表Title Block唧嘴Sprue Bushing版本标识Revision

3、 Level三板模延伸式唧嘴Extension Nozzle Bushing材料清单BOM水口板导套Runner Stripper Plate Bushing制模Build Mold定位圈（法兰）Locating Ring手动滑块Hand Slide管钉（定位销）Dowel Pin漏水测试Leak Test管状管钉Tubular Dowel流道排气Runner Venting吊环Lifting Ring抛光 Polishing日期印Dating Insert侧抽芯Side Action环保印Recycling Insert加强筋Reinforcing气顶Air Poppet Valve三角撑G

4、usset截水口镶件Runner Shut-Off Insert柱子Boss早回Early Ejector Return出模斜度Draft加速项Accelerated Ejector外廊Contour客户Client落单会议Kick-Off Meeting产品名Part Name装卸孔Handling Hole产品编号Part No运输安全带Mold strap收缩量Shrinkage码模槽Clamp Slot版本Rev撑头Support Pillar模胚Mold Base螺牙1/2-13Eye Bolt 1/2-13Tap下模镶件Core Block导柱位Leader Pin Locatio

5、n上模镶件Cavity Block耐落胶Teflon Paste小镶件Sub-Insert偏移量Offset下模小镶件Core Sub-Insert水塞Water Line Plug上模小镶件Cavity Sub-Insert撬模槽Entry Slot行位Slide重新加工Reworked行位镶件Slide Insert配件Components压条Guide strip补偿Compensation压紧块（铲机）Wedge硬片（摩擦片）Wear Plate合模Shutoff水口铁Runner Bar空隙槽Clearance Slot上模水口铁Upper Runner Bar导柱及导套Leader

6、 Pin&Guide Bushing下模水口铁Lower Runner Bar水口拉钩Spuer Puller弹簧Spring模框镶件Pocket Insert水口勾针Sprue Puller Pin成型热固性塑胶模具Thermoset Mold顶针Ejector Pin三板模3-Plat Mold撑头Support Pillar分型线Parting Line直身锁Side Lock司筒Ejector Sleeve斜度锁Interlock垫圈Washer锁模板Safety Bar熔接线（夹水纹）Weld lineO令（密封圈）ORing吸针Sucker Pin喉塞Plug回针板Retainer

7、 Plate隔水片Baffle顶出板Knock-Out Plate波子螺丝（行位定位螺丝）Ball-Catch(Spring Plunger)电动安全开关Electrical-Safety Switch斜顶Lifter脱开Cut Of Position控制开关Switch预先决定Preload回针Return Pin缓冲器Bumper斜导柱Angle Pin衬垫Cushion推板Stripper Plate公差ToleranceA板APlate突然性动作SlamB板BPlate销针Dowel方铁（垫铁）Spacer Block沟槽Groove顶针板Ejector Plate精磨Finished

8、顶针面板Ejector Retainer Plate通框Through Window垫板Support Plate粘后模Sticking Core垃圾钉Stop Pin粘水口Sticking Sprue有托顶针Shoulder Ejector Pin夹水纹Weld Line顶针板导套Ejector Guide Bushing变形Warpage针板导柱Ejector Guide Pin走水不平均Filling Uneven唧嘴Sprue Bushing走不齐Short Shot三板模延伸式唧嘴Extension Nozzle Bushing挂成品Part Hanging水口板导套Runner S

9、tripper Plate Bushing漏水Water Leakage定位圈（法兰）Locating Ring刮花（擦伤）scratch管钉（定位销）Dowel Pin漏电Ele Leakage管状管钉Tubular Dowel困气Air Trapping吊环Lifting Ring温度Temperature日期印Dating Insert注塑模Injection Mold环保印Recycling Insert入水Gate气顶Air Poppet Valve试板Sampling截水口镶件Runner Shut-Off Insert压力Pressure早回Early Ejector Retur

10、n倒圆Fillet加速顶Accelerated Ejector顶棍Ejector Rod扁顶Ejector Blade顶白Stress Mark出模斜波Draft粘前模Sticking Cav手动滑块模具Hand Slide-In Type Mold名细表Title Block回针板Return Pin版本标识Revision Level材料清单Stock List二级顶出针Sub-Leader Pin斜导柱（斜边）Angle Pin镶件Mold InsertA板 Aplate锁定位LockB板 Bplate楔子(铲鸡)Wedge倒扣Under-Cut高产量模量High Volume Runn

11、ing Mold披峰Flash剖面图Cross Section缩水Sink Mark模具结构Mold Construction氮化Nitride模芯Parting Core不规则四边形Trapezoid局部视图Partial View收缩量Shrinkage热流道Manifold连续的Consecutive热嘴Hot Nozzle雕刻Engrave型腔数Cavity No出模角Draft模号Mold No分模面Parting Surface胶料Material擦位Shut-Off(S/0)尺寸Dimension导套Guide Bushing重要尺寸Critical Dimension回针Ret

12、urn Pin雕刻Engrave加硬Harden托司 EJ.GUIDE PIN唧嘴Sprue Bushing油缸Hydraulic Cylinder设计简图Design Preliminary司筒Ejector Sleeve丝印Silk print导柱Leader Pin不干胶Adhesive Sticker冷料#Cold Slag导向针Guide Pin线切割Wire Cutting公差Tolerance轮廓Contour线切割Wire Cutting螺纹孔Tapping Hole电火花E.D.M连接件 Fittings抛光Polishing斜针Angle Pin蚀纹Texture接合Eng

13、age探热针Thermocouple替换镶件Interchangeable Mold Inserts塞打螺丝（限螺丝）Puller Bolt指定吨位的注塑机Specific Press盖板Cover Plate水嘴接头Cooling Nipple齿轮Gear吊模孔Eyebolt Thread回针Return PinSurface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Bloomin

14、g/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡Void 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2Poor dispersion 分散不好FR/PTFE agglomerates etc 阻燃剂/PTFE结块Pellet porous 粒子不密/蜜蜂窝Low i

15、mpact/tensile etc 物理性能低High flow/filler content etc 流动性/填充过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimen

16、sion 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfid

17、e/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra 添加多一点Reduced content 减少含量Dropped/reduced by x 减少含量Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by 预计在完成Expected order is xMT 预计定单量吨Estimated annual/monthly consumption 预计年/月用量