《光模块手册.pdf》由会员分享,可在线阅读,更多相关《光模块手册.pdf(12页珍藏版)》请在淘文阁 - 分享文档赚钱的网站上搜索。
1、 Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 1/12 Rev.3.4 6 6GG S SF FP P+T Tr ra an ns sc ce ei iv ve er r MMT TR RS S-6 6E E3 31 1-0 01 1 Description MTRS-6E31-01 is a high performance,cost effective modules,which is supporting Multi Rate 1.25-8.6Gbps,and transmission distance up
2、to 10km on SM fiber.The transceiver consists of two sections:The transmitter section incorporates a 1310nm DFB driver and re-timer.The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier(TIA).The module is hot pluggable into the 20-pin connector.The high-speed
3、 electrical interface is base on low voltage logic,with nominal 100 Ohms differential impedance and AC coupled in the module.The optical output can be disabled by LVTTL logic high-level input of TX_DIS.Transmit Fault(Tx_Fault)is provided to indicate that the module transmitter has detected a fault c
4、ondition related to laser operation or safety.Loss of signal(RX_LOS)output is provided to indicate the loss of an input optical signal of receiver.A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire SFP Management Interface.This i
5、nterface uses a single address,A0h,with a memory map divided into a lower and upper area.Basic digital diagnostic(DD)data is held in the lower area while specific data is held in a series of tables in the high memory area.Features Up to 10KM transmission distance Support Multi Rate 1.25-8.6Gbps 1310
6、nm DFB and PIN receiver SFI electrical interface 2-wire interface for integrated Digital Diagnostic monitoring SFP+MSA package with duplex LC connector Hot pluggable Very low EMI and excellent ESD protection +3.3V power supply Power consumption less than 1W Operating case temperature:-40+85C Applica
7、tions High-speed storage area networks Computer cluster cross-connect Custom high-speed data pipes LTE optical repeater application Compliance Compliant with Fiber Channel(FC)-Standard INCITS 352 Compliant with IEEE 802.3ae-2002 Compliant with FCC 47 CFR Part 15,Class B Compliant with FDA 21 CFR 104
8、0.10 and 1040.11,Class I except for deviations pursuant Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 2/12 Rev.3.4 Specification Absolute Maximum Ratings Parameter Symbol Min.Max.Unit Storage Temperature TS-40+85 Supply Voltage VCC3 0 3.6 V Relative Humidity RH 5+95%RX Input Average P
9、ower Pmax-3 dBm Recommended Operating Conditions Parameter Symbol Min.Typical Max.Unit Operating Case Temperature TC-40 25+85 VCC3 3.13 3.3 3.47 V Power Supply Voltage ICC3 300 mA Power Dissipation PD 1 W Data Rate 8.6 Gbps Transmission Distance 10 Km Transmitter Operating Characteristic-Optical,Ele
10、ctrical Parameter Symbol Min.TypicalMax.Unit Note Spectral Width(-20dB)Pm-1 nm Side Mode Suppression Ratio SMSR 35-dBm Laser Off Power Poff-30 dBm Extinction Ratio ER 3.5-dB Transmitter Dispersion Penalty TDP-3.2 dB Relative Intensity Noise Rin-128 dB/Hz Optical Return Loss Tolerance 12-dB Operating
11、 Data Rate 8.6 Gbps Centre Wavelength C 1260 1310 1355 nm Note1 Average Optical Power Pavg-8.2-0.5 dBm Note1 Optical Eye Mask Compliant with IEEE 802.3ae Note2 Single Ended Output Voltage Tolerance -0.3 4 V Common mode voltage tolerance 15 -mV Tx Input Diff Voltage VI 180 700 mV Tx Fault VoL-0.3 0.4
12、 V At 0.7mA Data Dependent Input Jitter DDJ 0.1 UI Data Input Total Jitter TJ 0.28 UI Notes:1 Average optical power shall be measured using the methods specified in TIA/EIA-455-95.2 Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivi
13、ty.They are not the required characteristic of the receiver.Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 3/12 Rev.3.4 Receiver Operating Characteristic-Optical,Electrical Parameter SymbolMin.Typ.Max.Unit Note Center Wavelength r 1260 1310 1360 nm Receiver Sensitivity(OMA)Psens -14.4
14、dBm Stressed Sensitivity(OMA)-12.6 dBm Los Assert LosA-30 -dBm Los Dessert LosD -16 dBm Los Hysteresis LosH 0.5 -dB Overload Pin 0.5 dBm Stressed Eye Jitter 0.3 UIp-p Note1 Receive electrical 3dB upper cutoff frequency 12.3 GHz Vertical Eye Closure Penalty 2.2 dB Note2 Receiver Reflectance -12 dB Op
15、erating Data Rate 8.6 Gbps Single Ended Output Voltage Tolerance -0.3 4 V Rx Output Diff Voltage Vo 450 850 mV Rx Output Rise and Fall Time Tr/Tf 30 ps 20%to 80%Total Jitter TJ 0.7 UI Deterministic Jitter DJ 0.42 UI Notes:1 Receiver sensitivity is informative.Stressed receiver sensitivity shall be m
16、easured with conformance test signal for BER=1x 10-12.2 Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity.They are not the required characteristic of the receiver.Control and Status I/O Timing Characteristics Parameter Symbol Min
17、.Max.Unit Note TX Disable Assert Time t_off 10 s Note1 TX Disable Negate Time t_on 1 ms Note2 Time to initialize including reset of TX_Fault t_init 300 ms Note3 TX Fault Assert Time t_fault 100 s Note4 TX Disable to reset t_reset 10 s Note5 LOS Assert Time t_loss_on 100 s Note6 LOS Deassert Time t_l
18、oss_off 100 s Note7 Rate-Select Change Time t_ratesel 10 s Note8 Serial ID Clock Rate f_serial_clock 100 kHz Notes:1 Time from rising edge of TX Disable to when the optical output falls below 10%of nominal 2 Time from falling edge of TX Disable to when the modulated optical output rises above 90%of
19、nominal Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 4/12 Rev.3.4 3 From power on or negation of TX Fault using TX Disable 4 Time from fault to TX fault on 5 Time TX Disable must be held high to reset TX_fault 6 Time from LOS state to RX LOS assert 7 Time from non-LOS state to RX LOS
20、 deassert.8 Time from rising or falling edge of Rate Select input until receiver bandwidth is in conformance with appropriate specification Optical Characteristics(Multi Rate Characteristics)Parameters 1.25G1 2.5G 4.95G Total Power Consumption1W 1W -8.2-8.2-8.2 Extinction Ratio 3.5 3.5 3.5 Eye Mask
21、Margin 20%20%20%Rx Sensitivity-22.0dBm-20.0dBm-17.0dBm Working Temperature-40+85C-40+85C-40+85C Notes:1 For 1.25G data rate,the modules performance is compatible with 1G FC application but not fully compliant.If customer needs to fully compliant with 1.25G data rate specifications,we need to impleme
22、nt“Rate-Selection”function,please contact our sales team for detailed information.Pin-out Definition Figure1 Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 5/12 Rev.3.4 Pin Assignment Pin Logic Symbol Name/Description Note 1 VeeT Module Transmitter Ground Note1 2 LVTTL-O TX_Fault Modul
23、e Transmitter Fault Note2 3 LVTTL-I TX_Disable Transmitter Disable;Turns off transmitter laser output Note3 4 LVTTL-I/O SDA 2-wire Serial Interface Data Line(Same as MOD-DEF2 as defined in the INF-8074i)Note4 5 LVTTL-I/O SCL 2-wire Serial Interface Clock(Same as MOD-DEF1 as defined in the INF-8074i)
24、Note4 6 MOD_ABS Module Absent,connected to VeeT or VeeR in the module Note5 7 LVTTL-I RS0 Not used 8 LVTTL-O RX_LOS Receiver Loss of Signal Indication(In FC designated as RX_LOS,in SONET designated as LOS,and in Ethernet designated at Signal Detect)Note2 9 LVTTL-I RS1 Not used 10 VeeR Module Receive
25、r Ground Note1 11 VeeR Module Receiver Ground Note1 12 CML-O RD-Receiver Inverted Data Output 13 CML-O RD+Receiver Non-Inverted Data Output 14 VeeR Module Receiver Ground Note1 15 VccR Module Receiver 3.3 V Supply 16 VccT Module Transmitter 3.3 V Supply 17 VeeT Module Transmitter Ground Note1 18 CML
26、-I TD+Transmitter Non-Inverted Data Input 19 CML-I TD-Transmitter Inverted Data Input 20 VeeT Module Transmitter Ground Note1 Notes:1 The module signal ground pins,VeeR and VeeT,shall be isolated from the module case.2 This pin is an open collector/drain output pin and shall be pulled up with 4.7k-1
27、0kohms to Host_Vcc on the host board.Pull ups can be connected to multiple power supplies,however the host board design shall ensure that no module pin has voltage exceeding module VccT/R+0.5 V.3 This pin is an open collector/drain input pin and shall be pulled up with 4.7k-10kohms to VccT in the mo
28、dule.4 See sff-8431 4.2 2-wire Electrical Specifications.5 This pin shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board.Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 6/12 Rev.3.4 Block Diagram of Transceiver Figure2 Transmitter Section The transmitter converts 6.25Gbit/
29、s serial PECL or CML electrical data into serial optical data compliant with the 6GBASE-LR standard.An open collector compatible Transmit Disable(Tx_Dis)is provided.A logic“1,”or no connection on this pin will disable the laser from transmitting.A logic“0”on this pin provides normal operation.The tr
30、ansmitter has an internal automatic power control loop(APC)to ensure constant optical power output across supply voltage and temperature variations.An open collector compatible Transmit Fault(Tx_Fault)is provided.TX_Fault is a module output contact that when high,indicates that the module transmitte
31、r has detected a fault condition related to laser operation or safety.The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 k.TX_Disable is a module input contact.When TX_Disable is asserted high or left open,the
32、 SFP+module transmitter output shall be turned off.This contact shall be pulled up to VccT with a 4.7 k to 10 k resistor Receiver Section The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data.An open collector compatible Loss of Signal is provided.Rx_LOS when high i
33、ndicates an optical signal level below that specified in the relevant standard.The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 k,or with an active termination.Power supply filtering is recommended for both the tr
34、ansmitter and receiver.The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+is installed that the received signal strength is below the specified range.Such an indication typically points to non-installed cables,broken cables,or a disabled,failing or a powered off
35、 transmitter at the far end of the cable.Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 7/12 Rev.3.4 Recommended Interface Circuit Figure3 Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 8/12 Rev.3.4 Dimensions Figure4 Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketge
36、nuine- 9/12 Rev.3.4 Table 1:Key Mechanical Dimensions Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 10/12 Rev.3.4 Digital Diagnostic Memory Map EEPROM Information Field Size Addr.(Bytes)Name of Field Hex Description 0 1 Identifer 03 SFP 1 1 Ext.Identifier 04 SFP function is defined by
37、 serial ID only 2 1 Connector 07 LC Connector 3-10 8 Transceiver 00 Transceiver Codes 11 1 Encoding 06 64B/66B 12 1 BR,Nominal 3F 6250Mb/s 13 1 Rate Identifier 00 Unspecified 14 1 Length(9um)km 0A Transceiver transmit distance,10km 15 1 Length(9um)100m 64 Transceiver transmit distance,10km 16 1 Leng
38、th(50um)10m 00 Transceiver transmit distance 17 1 Length(62.5um)10m00 Transceiver transmit distance 18 1 Length(Copper)00 Not compliant 19 1 Length(50um OM3)00 Not compliant 20-35 16 Vendor name 48 47 20 47 45 4E 55 49 4E 45 20 20 20 20 20 20“HG GENUINE”Vendor Name(ASCII)36 1 Reserved 00 37-39 3 Ven
39、dor OUI 00 00 00 40-55 16 Vendor PN 4D 54 52 53 2D 36 45 3331 2D 30 31 20 20 20 20“MMT TR RS S-6 6E E3 31 1-0 01 1”P Pa ar rt t N No o.(ASCII)56-59 4 Vendor rev 31 2E 30 20“1.0”(ASCII)60-61 2 Wavelength 05 1E Transceiver wavelength 62 1 Reserved 00 Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marke
40、tgenuine- 11/12 Rev.3.4 63 1 CC_BASE AD Check code for Base ID Fields 64-65 2 Options 00 1A TX_DISABLE,TX_FAULT and Loss of Signal implemented.66 1 BR,MAX 00 Not Specified 67 1 BR,MIN 00 Not Specified 68-83 16 Vendor SN SN(Variable)Serial Number of transceiver(ASCII).84-91 8 Date code DC(Variable)Ma
41、nufactory Date Code.92 1 Diagnostic Monitoring Type 68 Digital diagnostic monitoring implemented,“externally calibrated”is implemented 93 1 Enhanced Options F0 Optional Alarm/Warning flags implemented for all monitored quantities,Optional Soft TX_Disable control and monitoring implemented,Optional S
42、oft TX_FAULT monitoring implemented,Optional Soft RX_LOS monitoring implemented 94 1 SFF_8472 Compliance 01 Includes functionality described in Rev9.3 SFF-8472 95 1 CC_EXT CS(Variable)Check sum for Extended ID Field.96-127 32 Vendor Specific Read only Depends on customer information Filled by zero 1
43、28-255 128 Reserved Read only Filled by zero Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- 12/12 Rev.3.4 Ordering Information PackRateTxPoutRxSTopReachOthers MTRS-6E31-01 SFP+6G1310nm DFB-8.20.5dBmPIN-14.4dBm-408510kmDDM/RoHS MTRS-1E21-01 SFP+10G1310nm FP-8.20.5dBmPIN-14.4dBm-40852kmD
44、DM/RoHS MTRS-02X13-G SFP+10G1310nm DFB-8.20.5dBmPIN-14.4dBm07010kmDDM/RoHS MTRS-1E31-01 SFP+10G1310nm DFB-8.20.5dBmPIN-14.4dBm-408510kmDDM/RoHSMTRS-1E20-01 SFP+10G1310nm FP-8.20.5dBmPIN-14.4dBm0702kmDDM/RoHSMTRS-6E21-01 SFP+6G1310nm FP-8.20.5dBmPIN-14.4dBm-40852kmDDM/RoHSMTRS-6E20-01 SFP+6G1310nm FP
45、-8.20.5dBmPIN-14.4dBm0702kmDDM/RoHSMTRS-6E30-01 SFP+6G1310nm DFB-8.20.5dBmPIN-14.4dBm07010kmDDM/RoHSPart No.SpecificationRelated Product Information Contact Information Wuhan Huagong Genuine Optics Technology Co.,Ltd Address:Science&Technology Region of HUST,Donghu High-Tech Zone Wuhan,Hubei Provinc
46、e,430223,China Tel:+86-27-87180102 Fax:+86-27-87180220 Email:marketgenuine- Website:http:/www.genuine- Statement HG Genuine possesses the authority for ultimate explanation of all information contained in this document,which is subject to change without prior notice.All the information was obtained
47、in specific environments;and HG Genuine will not be responsible for verifying the products performance in customers operating environments,neither liable for the performance of users products.All information contained is only for the users reference and shall not be considered as warranted characteristics.HG Genuine will not be liable for damages arising directly or indirectly from any use of the information contained in this document.Publishing Date:2010-01-08 Copyright HG Genuine All Right Reserved
限制150内