2023年土木工程毕业设计外文文献翻译.pdf

《2023年土木工程毕业设计外文文献翻译.pdf》由会员分享，可在线阅读，更多相关《2023年土木工程毕业设计外文文献翻译.pdf（17页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、外文文献翻译 Reinforced Concrete Concrete and reinforced concrete are used as building materials in every country.In many,including the United States and Canada,reinforced concrete is a dominant structural material in engineered construction.The universal nature of reinforced concrete construction stems f

2、rom the wide availability of reinforcing bars and the constituents of concrete,gravel,sand,and cement,the relatively simple skills required in concrete construction,and the economy of reinforced concrete compared to other forms of construction.Concrete and reinforced concrete are used in bridges,bui

3、ldings of all sorts underground structures,water tanks,television towers,offshore oil exploration and production structures,dams,and even in ships.Reinforced concrete structures may be cast-in-place concrete,constructed in their final location,or they may be precast concrete produced in a factory an

4、d erected at the construction site.Concrete structures may be severe and functional in design,or the shape and layout and be whimsical and artistic.Few other building materials off the architect and engineer such versatility and scope.Concrete is strong in compression but weak in tension.As a result

5、,cracks develop whenever loads,or restrained shrinkage of temperature changes,give rise to tensile stresses in excess of the tensile strength of the concrete.In a plain concrete beam,the moments about the neutral axis due to applied loads are resisted by an internal tension-compression couple involv

6、ing tension in the concrete.Such a beam fails very suddenly and completely when the first crack forms.In a reinforced concrete beam,steel bars are embedded in the concrete in such a way that the tension forces needed for moment equilibrium after the concrete cracks can be developed in the bars.The c

7、onstruction of a reinforced concrete member involves building a from of mold in the shape of the member being built.The form must be strong enough to support both the weight and hydrostatic pressure of the wet concrete,and any forces applied to it by workers,concrete buggies,wind,and so on.The reinf

8、orcement is placed in this form and held in place during the concreting operation.After the concrete has hardened,the forms are removed.As the forms are removed,props of shores are installed to support the weight of the concrete until it has reached sufficient strength to support the loads by itself

9、.The designer must proportion a concrete member for adequate strength to resist the loads and adequate stiffness to prevent excessive deflections.In beam must be proportioned so that it can be constructed.For example,the reinforcement must be detailed so that it can be assembled in the field,and sin

10、ce the concrete is placed in the form after the reinforcement is in place,the concrete must be able to flow around,between,and past the reinforcement to fill all parts of the form completely.The choice of whether a structure should be built of concrete,steel,masonry,or timber depends on the availabi

11、lity of materials and on a number of value decisions.The choice of structural system is made by the architect of engineer early in the design,based on the following considerations:1.Economy.Frequently,the foremost consideration is the overall const of the structure.This is,of course,a function of th

12、e costs of the materials and the labor necessary to erect them.Frequently,however,the overall cost is affected as much or more by the overall construction time since the contractor and owner must borrow or otherwise allocate money to carry out the construction and will not receive a return on this i

13、nvestment until the building is ready for occupancy.In a typical large apartment of commercial project,the cost of construction financing will be a significant fraction of the total cost.As a result,financial savings due to rapid construction may more than offset increased material costs.For this re

14、ason,any measures the designer can take to standardize the design and forming will generally pay off in reduced overall costs.In many cases the long-term economy of the structure may be more important than the first cost.As a result,maintenance and durability are important consideration.2.Suitabilit

15、y of material for architectural and structural function.A reinforced concrete system frequently allows the designer to combine the architectural and structural functions.Concrete has the advantage that it is placed in a plastic condition and is given the desired shape and texture by means of the for

16、ms and the finishing techniques.This allows such elements ad flat plates or other types of slabs to serve as load-bearing elements while providing the finished floor and/or ceiling surfaces.Similarly,reinforced concrete walls can provide architecturally attractive surfaces in addition to having the

17、ability to resist gravity,wind,or seismic loads.Finally,the choice of size of shape is governed by the designer and not by the availability of standard manufactured members.3.Fire resistance.The structure in a building must withstand the effects of a fire and remain standing while the building is ev

18、acuated and the fire is extinguished.A concrete building inherently has a 1-to 3-hour fire rating without special fireproofing or other details.Structural steel or timber buildings must be fireproofed to attain similar fire ratings.4.Low maintenance.Concrete members inherently require less maintenan

19、ce than do structural steel or timber members.This is particularly true if dense,air-entrained concrete has been used for surfaces exposed to the atmosphere,and if care has been taken in the design to provide adequate drainage off and away from the structure.Special precautions must be taken for con

20、crete exposed to salts such as deicing chemicals.5.Availability of materials.Sand,gravel,cement,and concrete mixing facilities are very widely available,and reinforcing steel can be transported to most job sites more easily than can structural steel.As a result,reinforced concrete is frequently used

21、 in remote areas.On the other hand,there are a number of factors that may cause one to select a material other than reinforced concrete.These include:1.Low tensile strength.The tensile strength concrete is much lower than its compressive strength(about 1/10),and hence concrete is subject to cracking

22、.In structural uses this is overcome by using reinforcement to carry tensile forces and limit crack widths to within acceptable values.Unless care is taken in design and construction,however,these cracks may be unsightly or may allow penetration of water.When this occurs,water or chemicals such as r

23、oad deicing salts may cause deterioration or staining of the concrete.Special design details are required in such cases.In the case of water-retaining structures,special details and/of prestressing are required to prevent leakage.2.Forms and shoring.The construction of a cast-in-place structure invo

24、lves three steps not encountered in the construction of steel or timber structures.These are(a)the construction of the forms,(b)the removal of these forms,and(c)propping or shoring the new concrete to support its weight until its strength is adequate.Each of these steps involves labor and/or materia

25、ls,which are not necessary with other forms of construction.3.Relatively low strength per unit of weight for volume.The compressive strength of concrete is roughly 5 to 10%that of steel,while its unit density is roughly 30%that of steel.As a result,a concrete structure requires a larger volume and a

26、 greater weight of material than does a comparable steel structure.As a result,long-span structures are often built from steel.4.Time-dependent volume changes.Both concrete and steel undergo-approximately the same amount of thermal expansion and contraction.Because there is less mass of steel to be

27、heated or cooled,and because steel is a better concrete,a steel structure is generally affected by temperature changes to a greater extent than is a concrete structure.On the other hand,concrete undergoes frying shrinkage,which,if restrained,may cause deflections or cracking.Furthermore,deflections

28、will tend to increase with time,possibly doubling,due to creep of the concrete under sustained loads.In almost every branch of civil engineering and architecture extensive use is made of reinforced concrete for structures and foundations.Engineers and architects requires basic knowledge of reinforce

29、d concrete design throughout their professional careers.Much of this text is directly concerned with the behavior and proportioning of components that make up typical reinforced concrete structures-beams,columns,and slabs.Once the behavior of these individual elements is understood,the designer will

30、 have the background to analyze and design a wide range of complex structures,such as foundations,buildings,and bridges,composed of these elements.Since reinforced concrete is a no homogeneous material that creeps,shrinks,and cracks,its stresses cannot be accurately predicted by the traditional equa

31、tions derived in a course in strength of materials for homogeneous elastic materials.Much of reinforced concrete design in therefore empirical,i.e.,design equations and design methods are based on experimental and time-proved results instead of being derived exclusively from theoretical formulations

32、.A thorough understanding of the behavior of reinforced concrete will allow the designer to convert an otherwise brittle material into tough ductile structural elements and thereby take advantage of concretes desirable characteristics,its high compressive strength,its fire resistance,and its durabil

33、ity.Concrete,a stone like material,is made by mixing cement,water,fine aggregate(often sand),coarse aggregate,and frequently other additives(that modify properties)into a workable mixture.In its unhardened or plastic state,concrete can be placed in forms to produce a large variety of structural elem

34、ents.Although the hardened concrete by itself,i.e.,without any reinforcement,is strong in compression,it lacks tensile strength and therefore cracks easily.Because unreinforced concrete is brittle,it cannot undergo large deformations under load and fails suddenly-without warning.The addition fo stee

35、l reinforcement to the concrete reduces the negative effects of its two principal inherent weaknesses,its susceptibility to cracking and its brittleness.When the reinforcement is strongly bonded to the concrete,a strong,stiff,and ductile construction material is produced.This material,called reinfor

36、ced concrete,is used extensively to construct foundations,structural frames,storage takes,shell roofs,highways,walls,dams,canals,and innumerable other structures and building products.Two other characteristics of concrete that are present even when concrete is reinforced are shrinkage and creep,but

37、the negative effects of these properties can be mitigated by careful design.A code is a set technical specifications and standards that control important details of design and construction.The purpose of codes it produce structures so that the public will be protected from poor of inadequate and con

38、struction.Two types f coeds exist.One type,called a structural code,is originated and controlled by specialists who are concerned with the proper use of a specific material or who are involved with the safe design of a particular class of structures.The second type of code,called a building code,is

39、established to cover construction in a given region,often a city or a state.The objective of a building code is also to protect the public by accounting for the influence of the local environmental conditions on construction.For example,local authorities may specify additional provisions to account

40、for such regional conditions as earthquake,heavy snow,or tornados.National structural codes genrally are incorporated into local building codes.The American Concrete Institute(ACI)Building Code covering the design of reinforced concrete buildings.It contains provisions covering all aspects of reinfo

41、rced concrete manufacture,design,and construction.It includes specifications on quality of materials,details on mixing and placing concrete,design assumptions for the analysis of continuous structures,and equations for proportioning members for design forces.All structures must be proportioned so th

42、ey will not fail or deform excessively under any possible condition of service.Therefore it is important that an engineer use great care in anticipating all the probable loads to which a structure will be subjected during its lifetime.Although the design of most members is controlled typically by de

43、ad and live load acting simultaneously,consideration must also be given to the forces produced by wind,impact,shrinkage,temperature change,creep and support settlements,earthquake,and so forth.The load associated with the weight of the structure itself and its permanent components is called the dead

44、 load.The dead load of concrete members,which is substantial,should never be neglected in design computations.The exact magnitude of the dead load is not known accurately until members have been sized.Since some figure for the dead load must be used in computations to size the members,its magnitude

45、must be estimated at first.After a structure has been analyzed,the members sized,and architectural details completed,the dead load can be computed more accurately.If the computed dead load is approximately equal to the initial estimate of its value(or slightly less),the design is complete,but if a s

46、ignificant difference exists between the computed and estimated values of dead weight,the computations should be revised using an improved value of dead load.An accurate estimate of dead load is particularly important when spans are long,say over 75 ft(22.9 m),because dead load constitutes a major p

47、ortion of the design load.Live loads associated with building use are specific items of equipment and occupants in a certain area of a building,building codes specify values of uniform live for which members are to be designed.After the structure has been sized for vertical load,it is checked for wi

48、nd in combination with dead and live load as specified in the code.Wind loads do not usually control the size of members in building less than 16 to 18 stories,but for tall buildings wind loads become significant and cause large forces to develop in the structures.Under these conditions economy can

49、be achieved only by selecting a structural system that is able to transfer horizontal loads into the ground efficiently.钢筋混凝土 在每一种国家，混凝土及钢筋混凝土都被用来作为建筑材料。诸多地区，包括美国和加拿大，钢筋混凝土在工程建设中是重要旳构造材料。钢筋混凝土建筑旳普遍性源于钢筋旳广泛供应和混凝土旳构成成分，砾石，沙子，水泥等，混凝土施工所需旳技能相对简朴，与其他形式旳建设相比，钢筋混凝土愈加经济。混凝土及钢筋混凝土用于桥梁、多种地下构造建筑、水池、电视塔、海洋石油勘探建

50、筑、工业建筑、大坝，甚至用于造船业。钢筋混凝土构造也许是现浇混凝土构造，在其最终位置建造，或者他们也许是在一家工厂生产混凝土预制件，再在施工现场安装。混凝土构造在设计上也许是一般旳和多功能旳，或形状和布局是奇想和艺术旳。其他很少几种建材可以提供建筑和构造如此旳通用性和广泛合用性。混凝土有较强旳抗压力但抗拉力很弱。因此，混凝土，每当承受荷载时，或约束收缩或温度变化，引起拉应力，在超过抗拉强度时，裂缝开始发展。在素混凝土梁中，中和轴旳弯矩是由在混凝土内部拉压力偶来抵御作用荷载之后旳值。这种梁当出现第一道裂缝时就忽然完全地断裂了。在钢筋混凝土梁中，钢筋是那样埋置于混凝土中，以至于当混凝土开裂后弯矩平