ET-662 GPS模块.pdf

《ET-662 GPS模块.pdf》由会员分享，可在线阅读，更多相关《ET-662 GPS模块.pdf（22页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、 ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 2 of 23 Copyright 2007,GlobalSat Technology.1.Product Information Product Name:ET-662 Product Description:ET-662 is a compact,high performance,and low power consumption GPS engine board.It uses SiRF Star III chipse

2、t which can track up to 20 satellites at a time and perform fast TTFF in weak signal environments.ET-662 is suitable for the following applications:Automotive navigation Personal positioning Fleet management Mobile phone navigation Marine navigation Product Features:9 SiRF star III high performance

3、GPS Chipset 9 Very high sensitivity(Tracking Sensitivity:-159 dBm)9 Extremely fast TTFF(Time To First Fix)at low signal level 9 Two serial ports 9 4Mb flash 9 Built-in LNA 9 Compact size(22.4 x 17 x 3 mm)suitable for space-sensitive application 9 One size component,easy to mount on another PCB board

4、 9 Support NMEA 0183 and SiRF binary protocol Product Specifications GPS Receiver Chipset SiRF GSC3f/LPx Frequency L1,1575.42 MHz Code C/A Code Protocol NMEA 0183 v2.2 Default:GGA,GSA,GSV,RMC Support:VTG,GLL,ZDA)SiRF binary and NMEA Command Available Baud Rate 4,800 to 57,600 bps adjustable ET-662 V

5、e rsion 2.1 The Specifications are subject to be changed without notice.Page 3 of 23 Copyright 2007,GlobalSat Technology.Channels 20 Flash 4Mbit Sensitivity Tracking:-159dBm Cold Start 42 seconds,average Warm Start 38 seconds,average Hot Start 1 second,average Reacquisition 0.1 second,average Accura

6、cy Position:10 meters,2D RMS 5 meters,2D RMS,WAAS enabled Velocity:0.1 m/s Time:1us synchronized to GPS time Maximum Altitude 18,000 meter Maximum Velocity 515 meter/second Maximum Acceleration 4G Update Rate 1 Hz DGPS WAAS,EGNOS,MSAS Datum WGS-84 Interface I/O Pins 2 serial ports Physical Character

7、istic Type 28-pin stamp holes Dimensions 22.4 mm*17 mm*3 mm 0.2mm DC Characteristics Power Supply 3.3Vdc 5%Backup Voltage 2.0 3.6Vdc Power Consumption Acquisition:40mA Tracking:25mA Environmental Range Humidity Range 5%to 95%non-condensing Operation Temperature-40 to 85 Storage Temperature-40 to 85

8、ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 4 of 23 Copyright 2007,GlobalSat Technology.2.Technical Information Block Diagram ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 5 of 23 Copyright 2007,GlobalSat Technology.Modu

9、le Pin Assignment:ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 6 of 23 Copyright 2007,GlobalSat Technology.Pin#Name Description 1 TXD1 Serial output for channel 2 RXD1 Serial input for channel 3 TXD0 Serial output for channel 4 RXD0 Serial input for channel 5

10、VCC DC supply voltage input 6 VCC DC supply voltage input 7 GND Ground 8 VDD 28OUT Output voltage 2.85V 9 NC NC 10 RESET_N Reset(Active low)11 V_BAT Backup battery supply voltage 12 NC NC 13 GND Ground 14 GND Ground 15 GND Ground 16 RF_IN GPS RF signal input 17 GND Ground 18 VCC_RF Supply Antenna Bi

11、as voltage 19 V_ANT Antenna Bias voltage(must connect to ground if not used)20 NC NC 21 NC NC 22 NC NC 23 NC NC 24 NC NC 25 NC NC 26 NC NC 27 EXTINT0 External Interrupt 28 TIME PULSE One Pulse Per Second ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 7 of 23 Cop

12、yright 2007,GlobalSat Technology.Application Circuit ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 8 of 23 Copyright 2007,GlobalSat Technology.GPS Active Antenna Specifications(Recommendation)Frequency:1575.42+2MHz Axial Ratio:3 dB Typical Output Impedance:50 P

13、olarization:RHCP Amplifier Gain:1822dB Typical Output VSWR:2.0 Max.Noise Figure:2.0 dB Max Antenna Input Voltage:2.85V(Typ.)ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 9 of 23 Copyright 2007,GlobalSat Technology.Dimensions ET-662 Ve rsion 2.1 The Specificatio

14、ns are subject to be changed without notice.Page 10 of 23 Copyright 2007,GlobalSat Technology.Recommended Layout PAD Tolerance:0.1mm ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 11 of 23 Copyright 2007,GlobalSat Technology.Recommended Reflow Profile:Pre heatin

15、g temperature:150 10 Pre heating time:90 30sec.Heating temperature:235 5 Heating time:10 1sec.Peak temperature must not exceed 240 and the duration of over 200 should be 30 10 Seconds.Temperature 240 Max.235 5.10 1s 200 150 10 30 10s 90 30s Time sec.ET-662 Ve rsion 2.1 The Specifications are subject

16、 to be changed without notice.Page 12 of 23 Copyright 2007,GlobalSat Technology.SOFTWARE COMMAND NMEA Output Command GGA-Global Positioning System Fixed Data Table B-2 contains the values for the following example:$GPGGA,161229.487,3723.2475,N,12158.3416,W,1,07,1.0,9.0,M,0000*18 Table B-2 GGA Data F

17、ormat Name Example Units Description Message ID$GPGGA GGA protocol header UTC Time 161229.487 hhmmss.sss Latitude 3723.2475 ddmm.mmmm N/S Indicator N N=north or S=south Longitude 12158.3416 dddmm.mmmm E/W Indicator W E=east or W=west Position Fix Indicator 1 See Table B-3 Satellites Used 07 Range 0

18、to 12 HDOP 1.0 Horizontal Dilution of Precision MSL Altitude1 9.0 meters Units M meters Geoid Separation1 meters Units M meters Age of Diff.Corr.second Null fields when DGPS is not used Diff.Ref.Station ID 0000 Checksum*18 End of message termination SiRF Technology Inc.does not support geoid correct

19、ions.Values are WGS84 ellipsoid heights.Table B-3 Position Fix Indicator Value Description 0 Fix not available or invalid 1 GPS SPS Mode,fix valid 2 Differential GPS,SPS Mode,fix valid 3 GPS PPS Mode,fix valid ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 13 of

20、 23 Copyright 2007,GlobalSat Technology.Name Example Units Description Message ID$GPGSA GSA protocol header Mode1 A See Table B-6 Mode2 3 See Table B-7 Satellite Used1 07 Sv on Channel 1 Satellite Used1 02 Sv on Channel 2.Satellite Used1 Sv on Channel 12 PDOP 1.8 Position dilution of Precision HDOP

21、1.0 Horizontal dilution of Precision VDOP 1.5 Vertical dilution of Precision Checksum*33 End of message termination GLL-Geographic Position-Latitude/Longitude Table B-4 contains the values for the following example:$GPGLL,3723.2475,N,12158.3416,W,161229.487,A*2C Table B-4 GLL Data Format Name Exampl

22、e Units Description Message ID$GPGLL GLL protocol header Latitude 3723.2475 ddmm.mmmm N/S Indicator n N=north or S=south Longitude 12158.3416 dddmm.mmmm E/W Indicator W E=east or W=west UTC Position 161229.487 hhmmss.sss Status A A=data valid or V=data not valid Checksum*2C End of message terminatio

23、n GSA-GNSS DOP and Active Satellites Table B-5 contains the values for the following example:$GPGSA,A,3,07,02,26,27,09,04,15,1.8,1.0,1.5*33 Table B-5 GSA Data Format 1.Satellite used in solution.Table B-6 Mode1 Value Description M Manual-forced to operate in 2D or 3D mode A 2Dautomatic-allowed to au

24、tomatically switch 2D/3D Table B-7 Mode 2 Value Description ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 14 of 23 Copyright 2007,GlobalSat Technology.1 Fix Not Available 2 2D 3 3D GSV-GNSS Satellites in View Table B-8 contains the values for the following exam

25、ple:$GPGSV,2,1,07,07,79,048,42,02,51,062,43,26,36,256,42,27,27,138,42*71$GPGSV,2,2,07,09,23,313,42,04,19,159,41,15,12,041,42*41 Table B-8 GSV Data Format Name Example Description Message ID$GPGSV GSV protocol header Number of Messages1 2 Range 1 to 3 Message Number1 1 Range 1 to 3 Satellites in View

26、 07 Satellite ID 07 Channel 1(Range 1 to 32)Elevation 79 degrees Channel 1(Maximum90)Azimuth 048 degrees Channel 1(True,Range 0 to 359)SNR(C/No)42 dBHz Range 0 to 99,null when not tracking.Satellite ID 27 Channel 4(Range 1 to 32)Elevation 27 Degrees Channel 4(Maximum90)Azimuth 138 Degrees Channel 4(

27、True,Range 0 to 359)SNR(C/No)42 dBHz Range 0 to 99,null when not tracking Checksum*71 End of message termination Depending on the number of satellites tracked multiple messages of GSV data may be required.RMC-Recommended Minimum Specific GNSS Data Table B-10 contains the values for the following exa

28、mple:$GPRMC,161229.487,A,3723.2475,N,12158.3416,W,0.13,309.62,120598,*10 Table B-10 RMC Data Format Name Example Units Description Message ID$GPRMC RMC protocol header UTC Time 161229.487 hhmmss.sss Status A A=data valid or V=data not valid Latitude 3723.2475 ddmm.mmmm N/S Indicator N N=north or S=s

29、outh Longitude 12158.3416 dddmm.mmmm E/W Indicator W E=east or W=west Speed Over Ground 0.13 knots ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 15 of 23 Copyright 2007,GlobalSat Technology.Course Over Ground 309.62 degrees True Date 120598 ddmmyy Magnetic Vari

30、ation2 degrees E=east or W=west Checksum*10 End of message termination SiRF Technology Inc.does not support magnetic declination.All“course over ground”data are geodetic WGS48 directions.VTG-Course Over Ground and Ground Speed$GPVTG,309.62,T,M,0.13,N,0.2,K*6E Name Example Units Description Message I

31、D$GPVTG VTG protocol header Course 309.62 degrees Measured heading Reference T True Course degrees Measured heading Reference M Magnetic Speed 0.13 knots Measured horizontal speed Units N Knots Speed 0.2 Km/hr Measured horizontal speed Units K Kilometers per hour Checksum*6E End of message terminati

32、on ET-662 Ve rsion 2.1 The Specifications are subject to be changed without notice.Page 16 of 23 Copyright 2007,GlobalSat Technology.2.2 NMEA Input Command A).Set Serial Port ID:100 Set PORTA parameters and protocol This command message is used to set the protocol(SiRF Binary,NMEA,or USER1)and/or th

33、e communication parameters(baud,data bits,stop bits,parity).Generally,this command would be used to switch the module back to SiRF Binary protocol mode where a more extensive command message set is available.For example,to change navigation parameters.When a valid message is received,the parameters

34、will be stored in battery backed SRAM and then the receiver will restart using the saved parameters.Format:$PSRF100,*CKSUM 0=SiRF Binary,1=NMEA,4=USER1 1200,2400,4800,9600,19200,38400 8,7.Note that SiRF protocol is only valid f8 Data bits 0,1 0=None,1=Odd,2=Even Example 1:Switch to SiRF Binary proto

35、col at 9600,8,N,1$PSRF100,0,9600,8,1,0*0C Example 2:Switch to User1 protocol at 38400,8,N,1$PSRF100,4,38400,8,1,0*38 *Checksum Field:The absolute value calculated by exclusive-OR the 8 data bits of each character in the Sentence,between,but excluding“$”and“*”.The hexadecimal value of the most signif

36、icant and least significant 4 bits of the result are convertted to two ASCII characters(0-9,A-F)for transmission.The most significant character is transmitted first.*:Hex 0D 0A B).Navigation lnitialization ID：101 Parameters required for start This command is used to initialize the module for a warm

37、start,by providing current position（in X,Y,Z The Specifications are subject to be changed without notice.Page 17 of 23 Copyright 2007,GlobalSat Technology.ET-662 Ve rsion 2.1 coordinates）,clock offset,and time.This enables the receiver to search for the correct satellite signals at the correct signa

38、l parameters.Correct initialization parameters will enable the receiver to acquire signals more quickly,and thus,produce a faster navigational solution.When a valid Navigation Initialization command is received,the receiver will restart using the input parameters as a basis for satellite selection a

39、nd acquisition.Format：$PSRF101,*CKSUM X coordinate position INT32 Y coordinate position INT32 Z coordinate position INT32 Clock offset of the receiver in Hz,Use 0 for last saved value if available.If this is unavailable,a default value of 75000 for GSP1,95000 for GSP 1/LX will be used.INT32 GPS Time

40、 Of Week UINT32 GPS Week Number UINT16 （Week No and Time Of Week calculation from UTC time）Number of channels to use.1-12.If your CPU throughput The Specifications are subject to be changed without notice.Page 18 of 23 Copyright 2007,GlobalSat Technology.ET-662 Ve rsion 2.1 is not high enough,you co

41、uld decrease needed throughput by reducing the number of active channels UBYTE bit mask 0 01=Data Valid warm/hotstarts=1 0 02=clear ephemeris warm start=1 0 04=clear memory.Cold start=1 UBYTE Example:Start using known position and time.PSRF101,-2686700,-4304200,3851624,96000,497260,921,12,3*7F C).Se

42、t DGPS Port ID:102 Set PORT B parameters for DGPS input This command is used to control Serial Port B that is an input only serial port used to receive RTCM differential corrections.Differential receivers may output corrections using different communication parameters.The default communication param

43、eters for PORT B are 9600 Baud,8data bits,0 stop bits,and no parity.If a DGPS receiver The Specifications are subject to be changed without notice.Page 19 of 23 Copyright 2007,GlobalSat Technology.ET-662 Ve rsion 2.1 is used which has different communication parameters,use this command to allow the

44、receiver to correctly decode the data.When a valid message is received,the parameters will be stored in battery backed SRAM and then the receiver will restart using the saved parameters.Format:PSRF102,*CKSUM 1200,2400,4800,9600,19200,38400 8 0,1 0=None,Odd=1,Even=2 Example:Set DGPS Port to be 9600,8

45、,N,1 PSRF102,9600,8,1.0*12 D).Query/Rate Control ID:103 Query standard NMEA message and/or set output rate This command is used to control the output of standard NMEA message GGA,GLL,GSA,GSV RMC,VTG.Using this command message,standard NMEA message may be polled once,or setup for periodic output.Chec

46、ksums may also be enabled or disabled depending on the needs of the receiving program.NMEA message settings are saved in battery backed memory for each entry when the message is accepted.The Specifications are subject to be changed without notice.Page 20 of 23 Copyright 2007,GlobalSat Technology.ET-

47、662 Ve rsion 2.1 Format:PSRF103,*CKSUM 0=GGA,1=GLL,2=GSA,3=GSV,4=RMC,5=VTG 0=SetRate,1=Query Output every seconds,off=0,max=255 0=disable Checksum,1=Enable checksum for specified message Example 1:Query the GGA message with checksum enabled PSRF103,00,01,00,01*25 Example 2:Enable VTG message for a 1

48、Hz constant output with checksum enabled PSRF103,05,00,01,01*20 Example 3:Disable VTG message PSRF103,05,00,00,01*21 E).LLA Navigation lnitialization ID:104 Parameters required to start using Lat/Lon/Alt This command is used to initialize the module for a warm start,by providing current position(in

49、Latitude,Longitude,Altitude coordinates),clock offset,and time.This enables the receiver to search for the correct satellite signals at the correct signal parameters.Correct initialization parameters will enable the receiver to acquire signals more quickly,and thus,will produce a The Specifications

50、are subject to be changed without notice.Page 21 of 23 Copyright 2007,GlobalSat Technology.ET-662 Ve rsion 2.1 faster navigational soution.When a valid LLANavigationInitialization command is received,the receiver will restart using the input parameters as a basis for satellite selection and acquisit