采用超临界水中氧气回收碳纤维增强树脂基复合材料中的碳纤维.pdf

《采用超临界水中氧气回收碳纤维增强树脂基复合材料中的碳纤维.pdf》由会员分享，可在线阅读，更多相关《采用超临界水中氧气回收碳纤维增强树脂基复合材料中的碳纤维.pdf（4页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、Short CommunicationChemical recycling of carbon fibers reinforced epoxy resin compositesin oxygen in supercritical waterYongping Baia,Zhi Wangb,*,Liqun FengaaSchool of Chemical Engineering and Technology,Harbin Institute of Technology,Harbin 150001,ChinabCenter for Composite Materials,Harbin Institu

2、te of Technology,Harbin 150001,Chinaa r t i c l ei n f oArticle history:Received 29 June 2009Accepted 30 July 2009Available online 3 August 2009a b s t r a c tThe carbon fibers in carbon fibers reinforced epoxy resin composites were recovered in oxygen in super-critical water at 30 1 MPa and 440 10?

3、C.The microstructure of the recovered carbon fibers wasobserved using scanning electron microscopy(SEM)and atom force microscopy(AFM).The resultsrevealed that the clean carbon fibers were recovered and had higher tensile strength relative to the virgincarbon fibers when the decomposition rate was ab

4、ove 85 wt.%,although the recovered carbon fibers haveclean surface,the epoxy resin on the surface of the recovered carbon fibers was readily observed.As thedecomposition rate increased to above 96 wt.%,no epoxy resin was observed on the surface of the carbonfibers and the oxidation of the recovered

5、carbon fibers was readily measured by X-ray photoelectronspectroscopy(XPS)analysis.The carbon fibers were ideally recovered and have original strength whenthe decomposition rates were between 94 and 97 wt.%.This study clearly showed the oxygen in super-critical water is a promising way for recycling

6、 the carbon fibers in carbon fibers reinforced resincomposites.?2009 Elsevier Ltd.All rights reserved.1.IntroductionCarbon fibers reinforced resin matrix composites are a class ofadvanced materials that have been developed for a variety of appli-cations in high-technology fields,such as the aerospac

7、e and auto-mobile industries,as well as in sporting goods 15.Since mostcarbon fibers are utilized with epoxy matrix in the form of compos-ites,a high scrap rate and significant amounts of off-cuts and re-jects are generated during the manufacture of these thermosetcomposites in contrast to the manuf

8、acturing of thermoplastic com-posites 5,6.Carbon fibers reinforced resin matrix composites thatwere destroyed in the course of use will become waste.Togetherwith end of life components,the amount of waste carbon fibersreinforced resin matrix composites has reached a significant level.At present time

9、,the waste composites are mostly disposed of inlandfill because there is no economic means of recycling the wastecomposites.This results in the increase in the non-degradablewastes and also the loss of high value carbon fibers.An effectiverecycling process is therefore highly desirable in order to r

10、eclaimthe high value carbon fibers and reduce the pressure on the sur-rounding environment.Recycling the thermoset resin matrixcomposites has been extensively studied.For example,the carbonfibers reinforced resin matrix composites were degraded by pyro-lysis in the absence of oxygen 79,by chemical m

11、ethod and byusing catalyststoforma mixture oforganic compositions10,11.Unfortunately,the above-mentioned methods result inthe formation of the layer char or non-decomposed resin matrixon the recovered carbon fibers.Supercriticalfluidsandespeciallysupercriticalwater(T 647.3 K,P 22.1 MPa)are also pote

12、ntial media for the recy-cling of fibers and resin since they can be inexpensive reactionmedia,recyclable,non-toxic and relatively easy to handle 12.The supercritical water also possesses an interesting combinationof properties such as low viscosity,high mass transport coeffi-cients,high diffusivity

13、 and solvation power.Furthermore,thesupercritical water has a high solubility for organic compoundand oxygen,especially oxygen and water can form a single andhomogeneous phase,which allows oxidation to proceed rapidlyby an elimination of the potential interface mass transport limita-tions.These prop

14、erties allow using water as reaction medium in-stead of hazardous volatile organic solvents 13.Although extensive research has been performed on the decom-position of the carbon fibers reinforced resin matrix compositesand the applications of the supercritical water in industry,thereare a few of the

15、 literature on the supercritical water decompositionof the carbon fibers reinforced resin matrix composites.In the present work,the oxygen was added into water in orderto increase the decomposition ability of the supercritical water.The carbon fibers reinforced resin matrix composite was decom-posed

16、 by the oxygen in supercritical water.The surface microstruc-ture of the recovered carbon fibers was investigated using atomic0261-3069/$-see front matter?2009 Elsevier Ltd.All rights reserved.doi:10.1016/j.matdes.2009.07.057*Corresponding author.Tel/fax:+86 451 86413711.E-mail address:(Z.Wang).Mate

17、rials and Design 31(2010)9991002Contents lists available at ScienceDirectMaterials and Designjournal homepage: microscopy and scanning electron microscopy.Furthermore,the tensile strength of the recovered carbon fibers was evaluatedby single fiber strength.2.ExperimentalCommercially available T-300T

18、Mcarbon fibers with a diameter ofabout 67lm,purchased from Japan Toray,was used as reinforcefiller in the present work.E-51 epoxy resin was obtained fromYueyang Chemical Co.Ltd.,China.The phthalic anhydride was cho-senascuringagent.Epoxyresin/phthalicanhydride/benzyldimethylamine were 100,70 and 1 p

19、arts by weight,respectively.The prepreg that was fabricated by the carbon fibers and epoxy re-sin was put unidirectional into a mold to manufacture composites.The prepreg was pressed and cured under 5 MPa pressure for 2 h at90?C,then under 10 MPa pressure for 2 h at 120?C and last under10 MPa pressu

20、re for 4 h at 150?C by hotpress machine and hot-pressed composite with fibers mass fraction of 65(1.5%).Thedecomposition pressure and temperature in the reactor was main-tained at 30 1 MPa and 440 10?C.The composite was decom-posed in oxygen in supercritical water from 25 to 35 min.Themass ratio of

21、the composite to water was below 10%.The surfacemicrostructure of the carbon fibers was examined on a Russian sol-ver P47 atom force microscopy(AFM)and Hitachi S-4700 scanningelectron microscopy(SEM).The surface element concentration ofthe carbon fibers was measured using the X-ray photoelectronspec

22、troscopy(XPS)along with an X-ray photoelectron spectrome-ter(Perkin-Elmer,PHI 5300)equipped with magnesium X-raysource.Furthermore,the tensile strength of the recovered carbonfibers was evaluated by single fiber strength.A minimum numberof 120 specimens were tested for each treatment condition.Thesi

23、ngle fiber specimens were prepared in paper frames with dimen-sions of 20 mm?100 mm.The free fiber length was approxi-mately 30 mm.A single fiber tensile test was carried out usingan interfacial micro-bond evaluation instrument made by ToheiSanyon Corporatin of Japan.The decomposition rate of epoxy

24、resinin composites was calculated according to the amount of solidcomposition after treatment using the following formula:Dr Mc?MrMe?100%where Dr.is the decomposition rate(wt.%),Mc is the mass of com-posite before decomposition treatment,Mr.is the mass of solidcomposition after decomposition treatme

25、nt and Me is the mass ofepoxy resin in composite before decomposition treatment.3.Results and discussion3.1.Surface microstructure and element compositionsFig.1 shows the SEM micrographs of the surface of the carbonfibers before and after treatment.It is recognized 14 that thecommercially available

26、T-300TMcarbon fibers have many surfacegrooves that was produced in the process of manufacture of thecarbon fibers as shown Fig.1A.The clean carbon fibers were recov-ered when the decomposition rate was above 85 wt.%.Althoughthe recovered carbon fibers have clean surface,the epoxy resinon the surface

27、 of the recovered carbon fibers was readily observedby SEM observation as shown in Fig.1B.As the decomposition rateincreased to above 96 wt.%,no epoxy resin was observed on thesurface of the carbon fibers compared with the commercial carbonfibers.The atom force microscopy(AFM)was used in order to ob

28、servethe surface microstructure of the carbon fibers.The virgin carbonfibers emerged after the commercial carbon fibers were treatedby the acetone extraction for 100 h 14.The surface of the virgincarbon fibers is relative smooth as shown in Fig.2A.The recoveredcarbon fibers were treated by the aceto

29、ne extraction for 100 h.Theepoxy resin on the surface of the recovered carbon fibers was notextracted by the acetone when the decomposition rate was below92 wt.%as shown in Fig.2B,which was presumably attributed tothat the epoxy resin was not completely decomposed.When thedecomposition rate was abov

30、e 94 wt.%as shown in Fig.2C,theepoxy resin was decomposed completely.Compared with the vir-gin carbon fiber surface,the amount of the surface groove in-creasedasthedecompositionrateincreasedwhenthedecomposition rate was above 96 wt.%,especially many grooveson the surface of the carbon fibers were in

31、corporated into a deepfurrow when the decomposition rate was 100.2 wt.%as shown inFig.2D.This was attributed to the excessive oxidation of recoveredcarbon fibers 15.The overall XPS spectra of different specimens are shown inFig.3.There are significant differences between the virgin andrecovered carb

32、on fibers.Table 1 summarizes the surface elementconcentration of different specimens obtained from XPS analysis.From these data,it was found that the surface elements of the vir-gin carbon fibers were mainly composed of the carbon,oxygen andnitrogen.The carbon and oxygen contents of the virgin carbo

33、n fi-bers were 90.13 and 7.44%and the O/C ratio was 0.0825.For therecovered carbon fiber of the decomposition rate of 100.2 wt.%,the carbon and oxygen contents were 69.09 and 28.65%,respec-tively,and the O/C ratio of 0.4147 was significantly higher thanthat of the virgin carbon fibers.This also reve

34、aled that the recov-ered carbon fibers were oxidized in oxygen in supercritical water15.3.2.Mechanical propertiesThe curve of tensile strength versus decomposition rate isshown in Fig.4.When the decomposition rate was below94 wt.%,the tensile strength of recovered carbon fibers was signif-icantly hi

35、gher than 3.11 GPa of the virgin carbon fibers,which wasattributed to the incompletely decomposed resin that could healthe surface flaws of the carbon fibers and avoid the effect of stressFig.1.The SEM micrographs of the surface of the carbon fibers before(A)and after(B)treatment.1000Y.Bai et al./Ma

36、terials and Design 31(2010)9991002concentration on the strength of the carbon fibers 14.When thedecomposition rates were 94.4 and 96.5 wt.%,the tensile strengthof the recovered carbon fibers were 3.15 and 3.13 GPa,respec-tively,which were statistically identical at 3.11GPa of the virgincarbon fibers

37、.The tensile strength of the recovered carbon fibersdecreased rapidly as the decomposition rate increased from96.5%to 100.2%,which was presumably attributed to the damageof the carbon fibers due to the excessive oxidation of recoveredcarbon fibers 15.From these results,it could be detected thatthe c

38、arbon fibers were ideally recovered and have original strengthwhen the decomposition rates were between 94 and 97 wt.%.Fig.2.The AFM micrographs of the surface of the carbon fibers;A,virgin carbon fibers;the decomposition rates of B,C,D were 91.2%,96.5%and 100.2%,respectively.Fig.3.The overall XPS s

39、pectra of different specimens.Table 1Atomic concentration of different specimens obtained from XPS spectra.SpecimensC(%)O(%)N(%)O/CVirgin fiber90.137.442.380.0825Recovered fiber69.0928.652.230.4147Fig.4.The curve of tensile strength versus decomposition rate.Y.Bai et al./Materials and Design 31(2010

40、)999100210014.ConclusionsThe clean carbon fibers were recovered in oxygen in supercrit-ical water at 30 1 MPa and 440 10?C for 30 5 min and hadhigher tensile strength relative to the virgin carbon fibers whenthe decomposition rate was above 85 wt.%.However,the tensilestrength of the recovered carbon

41、 fibers decreased rapidly as thedecomposition rate increased from 96.5%to 100.2%,which waspresumably attributed to the damage of the carbon fibers due tothe excessive oxidation of recovered carbon fibers.Combined withmicrostructure analysis,it could be detected that the carbon fiberswere ideally rec

42、overed and have original strength when thedecomposition rates were between 94 and 97 wt.%.References1 Rezaei F,Yunus R,Ibrahim NA.Effect of fiber length on thermomechanicalproperties of short carbon fiber reinforced polypropylene composites.MaterDes 2009;30:2603.2 Karnik SR,Gaitonde VN,Campos RJ,Est

43、eves CA,Abro AM,Davim PJ.Delamination analysis in high speed drilling of carbon fiber reinforcedplastics(CFRP)usingartificialneuralnetworkmodel.MaterDes2008;29:176876.3 Sari N,Snmazcelik T.Erosive wear behaviour of carbon fibre/polyetherimidecomposites under low particle speed.Mater Des 2007;28:3515

44、.4 Kishore RA,Tiwari R,Dvivedi A,Singh I.Taguchi analysis of the residual tensilestrength after drilling in glass fiber reinforced epoxy composites.Mater Des2009;30:218690.5 Jiang G,Pickering SJ,Walker GS,Bowering N,Wong KH,Rudd CD.Softionisation analysis of evolved gas for oxidative decomposition o

45、f an epoxyresin/carbon fibre composite.Thermochim Acta 2007;454:10915.6 Seo MK,Park SJ.Surface characteristics of carbon fibers modified by directoxyfluorination.J Colloid Interf Sci 2009;330:23742.7 Williams PT,Williams EA.Fluidised bed pyrolysis of low density polyethyleneto produce petrochemical

46、feedstock.J Anal Appl Pyrolysis 1999;51:10726.8 Simon CM,Kaminsky W.Chemical recycling of polytetrafluoroethylene bypyrolysis.Polym Degrad Stab 1998;62:17.9 Cunliffe AM,Jones N,Williams PT.Recycling of fibre-reinforced polymericwaste by pyrolysis:thermo-gravimetric and bench-scale investigations.J A

47、nalAppl Pyrolysis 2003;70:31538.10 Pin ero-Hernanz R,Dodds C,Hyde J,Garca-Serna J,Poliakoff M,Lester E,et al.Chemical recycling of carbon fibre reinforced composites in nearcritical andsupercritical water.Compos Part A 2008;39:45461.11 Pin ero-Hernanz R,Garca-Serna J,Dodds C,Hyde J,Poliakoff M,Cocer

48、o MJ,et al.Chemical recycling of carbon fibre composites using alcohols undersubcritical and supercritical conditions.J Supercrit Fluids 2008;46:8392.12 Xiu FR,Zhang FS.Recovery of copper and lead from waste printed circuitboards by supercritical water oxidation combined with electrokinetic process.

49、J Hazard Mater 2009;165:10027.13 Sun MC,Wu XQ,Zhang ZE,Han EH.Oxidation of 316 stainless steel insupercritical water.Corros Sci 2009;51:106972.14 He F,Wang MZ.Carbon fibers and their composites.Beijing:Science Press;1995.15 Guo H,Huang YD,Meng LH,Liu L,Fan DP,Liu DX.Interface property of carbonfibers/epoxy resin composite improved by hydrogen peroxide in supercriticalwater.Mater Lett 2009;63:15314.1002Y.Bai et al./Materials and Design 31(2010)9991002